Orolia RC102 Leitfaden

DOC09005E

Date of rev. JUL 18/2022

Revision 04

First Issue: MAR 02/2009

Orolia S.A.S

INSTALLATION MANUAL

USER MANUAL

P/N: S1820513-21

REMOTE CONTROL PANEL RC102

Users are kindly requested to notify Orolia Customer Support

of any discrepancy, omission or error found in this manual.

Please register a support ticket via the Orolia website:

https://www.orolia.com/support/

ARE STRICTLY RESERVED. THIS DOCUMENT AND ANY ATTACHED

MATERIALS CONTAINS PROPRIETARY AND CONFIDENTIAL

INFORMATION AND DATA AND IS THE SOLE PROPERTY OF OROLIA

S.A.S. THE DOCUMENTS, ANY ATTACHED MATERIALS AND/OR

INFORMATION CONTAINED THEREIN MUST NOT BE USED,

DISSEMINATED, OR DISTRIBUTED EXCEPT FOR THE AGREED

PURPOSE. UNAUTHORIZED USE, REPRODUCTION, OR ISSUE TO ANY

THIRD PARTY IS NOT PERMITTED WITHOUT THE PRIOR WRITTEN

CONSENT OF THE OROLIA GROUP. THIS DOCUMENT IS TO BE

RETURNED TO THE OROLIA GROUP WHEN THE AGREED PURPOSE IS

FULFILLED.

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

TABLE OF CONTENTS

TOC PAGE: 1

JUL 18/2022

Introduction ........................................................................................... 1

KANNAD ELTs System Presentation .................................................... 1

Description ............................................................................................ 2

General .................................................................................................................. 2

Mechanical design ................................................................................................. 3

RCP installation..................................................................................... 4

Installation recommendations ................................................................................ 4

RCP Installation procedure .................................................................................... 4

Mount RCP.......................................................................................................... 4

Connection of RCP bundle to ELT ...................................................................... 7

Working mode ....................................................................................... 8

Controls ................................................................................................................. 8

Working mode information ..................................................................................... 9

Remote control .................................................................................................... 9

Monitoring ........................................................................................................... 9

Operation ............................................................................................ 10

Stand by mode .................................................................................................... 11

ON mode ............................................................................................................. 11

RESET & TEST ................................................................................................... 11

Self test ............................................................................................................. 11

RESET .............................................................................................................. 12

RCP operational tests .......................................................................................... 12

Technical characteristics and compatibility ......................................... 14

Technical characteristics ..................................................................................... 14

Environmental characteristics ........................................................................... 14

Electrical characteristics .................................................................................... 14

Compatibility list ................................................................................................... 14

Schematics and diagrams ................................................................... 15

RC102 Outline dimensions and drilling mask ...................................................... 15

RC102 Wiring diagram ........................................................................................ 16

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 1

JUL 18/2022

1. Introduction

The instructions in this manual provide the information necessary for

installation and operation with the RC102 remote control panels.

IMPORTANT: Installation of this RCP is covered by Service Bulletin "SB

S1820513-25-02”. Please read carefully this Service Bulletin before

installing this RCP.

This Service Bulletin applies only to KANNAD 406 AF-COMPACT

P/N S1840501-01 at amendment M only.

(KANNAD 406 AF-COMPACT P/N S1840501-01 at amendment N or higher

are not concerned by this Service Bulletin).

This Service Bulletin is available at the following address:

Orolia S.A.S.

Z.I. des Cinq Chemins CS10028

Kannad Aviation

56520 GUIDEL - FRANCE

Web: https://www.orolia.com/support/

Tel.: +33 (0)2 97 02 49 00

2. KANNAD ELTs System Presentation

KANNAD ELTs system is composed of:

1. an ELT transmitter (Refer to B. Compatibility list, page 14) and its

mounting bracket;

2. a remote control panel;

3. a DIN-12 connector (P/N S1820514-03) or programming dongle

(P/N S1820514-01 or P/N S1820514-06);

4. an outside whip or rod antenna.

The transmitter and bracket are installed in the aircraft near the tail.

The remote control panel is installed in the cockpit and connected to the ELT

with a 2-wire bundle (not supplied).

The DIN-12 connector is used to connect the RCP bundle to the ELT, it may be

replaced by a programming dongle fulfilling two functions:

• programming of ELT;

• connection of RCP bundle to ELT.

The outside antenna is mounted on the fuselage near the tail.

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 2

JUL 18/2022

Figure 1: ELT system description

3. Description

A. General

The RC102 is the smallest version of remote control panels compatible

with KANNAD406 AF-COMPACT series ELTs. It is specially intended for

general aviation or helicopters and can also be adapted for «cabin

installations» or retrofits on board airliners thanks to its small dimensions.

The 102 enables remote control of the primary functions of KANNAD ELTs

(Manual activation, Reset andTest) as well as visual monitoring.

CAUTION: RC102 is not compatible with KANNAD 406 AF COMPACT

P/N S1840501-01 at amendment L or lower.

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 3

JUL 18/2022

B. Mechanical design

The RC102 kit is composed of:

1. two self adhesive front plates (black with white markings);

2. a red LED annunciator, a led stand, a led mounting, washers and nuts;

3. a PCB on which is soldered a 3-position toggle switch with 2 locked

positions and a momentary position plus its washer and nut;

4. an identification label.

5. a CAUTION label

Figure 2: RC102 Remote Control Panel Kit

These components are delivered in a kit and must be assembled then

directly mounted on the aircraft instrument panel.

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 4

JUL 18/2022

4. RCP installation

A. Installation recommendations

IMPORTANT: Installation of this RCP is covered by Service Bulletin

"SB S1820513-25-02": Refer to Section 1. Introduction, page 1.

The RCP shall be installed in the cockpit. The RCP shall be readily

accessible from the pilot’s normal seated position.

CAUTION: RC102 RCP may only be installed with KANNAD 406 AF

COMPACT P/N S1840501-01 at amendment M or higher or on

KANNAD 406 AF COMPACT ER P/N S1840501-04. A WARNING label

is supplied with the kit and must be stuck on the 2-wire bundle on the

ELT side.

2 types of front plates may be installed. Choose the appropriate front plate

according to the aircraft’s instrument panel.

Connection of RC102 requires a 2-wire bundle. A pin-to-pin wiring has to

be provided by the installer with AWG24 wires. Shielded wires are

recommended.

The wires are soldered to a PCB installed on the switch. This operation can

be carried out before installation.

On the ELT side, the wires are soldered to a 12-pin plug that can be either

a standard "DIN12 connector" (P/N S1820514-03) or a connector with an

integrated serial memory module called "Programming Dongle"

(P/N S1820514-01).

B. RCP Installation procedure

(1) Mount RCP

(Refer to Figure 3: RCP mounting diagram)

NOTE: Legs of LED must be protected by heat shrinkable sleeves.

Choose one of the front plates (1a or 1b) according to the space

available on the instrument panel.

Front plate (1a)

• Place the front plate (1a) on the instrument panel and use it as drilling

mask or;

• Trace the centers of the two holes according to drilling mask supplied;

• Drill a hole Ø 8 mm for the LED mounting (2) (top of the panel);

• Drill a hole Ø6.5 mm for the switch (3b) (bottom of the panel);

Note: the switch (3b) is already soldered to a PCB (3a)

• Tear off protection of front plate (1a) from self-adhesive film;

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 5

JUL 18/2022

• Stick the front plate (1a) onto the instrument panel;

• Install the LED mounting (2), with washer (2a) and nut (2b). Tighten

nut;

• Connect the anode (long leg) of LED (2c) to A of PCB (3a);

• Connect the cathode (short leg) of LED (2c) to C of PCB (3a);

• Connect wires to K and M of PCB (3a);

• Insert the LED into the LED stand (2d) taking care the flat part of the

LED be in front of the flat part of the LED stand;

• Insert LED (2c) fitted with LED stand (2d) inside the LED mounting (2);

• Install the switch and PCB assembly (3b+3a) with washers (3c) and

nuts (3d), locked position upwards. Tighten nut;

• Stuck the "identification label" (4) on the cable bundle near the PCB.

Front plate (1b)

• Place the front panel (1b) on to the instrument panel and use it as

drilling mask or;

• Trace the centers of the two holes according to drilling mask supplied;

• Drill a hole Ø 8 mm for the LED mounting (2) (left of the panel);

• Drill a hole Ø6.5 mm for the switch (3b) (right of the panel);

Note: the switch (3b) is already soldered to a PCB (3a).

• Drill 4 holes of Ø 3 mm for the screws used to fix the RCP;

• Screw the front plate (1b) onto the instrument panel;

• Install the LED mounting (2), with washer (2a) and nut (2b). Tighten

nut;

• Connect the anode (long leg) of LED (2c) to A of PCB (3a);

• Connect the cathode (short leg) of LED (2c) to C of PCB (3a);

• Connect wires to K and M of PCB (3a);

• Insert the LED into the LED stand (2d) taking care the flat part of the

LED be in front of the flat part of the LED stand;

• Insert LED (2c) fitted with LED stand (2d) inside the LED mounting (2);

• Install the switch and PCB assembly (3b+3a) with washers (3c) and

nuts (3d), locked position upwards. Tighten nut;

• Stuck the "identification label" (4) on the cable bundle near the PCB.

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 6

JUL 18/2022

Figure 3: RCP mounting diagram

INSTALLATION MANUAL / USER MANUAL

REMOTE CONTROL PANEL RC102

PAGE: 7

JUL 18/2022

(2) Connection of RCP bundle to ELT

Refer to Figure 4: Wiring of 2-wire bundle between RC102 and ELT.

CAUTION: RC102 can be connected only to KANNAD 406 AF-

COMPACT ELT transmitter P/N S1840501-01 at amendment equal

or higher than M or to any KANNAD 406 AF COMPACT ER P/N

S1840501-04.

Solder the DIN12 connector or Programming Dongle on the other side

of the bundle (pins K and M):

• Connect the wire from M of PCB (3a) to pin M of DIN12 connector;

• Connect the wire from K of PCB (3a) to pin K of DIN12 connector.

• Stuck the "CAUTION label" (5) on the cable bundle close to the DIN12

connector.

Perform an RCP test (Refer to D. RCP operational tests, page 12).

Figure 4: Wiring of 2-wire bundle between RC102 and ELT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Orolia Fernbedienung Handbücher

Orolia

Orolia kannad aviation RC100 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung