Outer Limits OLT-BAC-07 Bedienungsanleitung

OWNERS MANUAL

www.outer-limits.com.au

MODEL # OLT-BAC-07

BACKPACKER

IMPORTANT SAFETY AND

CARE INFORMATION

SAFETY HINTS

To prevent injury caused by re -

Do not pitch the tent near a camp re or any other ame source.

Do not use candles, matches or any other ame source in or near tent.

(This includes stoves, cooking equipment, lighting and heating appliances)

Only use recommended water repellent compounds on the tent y.

Do not spray tent fabric with insecticide.

To prevent injury caused by gas poisoning or suffocation –

Do not use fuel burning/oxygen consuming devices inside the tent. This includes candles, gas lanterns,

kerosene lamps, stoves, cooking appliances and heating appliances..

Do not use gas appliances of any kind inside the tent.

EXTREME CAUTION: Gas or fumes or lack of oxygen within the tent could result in unconsciousness

and brain damage and eventually death.

To prevent injury caused by your camping environment –

Do not pitch your tent under trees with dead branches or under trees known to drop branches.

Do not pitch your tent on an area that could get ooded.

Do not pitch your tent near cliffs in case of collapse or rock fall.

Do not leave tent erected in strong winds – collapse tent onto ground and seek refuge in your vehicle.

To prevent injury caused by electricity -

Always exercise care when using electricity and electric lighting in and near tents. Disconnect or turn off

during rain.

Keep all ame and heat sources away from the tent fabric.

This tent complies with the ammability requirements of CPAI-84. However, the

fabric may burn if left in continuous contact with a ame from any source. Also,

the application of any foreign substance to the tent fabric may render the ame

resistant properties ineffective.

UNDERSTANDING WATERPROOFNESS – WHAT IS NOT COVERED BY

WARRANTY!

OZtrail tents use waterproof and water repellent fabrics. However, with the addition of seams, zips

and other desirable features a recreational tent will not be as waterproof as a car, house or other solid

structures. The following are common examples of how water can enter a tent: -

Condensation – When warm moist air meets cooler air, clouds (condensation) occurs. A tent y is an

impermeable layer between the warm moist air inside the tent and the cooler air outside the tent. The

warm moist air condenses on the inside surface of the y. Condensation can be reduced if the tent is well

ventilated.

Seams – All seams are factory tape sealed but could leak at webbing and guy line entry points and

where there are multiple layers of fabric. If leakage at these points becomes a problem, simply use a

recommended seam sealant.

Zips – All care is taken in the design to cover zips with rain aps. At times wind driven rain could force

water through the zips. To minimise this, make sure all doors are closed correctly and that the aps cover

the zips.

Floor – If the ground is very wet or water pools under the oor, the downward pressure of standing,

kneeling or lying on the oor could force water through the oor fabric. To prevent this, do not pitch the

tent over hollows and make sure water drains away from the tent. You could also use a ground sheet

under the tent.

Structural integrity – A perfectly pitched tent on perfectly at, dry ground is structurally strong and most

waterproof. During prolonged wind and rain it may be necessary to tighten guy lines and reset the tent

pegs to prevent the y from sagging or apping and attend to drainage around the perimeter of the tent.

Sagging and incorrect pitching weakens the tent structure and could allow water to pool on the y placing

undue forces on the tent causing leaking and breakages.

IMPORTANT

1.This tent is designed as a recreational product only and is not suitable for

use as a dwelling.

2. During rain always lower awnings to avoid water ponding on awnings

3. Never store a wet and/or soiled tent, as mildew and corrosion will form

within a few days. This condition is not covered by warranty. Always allow

tent to dry completely before packing and stowing.

4. Elastic shock cord is provided to assist in the quick and easy assembly of

the poles. Age, over stretching and mishandling will cause failure. Shock

cord is not covered by warranty.

5. Your tent is valuable and should be insured against loss or damage.

6. During strong winds and storms collapse the tent at onto the ground and

seek refuge in your vehicle. Damage caused by storms and strong winds is

not covered by warranty.

WARRANTY

OZtrail tents are warranted for a period of two years from date of purchase. The

manufacturer agrees during the warranty period to repair any manufacturing

defects in the product or, at its option, replace the product with another product or

an equivalent product without cost to the owner for material or labour.

This warranty is subject to the original proof of purchase and the products being

used in accordance with the instruction manual.

Important: This tent is to be assembled once before going camping to ensure

that all parts are present and to become familiar with the assembly of the tent.

This warranty does not cover defects due to modication, accident, damage

caused by vandalism, rusting, acts of nature or any other event beyond the

control of the manufacturer. Nor does this warranty cover scratching, scufng,

natural breakdown of materials that occur inevitably with extended use including

Ultra Violet light damage and exhausted zippers or other cosmetic damage

that may result from normal wear and tear. In addition, defects resulting from

intentional damage, negligence or unreasonable use will void this warranty.

If the product is defective within the terms of this warranty, OZtrail will repair or

replace defective parts at no cost to the purchaser. Please note the shipping

charges to and from the OZtrail warehouse or original place of purchase are

not covered under warranty and are the responsibility of the purchaser. OZtrail

reserves the right to make substitutions to warranty claims if parts are unavailable

or obsolete.

This warranty does not cover incidental expenses including property damage.

REPLACEMENT PARTS

Please note, weights measurements are approximate only. Due to our Policy of

continual product development, speciﬁcations and features may vary from time to time.

Ring & pi n

Main Pole

MODEL #OLT-BAC-07

PARTS LIST

1 x Duraluminum poles complete

14 x Alloy pegs

2 x Guy ropes

1 x Fly sheet

1 x Tent bag

1 x Pole bag

1 x Peg bag

NB: Always menti on the Model Number in

all correspondence rega rding your tent.

PART N O . D ESCRIPTION

OLT-BAC-LP07 Long shock-corded pole

OLT-BAC-FLY07 Polyester UVTex 68D Ripstop 3000mm Fly

MP-RPS Ring & pin single

OLT-BAC-CB07 Tent carry bag

BACKPACKER

ASSEMBLY INSTRUCTIONS :

IMPORTANT: It is advisable to assemble the tent once before going camping to ensure

that all parts are present and to become familiar with the assembly of the tent.

Step 1 - Lay out the tent

Select a sheltered camp site protected from the wind that will not allow water to pond under the tent ﬂoor.

Clear a level area of all stones, twigs, etc.

Lay out tent with doors facing the desired direction.

Open doors to allow air inside when standing tent up.

Join the duraluminum poles together ensuring each section is firmly secured into the next.

Step 2 - Install the poles

- Slide the assembled pole through the sleeve in the tent (see figure 3). Gently raise the tent and place the

end of the pole onto the pin (see figure 2 ). The tent should stand up during this action (see figure 3).

WARNING: Do not force pole through the sleeves as this may damage the sleeve and could break the pole.

Check to ensure the pole does not snag when sliding it through the sleeve.

Step 3 - Peg down the tent

Peg the tent to the ground by driving pegs through the rings at the base of the poles.

Firm but not tight. Ensure all other peg down points are utilised.

Step 4 - Install the rain fly

Place the fly over the tent.

Secure fly by attaching the velcro inside the fly to the pole.

Attach the buckles on the fly to the tent at the base of the poles.

Peg down the remaining peg loops on fly sheet.

Peg out the guy ropes attached to the fly, peg out as far as possible from tent.

Ensure all peg down points are utilised and all guy ropes are attached ﬁrmly and remain ﬁrm (see ﬁgure 4).

Open side entrances on the fly as required.

Figure 2

Tent

Pole end

Figure 1

Figure 3

Figure 4

Please note, weights measurements are approximate only. Due to our Policy of

continual product development, speciﬁcations and features may vary from time to time.

The width of the tent

should not exceed the

length of the pole bag

Front of tent

(door unzipped)

Fo l d tent into a

Rectangular shape

ROLL

DISASSEMBLY INSTRUCTIONS

Release guy ropes. Release velcro that attaches the ﬂy to the poles.

Remove ﬂy from tent. Lay ﬂy ﬂat on ground and fold the ﬂy in half, third or quarters.

(folding depends on the length of the pole carry bag.)

Unzip doors and windows and collapse the tent, removing and disassembling the poles.

Place the poles in the pole carry bag and tie shut.

Remove pegs. Do not remove pegs from the ground by pulling on peg loops.

This may cause the peg loops to tear out of the seam.

Spread the tent out ﬂat with all loose fabric within the edges of the tent base.

Try to ﬂatten the tent as much as possible.

Fold the tent in half, third or quarters. (folding depends on the length of the tent pole sections.)

Place the folded ﬂy in tent as you make the last fold.

Place the pole bag on back end of tent (trapped air is more easily forced out of the open door

when you are rolling up the tent.) The folded tent should be the width of the pole bag.

Beginning at the back end, roll your tent tightly around the pole bag, forcing out excess air as you

roll. Keep tent edges straight and pole bag centred as you roll.

When tent is rolled up, tie straps around it and place into tent carry bag with peg bag, instruction

sheet, and other miscellaneous parts. If tent won’t ﬁt into bag, unroll and reroll more tightly.

Thank you for purchasing a superior quality

Outer Limits tent. This trouble shooting guide

is designed to give you years of fun &

enjoyment from your camping equipment.

HELPFUL HINTS GUIDE

Condensation - this is caused by lower temperatures on the outside of the tent combined

with body heat on the inside of the tent. When this occurs, avoid touching walls to reduce contact

leakage. Leaving the doors and windows open will reduce moisture condensation.

Seam leakage - all Outer Limits tents are manufactured by expert machinists.

However, seepage may occur in the seams through the needle holes created in the sewing process.

This is normal and can be corrected by applying a generous amount of seam sealer or wax on the

inside of the seams. Seam sealer is available at all retail camping specialists.

Mildew - to avoid mildew, never put your tent away wet or damp. However, if mildew occurs, use a

soft bristle brush or sponge with mild detergent to clean. Let the tent dry in the sunlight and re-apply

seam sealer compound on the inside of the seams.

Repairing a tear - for small tears, use a self-adhesive patch kit. We recommend a canvas

or awning repairer for larger tears.

Faulty zipper - all our tents are manufactured with zippers which, if the zipper separates, you

can ﬁx the zipper by moving the slider to the beginning of the zipper tape and reworking the zipper. If

this doesn’t work, we recommend you visit a canvas or awning repairer in your area.

Fading fabric - do not leave your tent set up in direct sunlight longer than is necessary. If left

in sunlight for prolonged periods of time, fabric will fade and weaken.

Floor condensation - a ground sheet under the tent prevents the ﬂoor from feeling damp

and helps prolong its life. The ground sheet should be smaller than the tent’s ﬂoor to prevent rain

from running under the tent.

Shock cord failure - spring and elastic shock cord is provided to assist tent assembly. Age,

over stretching and mishandling pole assembly will cause elastic failure. Elastic shock cord is delicate

and should be handled with care.

Removing pegs - pegs should be pulled with another peg, hammer or a peg puller, never

by pulling on the tent. Avoid pegging tent so tight that it stretches the fabric. Overstretching may

cause peg loops to tear.

Inhaltsverzeichnis

Andere Outer Limits Zelt Handbücher

Outer Limits

Outer Limits Starlite Bedienungsanleitung

Beliebte Zelt Handbücher anderer Marken

OZTENT

OZTENT JV SIGNATURE EDITION Bedienungsanleitung

GigaTent

GigaTent Summer Chalet Mini Tent Bedienungsanleitung

Coleman

Coleman 2000007827 Handbuch

ShelterLogic

ShelterLogic 107153 Bedienungsanleitung

Outsunny

Outsunny 84C-230 Bedienungsanleitung

Napier

Napier SPORTZ COVE 61 Series Bedienungsanleitung

EuroTrail

EuroTrail ATLANTIS PRO Bedienungsanleitung

Reimo

Reimo Marina Bedienungsanleitung

TiiTENT

TiiTENT TB300 Bedienungsanleitung

Coleman

Coleman 2000033134 Installationsanleitung

Ozark Trail

Ozark Trail W784.1 Kurzanleitung

SlingFin

SlingFin CrossBow 2 Bedienungsanleitung

Coleman

Coleman 9600-141 Bedienungsanleitung

Palram

Palram Arizona 5000 Wave - WINGS Bedienungsanleitung

COVERPRO

COVERPRO 56184 Montageanleitung

Vango

Vango Zenith 100 Bedienungsanleitung

Costway

Costway PATIOJOY OP70818 Bedienungsanleitung

Clarke

Clarke PUC 88 Bedienungsanleitung