Oster 6014 Bedienungsanleitung

Instruction Manual

Steam Iron

PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

Manuel d'Instructions

Fer À Vapeur

LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILIZER CET APPAREIL

Manual de Instrucciones

Plancha de Vapor

LEA TODAS LAS INSTRUCCIONES ANTES DE USAR ESTE APARATO

Manual de Instruções

Ferro Elétrico a Vapor

LEIA TODAS AS INSTRUÇÕES ANTES DE USAR ESTE APARELHO

6014, 6015

& 6016

6014, 6015

& 6016

STEAM MASTER® IRON

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed,

including the following:

• READ ALL INSTRUCTIONS BEFORE USE.

• Use Iron only for its intended use.

• To protect against risk of electric shock, do not immerse the Iron in water or other

liquids.

• The Fabric Select Dial and Steam Lever should always be turned to O/Off and

before plugging or unplugging from outlet. Never yank Cord to disconnect from outlet;

instead, grasp Plug and pull to disconnect.

• Do not allow Cord to touch hot surfaces. Let Iron cool completely before putting

away. Loop Cord loosely around Iron when storing.

• Always disconnect Iron from electrical outlet when filling with water or emptying

and when not in use.

• Do not operate Iron with a damaged Cord or if the Iron has been dropped or damaged.

To avoid the risk of electric shock, do not disassemble the Iron. Take it to an Oster®

Authorized Service Center for examination and/or repair. Incorrect reassembly can

cause a risk of electric shock when the Iron is used.

• Close supervision is necessary for any appliance being used by or near children.

Do not leave Iron unattended while plugged in or turned on or on an ironing board.

• Burns can occur from touching hot metal parts, hot water or steam. Use caution when

you turn a Steam Iron upside down - there may be hot water in the Reservoir.

• If the Iron is not operating normally, disconnect from the power supply and have the

Iron serviced by an Oster® Authorized Service Center.

• Your OSTER® Iron is designed to rest on the heel rest. Do not leave the Iron

unattended. Do not set the Iron on an unprotected surface, even if it is on its

heel rest.

• This is a high wattage appliance. To avoid a circuit overload, do not operate another

high wattage appliance on the same circuit.

• If an extension cord is absolutely necessary, a 15-ampere cord should be used.

Cords rated for less amperage may overheat. Care should be taken to arrange the

extension cord so that it cannot be pulled or tripped over.

SAVE THESE INSTRUCTIONS

(For 120 & 127 Volts)

To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is

wider than the other). This plug fits a polarized outlet only one way. This is a safety

feature intended to help reduce the risk of electrical shock. If the plug does not fit fully

into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do

not attempt to defeat this safety feature.

1. SPRAY MIST® Release

2. Covered Water Fill Hole

3. Fabric Select Dial

4. Steam/ Self-Clean Lever

5. SPRAY MIST® Button

6. SHOT OF STEAM®/ Vertical Shot of Steam Button

7. Power Indicator Light/MOTION SMART Auto-Off Indicatior

Blinking Light (model 6016 only)

8. 360° Tangle-Free Swivel Cord

9. See-Through Water Reservoir

10. Soleplate

DESCRIPTION OF THE APPLIANCE

Filling With Water

1. Make sure the iron is unplugged. Set the Steam Lever to and the Fabric

Select Dial to O/OFF.

2. Lift the Water Fill Hole Cover.

3. Fill water cup with water. Pour water into the Iron's Water Reservoir. Do not fill Water

Reservoir beyond maximum fill level.

WARNING: To prevent the risk of burns, be careful when filling a hot iron with water.

Hot metal parts, hot water and steam can cause injuries.

Dry Ironing

1. Make sure the Steam Lever is turned to the setting.

2. Plug the cord into the outlet.

3. Turn the Fabric Select Dial to the fabric setting you desire (Silk or Synthetics).

Allow the Iron to heat for 2 minutes. While the Iron is heating, make sure it is sitting on

its heel rest on a stable, protected surface.

NOTE: While the Steam Lever is turned to the setting, you may still use the

SHOT OF STEAM® or SPRAY MIST® features. Please make sure the Water

Reservoir is 1/4 full of water.

TIP: Refer to the "Ironing Guide" for the recommended setting for your fabric.

Steam Ironing

1. Follow the instructions for "Filling With Water".

2. Plug the cord into the outlet.

3. Turn the Fabric Select Dial to the fabric setting you desire (Synthetic, Silk, Linen,

Cotton or Wool). Allow the Iron to heat for 2 minutes. While the Iron is heating,

make sure it is sitting on its heel rest on a stable, protected surface.

4. Allow the Iron to heat for 2 minutes, and then turn the Steam Lever to the appropriate

setting.

5. Please note that your Steam Iron has an anti-drip system that

prevents water from leaking, spitting, and dripping from the steam

vents, even at the lowest ironing temperatures (model 6015 only).

TIP: Refer to the "Ironing Guide" for the recommended setting for your fabric.

IMPORTANT: When not ironing, always set the Steam Lever to and the

Fabric Select Dial to O/OFF.

INSTRUCTIONS FOR USE

Ironing Tips

• Always read garment labels and follow the manufacturer's ironing instructions.

• Sort the articles to be ironed according to the type of fabric.

• You should first iron garments requiring low temperature (e.g., silks and synthetics)

to avoid damaging them with an iron that is too hot.

• If you are unsure of the fabric content of the garment, test a small area, such as a

seam or facing, before ironing a visible area. Start with a low temperature and

gradually increase the heat to find the best setting.

• When changing the temperature from a high setting to a low setting, allow

approximately 5 minutes for the lower temperature to be reached.

• When steam ironing, use long, slow passes over the fabric. This will allow the steam

to penetrate the fabric while allowing the heat of the soleplate to dry out the moisture.

• To iron linens, turn garment inside out. Be careful not to use an iron that is too hot

because the lining may melt or stick to the soleplate.

• To iron zippers, use an ironing cloth or make sure the zipper is closed and iron over

the flap. Never iron directly over an unprotected zipper.

• Use the "Ironing Guide" to select the best setting and method for the fabric you plan to

iron.

* An ironing cloth is a cotton, dry-cleaned cloth that you place over the garment you are ironing

to prevent the fabric from looking shiny.

Note: Some fabrics may require more steam than others. Your iron has the capability to adjust

steam as needed.

Suggested

Steam

Setting

Ironing

Recomendations Fabric Select

Dial Slecting

Fabric

Ironing Guide

Acrylic

Acetate

Polyester

Rayon

Silk

Viscose

Nylon

Wool

Wool Blends

Cotton Blends

Corduroy

Cotton

Linen

Denim

Synthetic

Silk

Wool

Cotton

Linen

Iron garment inside out

Iron garment inside out while still

damp.

Iron garment inside out while still

damp.

Iron garment inside out.

Iron garment inside out. Use an

ironing cloth* to prevent shine

marks.

Mainly dry iron; steam may be

used under garment

manufacturer’s instructions.

Iron garment inside out while still

damp.

Iron garment inside out or use an

ironing cloth.*

Iron garment inside out or use an

ironing cloth.*

Follow garment manufacturer’s

instructions.Use setting for the

fiber requiring the lowest setting.

Iron garment inside out or use an

ironing cloth* and then brush the

garment with your hand to raise

the texture of the fabric.

Iron dark fabrics inside out to

prevent shine marks.

Iron garment inside out or use an

ironing cloth* to prevent shine

marks (especially on dark fabrics).

Use the SPRAY MIST® and/or

the SHOT OF STEAM® feature

for deeper penetration to remove

wrinkles.

Spray Mist® Feature

The SPRAY MIST® feature is a powerful water spray mist that dampens the fabric to

aid in removing wrinkles from heavy fabrics and for setting creases.

To use the SPRAY MIST® Feature: Press the SPRAY MIST® Button firmly.

Shot of Steam® Feature

The SHOT OF STEAM® feature provides an extra burst of steam for deep penetration

of stubborn wrinkles. You can use this feature while dry or steam ironing, but the Water

Reservoir must be at least 1/4 full of water.

To use the SHOT OF STEAM® feature: Place the Iron on top of the wrinkle and press

the SHOT OF STEAM® Button each time you would like an extra burst of steam. The

SHOT OF STEAM® feature may be used continuously with just a short pause

between shots.

Vertical Steam and Vertical Shot of Steam

The Vertical Steam feature allows your Iron to function as a garment steamer.

TIP: When using the Vertical Steam on clothing, hang the clothing on a clothes hanger

for best results. Hanging curtains and drapes may also be steamed.

To use Vertical Steam:

1. Make sure that the Iron has heated up (2 minutes).

2. Hold the Iron in a vertical position, with the Iron close to but not touching the fabric

you want to steam.

3. With your other hand, pull the fabric tight.

4. Press the SHOT OF STEAM® Button for approximately 3-second intervals as you

move the Iron across the wrinkled area.

WARNING: To prevent the risk of burns, keep your hands away from the area being

steamed.

WARNING: DO NOT steam garments while wearing them; this may result in injuries.

USING THE IRON'S SPECIAL FEATURES

Patented Motion Smart® Auto-Off Feature

(Model 6016 Only)

When the Iron is plugged in, the Power Indicator will light steadily, indicating that there

is power to the Iron.

If you leave the Iron:

• In a horizontal position without moving it, or accidentally

tip the Iron over, it will automatically stop heating after

30 seconds. The Power Indicator will blink to let you

know that the Iron has stopped heating.

• In a vertical position (on its heel rest) without moving it,

the Iron will automatically turn off after 15 minutes.

The Power Indicator will blink to let you know that the

Iron has stopped heating.

IMPORTANT: The Power Indicator will continue to blink

until the Iron is unplugged or reset.

To reset the Iron:

Move the Iron back and forth and allow it to reheat for

2 minutes. The Indicator Light will stop blinking and

the Iron will start heating again.

WARNING: The patented MOTION SMART® Auto-Off is a safety feature, not a

recommended means for turning your Iron off. See "Caring for Your Iron

After Use" for information on turning off your Iron and storing it safely

between use.

Turning Off Your Iron

1. Turn the Steam Lever to and Fabric Select Dial to O/Off.

2. Unplug the Iron from the power source.

WARNING: NEVER yank the power Cord when unplugging the Iron. This can damage

the Cord.

Storing Your Iron

1. Allow the Iron to cool.

2. If you do not use your Iron on a daily basis, empty the Water Reservoir after each use

for a longer iron life. To do so, unplug the Iron, turn the Iron upside down, open the

Fill Hole Cover, and allow water to flow from the Fill Hole. Shake the Iron gently to

remove trapped water drops.

3. Loosely loop the power Cord around the heel rest and store the Iron on its heel rest.

IMPORTANT: Wrapping the Cord around the Iron too tightly can damage the Cord.

TIP: When not ironing, always set the Steam Lever to and the Fabric Select

Dial to O/Off.

Maintaining Your Steam Iron

CLEANING THE SOLEPLATE

Clean the Soleplate if starch or other residue accumulate.

To clean the Soleplate:

1. Allow the Iron to cool and then wipe it with a soft, damp cloth.

WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean

the Soleplate. This will damage the finish.

2. Run the Iron over an all-cotton cloth to remove any residue.

USING THE SELF-CLEANING FEATURE

You should use the Self-Cleaning feature once a month to maintain the optimal

performance of your Iron.

To use the Self-Cleaning feature:

1. Move the Steam Lever back and forth from several times to remove debris

and minerals from the Steam Valve. This keeps water flowing into the steam chamber.

CARING FOR YOUR IRON AFTER USE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Oster Eisen Handbücher

Oster

Oster PRESS X PRESS GCSTSG1200 Bedienungsanleitung

Oster

Oster GCSTEP2501 Bedienungsanleitung

Oster

Oster 4420-449 Bedienungsanleitung

Oster

Oster GCSTBS5803 Bedienungsanleitung

Oster

Oster GCSTDR1804 Bedienungsanleitung

Oster

Oster GCSTBS4801L Bedienungsanleitung

Oster

Oster GCSTTS7001 Bedienungsanleitung

Oster

Oster GCSTBS5001 Bedienungsanleitung

Oster

Oster GCSTBV4112 Bedienungsanleitung

Oster

Oster GCSTBS5802 Bedienungsanleitung

Oster

Oster GCSTSP6201 Bedienungsanleitung

Oster

Oster GCSTUP8201 Bedienungsanleitung

Oster

Oster GCSTBV4119 Bedienungsanleitung

Oster

Oster GCSTCW-317-013 Bedienungsanleitung

Oster

Oster 4019 Bedienungsanleitung

Oster

Oster 4415-449 Bedienungsanleitung

Oster

Oster GCSTBS6001 Bedienungsanleitung

Oster

Oster GCSTTS7010 Bedienungsanleitung

Oster

Oster GCSTCM2002P Bedienungsanleitung

Oster

Oster 5002 Bedienungsanleitung

Oster

Oster STEAM MASTER GCSTBSRC-202-013 Bedienungsanleitung

Oster

Oster PRESSXPRESS GCSTPX4060 Bedienungsanleitung

Oster

Oster 5104 Bedienungsanleitung

Oster

Oster GCSTBS3801 Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung

dyras

dyras ESI-2400AC Bedienungsanleitung

Philips

Philips PerfectCare PSG71 Series Bedienungsanleitung

GE 169061 Bedienungsanleitung