Output Solutions KP-200 Bedienungsanleitung

1. DIAGRAM FOR SET UP..................................................................1

2. INTRODUCTION..............................................................................1

3. POWER ON SEQUENCE.................................................................1

4. EDIT MODE OPERATION..............................................................2

5. PRINT MODE OPERATION.........................................................10

6. ERASE FORMAT............................................................................11

7. ERASE ALL FORMAT ...................................................................11

8. SPECIAL FEATURES OPERATION ............................................12

Appendix A. Pin Assignment ................................................................12

Appendix B. Font Expansions ..............................................................14

1. DIAGRAM FOR SET UP

2. INTRODUCTION

The KP-200 Stand-alone keyboard control Terminal supports four types of operation.

a. EDIT MODE OPERATION.

The operator can design or edit label formats by themselves. The label formats can be

stored in an interchangeable memory module. A maximum of eight formats may be

stored in each nterchangeable memory module.

b. PRINT MODE OPERATION.

Print the restored label format on the EZ-2 or EZ-4 Thermal Printer.

c. ERASE MODE OPERATION.

Delete an individual label format.

d. ERASE ALL MODE OPERATION.

Erase entire contents of interchangeable memory module.

3. POWER ON SEQUENCE

ConnecttheKP-200keyboardtothe EZ-2 or EZ-4 9 pin RS232 port with the interface

cable provided.

Power on the printer display show Product name and Version number. The LCD

display will show: GODEX

KP-200 VER 1.0

After approximately 2 seconds the LCD will change to display the four types of

operation. The LCD display will show:

[1] EDIT MODE

[2] PRINT MODE ?

There are four operation modes (as described in the introduction) that may be selected.

The keyboard operator can select the desired mode of operation by highlighting it with

the cursor keys and then pressing

ENTER” or

Press 1 to select EDIT MODE.

Press 2 to select PRINT MODE.

Press 3 to select ERASE FORM.

Press 4 to select ERASE ALL.

4. EDIT MODE OPERATION

Edit mode operation allows the keyboard operator to design new label format or edit

current ones.

Pressing 1or ENTER when Edit mode is highlighted will begin the Edit mode

sequence.

(A) RESTORE FORMAT FROM MEMORY MODULE.

If a label format has previously been saved in the memory module, the LCD display

will show:

RESTORE FORM(Y/N)

Enter N and the keyboard will automatically step to (B).

Enter Yand the LCD display will show:

ENTER FORM NAME:

LAB1

Let us assume thatLAB1 is the name of the first label format. You may use the cursor

keys to highlight previously formats of you may type in the format name if known.

Press ENTER and the keyboard will load the requested format from the memory

module. The LCD display will show:

WAIT FOR LOADING

>>.................................<<

(B) SELECT PRINTER TYPE.

The LCD display will show:

SELECT PRINTER TYPE.

2” PRINTER 4” PRINTER

You may use the cursor keys to highlight the desired printer type or you may key in 2 to

select the EZ-2 or 4 to select the EZ-4. Press ENTER to accept your selection.

The LCD display will show:

SELECT PAPER TYPE:

Label , Blkmrk , Fax

Label -Self adhesive label with gap mounted on backing sheet.

Blkmrk -Registration mark on underside of media.

Fax -Continuous media with no registration mark.

Youmayusethecursorkeystohighlightthedesired media type of by typing in the first

letter of the required media (L. B. or F.). PressENTER to accept your selection.

(D) ENTER LABEL HEIGHT.

LCD display will show:

ENTER LABEL WIDTH

Enter label width in mm. PressENTER toacceptyourselection. If you selected Fax in

the previous menu, the keyboard will automatically step to (H), otherwise proceed to

next menu (E).

(E) ENTER LABEL HEIGHT.

LCD display will show:

ENTER LABEL HEIGHT

Enter label height in mm. PressENTER to accept your selection. If you selected label

at step (C), the keyboard will automatically step to (I), otherwise proceed with next

menu.

Note:Label height includes label length + gap.

Example: Labellengthis 25mm, Gap widthis3mm, then theLABEL HEIGHT will be

28mm

Label height in black mark label is defined as follows:

(a) The distance between tear line to next tear line.

(b) The distance Between Black mark (including itself).

lebelheight

(F) ENTER TOP LENGTH

LCD display will show:

ENTER TOP LENGTH

The TOP LENGTH is defined as follows: X will be the distance from the edge of the

black registration mark to the next tear line along the paper feed axis.

(1) IfXis less than 46mm, and the tear line is outside the black registration mark then

top length is X.

paperfeed

tearline

(2) If Tear line is inside Black registration mark then TOP LENGTH = -X.

paperfeed

tearline

(3)If Xis greater than 46mm, and the Tear line is outside the Black registration mark

then TOP LENGTH= Label height -X.

paperfeed

(G) ENTER BLACK LENGTH

The diagram of BLACK LENGTH is defined as follow: tearline

blacklength

The BLACK LENGTH in millimeters, then press “ENTER” key, KP-200 will go to

step(I).

(H) ENTER FEED LENGTH FOR FAX PAPER.

LCD display will show:

FEED LENGTH(1~25mm)

Enter Feed Length in mm and pressENTER to accept your selection.

(I) ENTER PRINT SPEED

LCD display will show:

SPEED 1 TO 2

Enter desired Print speed.

1is equal to 1“ per second.

2is equal to 2“ per second.

Press ENTER to accept your selection.

NOTE: 2“ per second is the default value.

(J) ENTER THERMAL HEAD

TEMPERATURE (DARKNESS)

LCD display will show:

DARKNESS 0 TO 7

Enter 0 to 7 (light to Dark), and press ENTER to accept your selection.

NOTE: Default value is 5.

(K) SELECT SELF STRIP FUNCTION.

LCD display will show:

SELF –STRIP (Y/N)?

If your printer has the stripper option, you can enter Yto enable the stripper sensor.

Press ENTER to accept your selection.

NOTE: Default value is N.

(L) FIELD PROGRAMMING.

LCD display will show:

FIELD 1:

The maximum number of fields available on one label format is eighteen. If the label

format has been restored form the memory module, you may usethe cursor keys to

select the field you wish to edit and then press ENTER. If this is to be a new label

format just press ENTER.

(M) ENTER DATA TYPE.

LCD display will show:

SELECT TEXT/BARCODE

[Shift]+[NUMERICAL]

Hold down the Shift key and press the 0 key to select the TEXT field.

Hold down the Shift key and press the 1 key to select the CODE 39 barcode field.

Hold down the Shift key and press the 2 key to select the CODE 93 barcode field.

Hold down the Shift key and press the 3 key to select the CODE 128 barcode field.

Hold down the Shift key and press the 4key to select the CODABAR barcode field.

Hold down the Shift key and press the 5key to select the INTERLEAVED 2 OF 5

barcode field.

Hold down the Shift key and press the 6 key to select the POSTNET barcode field.

Hold down the Shift key and press the 7 key to select the AN8 barcode field.

Hold down the Shift key and press the 8 key to select the EAN13 barcode field.

Hold down the Shift key and press the 9 key to select the UPC barcode field.

(N) ENTER BLANK LINE.

The LCD display will show:

LINE SPACE? (0~99 mm)

Line space is defined as the distance from this field to the next in mm. Enter desired

dimension (0~99mm) and pressENTER to accept your selection.

NOTE: Default value is 0.

(O) VARIABLE FIELD?

The LCD display will show:

VARIABLE (Y/N)?

For variable data press Y. For fixed data press N.

NOTE: Default value is Y.

(P) FONT SIZE.

1. Horizontal multiplier. The LCD display will show:

ENTER X SIZE(1~4)

Enter horizontal multiplier (1~4). Press ENTER to accept your selection.

2. Vertical multiplier. The LCD display will show:

ENTER Y SIZE(1~7)

Enter vertical multiplier (1~7). Press ENTER to accept your selection.

NOTE: The default value in both case is 1.

3. Enter Text Data. The LCD display will show:

ENTER DATA :

Enter the Text data and press ENTER.

(Q) BARCODE DATA FIELD.

1. Narrow bar ratio. The LCD display will show:

NARROW (2 TO 4)

Enter narrow bar to width in dots.(2 to 4).

Press ENTER to accept your selection.

NOTE: The default value is 2.

2. Wide bar ratio. The LCD display will show:

WIDE(4 TO 12)

Enter wide bar width in dots(4 to 12) Press ENTER to accept your selection.

NOTE: The default value is 5.

3. Barcode height. The LCD display will show:

HEIGHT (1 TO 7)

Enter Barcode Height(1 to 7). Press ENTER to accept your selection.

NOTE: The default value is 3.

4. Human Readable. The LCD display will show:

READABLE(Y/N)

Enter Y and human readable is enabled. Enter N and human readable is disabled.

Press ENTER to accept your selection.

NOTE: The default value is Y.

5. Enter Barcode. The LCD display will show:

ENTER DATA:

Enter the Barcode data and press ENTER to accept your selection. The keyboard

will automatically revert to menu K.

(R) SAVE FORMAT TO MEMORY CARD.

The LCD display will show:

SAVE FORM(Y/N)

Enter N-Keyboard will automatically step to next field.

Enter Y-LCD display will show:

Enter form name:

You can enter a maximum of sixteen characters to define a label name. Press

ENTER to save your format to the memory module.

(S) HOW TO SET UP DATA FIELD AS A VARIABLE.

1. If the data field is to be a variable, then the LCD display will show:

DATA LENGTH?(1~34)

A variable field allows the operator to input variable field data while the keyboard is in

the PRINT MODE enter DATA LENGTH(1~34, Dependent upon Font size & Label

width).

Press ENTER to accept your selection.

2. The LCD display will show:

ENTER X SIZE(1-4)

Same procedure as (P). Press ENTER to

accept your selection.

3. The LCD display will show:

ENTER Y SIZE(1-7)

Same procedure as (P). Press ENTER to accept your selection.

4. The LCD display will show:

POSITION OR PRESS D ?

Press “Shift”+“TAB1” Add one space in front of data.

Press “Shift”+“TAB2” Add eight spaces in front of data.

Press “&” This field and next field will be the same line.

Press “Shift”+“INS/L” To insert a field.

Press “Shift”+“DEL/L” To delete this field.

Press Dto step to next screen.

5. The LCD display will show:

POSITION OR PRESS D ?

•••••••

Theboxesdisplayed represent character fieldstoindicate to the operatorthelength(in

characters) of the variable data.

Example: Ifthedata length is5,LCD will show 5blocks.Ifthe data length is 3, LCD will

show 3 blocks. Press ENTER to proceed to next menu.

Inhaltsverzeichnis

Andere Output Solutions Touch-Terminal Handbücher

Output Solutions

Output Solutions KP-180 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung