Overland Storage SnapServerXSR 40 Bedienungsanleitung

*10400560-002*

SnapServer®XSR40

Add-on/Spare PCIe Card Instructions

This document describes how to remove and replace a PCIe

card in a SnapServer XSR40 from Overland-Tandberg.

WARNING: To reduce the risk of electric shock or damage to

equipment, always remove any power cords while working with

the unit.

WARNUNG: Um das Risiko eines elektrischen Schlags oder

Schäden am Gerät zu vermeiden, ziehen Sie stets den

Netzstecker, bevor Sie an der Einheit arbeiten.

AVERTISSEMENT: Pour réduire le risque de choc électrique

ou endommagement de l'équipement, retirez toujours les

cordons électriques en travaillant avec l'appareil.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ESD) precautions to prevent damage

to micro-circuitry or static-sensitive devices. NOTE: The Spare may come without the mounting bracket.

Reuse the existing bracket.

Prepare the Unit

It is essential that you activate your warranty. Technical and

warranty support is not available until you are registered.

For an existing customer:

1. Go to http://support.overlandstorage.com/ support page.

2. Enter your e-mail address and password, and press

Enter or click the right arrow (>).

3. Click Register New Product.

4. Fill in the information (including serial number) and

click Submit.

Your warranty certificate will be emailed to you. Follow

the instructions in the email to complete the process.

For an existing customer, go to Register a Product and follow

the instructions.

Existing Customer Login

New Customer Registration

Power Off and Disconnect

If the unit is still running, power it down cleanly:

1. Use the Web Management Interface to shut down the

server (Maintenance > Reboot and Shutdown >

Shutdown).

2. When all the LEDs are off, disconnect the power cords.

3. Disconnect the remaining cables from the unit.

EnterEnter

Enter

All Fields

SnapServer XSR40 Add-on/Spare PCIe Card

Remove the Front Bezel

1. Carefully take hold of the front bezel by the right and

left flanges and pull straight out from the appliance until

the retaining clips release.

2. Set the bezel aside on a secure surface.

Remove the Drives

IMPORTANT: Overland recommends that you remove the disk

drives to reduce the unit’s weight prior to removal. They must

be replaced in the same drive bays when done.

Remove all the drive and blank carriers, and note from which

bay each was removed.

NOTE: Do not remove the disk drives from their carriers. Doing so

voids the drive warranty.

1. Press the release button on the right side of the carrier.

2. Using the built-in handle, pull the carrier out.

3. Number the carrier and set it on a secure surface

4. Repeat Steps 1–3 for all the remaining carriers.

Remove Unit from Rack

WARNING: It is recommended that a mechanical lifter (or at

least two people) be used during rack installation or removal to

prevent injury.

WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir

zur Rack-Installation oder -Deinstallation die Nutzung einer

mechanischen Hebehilfe (oder mindestens zwei Personen).

AVERTISSEMENT: Pour éviter toute blessure il est

recommande qu'un monte-charge (ou deux personnes au

moins) soit utilisé lors de l'installation ou de l'enlèvement du

support.

1. Based on the mounting system, carefully remove the

appliance from the rack as follows:

• Fixed brackets: With a lifter positioned in front of the

array, release the four screws and the slip nuts from

the front flanges, and slide the chassis out onto the

lifter.

• Sliding rails: With a lifter positioned in front of the

array, release the screws, release the rail locks, and

slide the chassis out onto the lifter.

2. Move the chassis onto a secure surface.

Pull Pull

1 2 3 4

Press

Pull Handle

Sliding Rails

SnapServer XSR40 Add-on/Spare PCIe Card

Install/Replace the PCIe Card

Remove the Top Panel

1. Loosen the two captive screws at the rear of the top

panel that secure it.

2. Slide the panel toward the rear about one-half inch

(1.25cm).

3. Lift the panel off and set it aside.

Remove the PCIe Card/Access Cover

1. Remove and retain the two screws securing the locking

bracket to the PCIe slot.

2. Remove and retain the locking bracket.

3. Do one of the following:

•Remove the PCIe card from the slot on the board and

set aside on an ESD surface. Continue with Swap the

Mounting Bracket.

•Remove the Access Cover from the rear panel opening

and set it aside. Continue with Install the PCIe Card.

Swap the Mounting Bracket

1. Remove and retain the two screws securing the

mounting bracket to the old PCIe card.

2. Remove the mounting bracket from the old card and

position it on the new card.

3. Using the retained screws, secure the bracket to the

new PCIe card.

Install the PCIe Card

1. Seat the PCIe card in the same slot on the board with the

card aligned in the rear panel opening.

2. Reinstall the locking bracket and, using the retained

screws, secure the PCIe card.

Reinstall the Top Panel

1. Position the top panel with no more than one-half inch

(1.25cm) extending out over the rear of the unit.

2. Slide the panel forward until it is fully seated.

3. Using the two captive screws on the rear of the top

panel, secure it.

2 Screws

On Back

Remove Screws

PCIe Card

Remove Screws

2 Screws

On Back

SnapServer XSR40 Add-on/Spare PCIe Card

Reinstall Chassis in Rack

Reinstall the Chassis

1. Using the mechanical lifter, position the chassis in front

of the appliance’s existing rack rails.

2. Based on the mounting system, carefully insert the unit

into the rack and secure it:

• Fixed brackets: Position the unit in the rack and use

the four retained screws, including slip nuts, to

secure the front flanges to the rack.

• Sliding rails: Slide the side rails into the rack rails,

slide the unit all the way to the rear, then secure the

unit using the screws on the front flanges.

Reinstall the Drives

Return the drive assemblies back to their original bays.

1. Position the drive assembly in front of its bay.

2. Slide it in until the latch closes, locking the assembly in

the bay.

3. Repeat Steps 1–2 for each remaining drive assembly.

IMPORTANT: To maintain proper airflow and cooling, a drive

assembly or a blank carrier must be installed in every bay. No

empty bays are allowed.

Reattach Cables and Power Cords

1. Reattach all cables to the same connections as before.

2. Attach the power cord.

3. At the front of the appliance, press the power switch to

power it ON.

Reattach the Bezel

1. Position the bezel with the top and bottom edges aligned

with the slots on the front of the appliance.

2. Push the bezel onto the unit until the retaining clips latch

and the bezel snaps into place.

3. Verify that the bezel is aligned properly and that all the

LEDs are visible.

Return Old Parts to Overland

1. Place any old parts in the anti-static bag and put them in

the replacements’ box.

2. Use the existing packing materials to secure them in

the box.

3. Use an RMA to return the parts to Overland-Tandberg.

For return shipping details and RMA number, go to:

http://docs.overlandstorage.com/return-instructions

Slide Carrier

Power Socket

Cable Ports

Retaining Clip

Andere Handbücher für SnapServerXSR 40

Inhaltsverzeichnis

Andere Overland Storage Server Handbücher

Overland Storage

Overland Storage SnapServer N2000 Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S1000 Bedienungsanleitung

Overland Storage

Overland Storage Snap Server 18000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer 2U Appliance Leitfaden

Overland Storage

Overland Storage SnapServer 510 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer Service-Handbuch

Overland Storage

Overland Storage Snap Server 12000 Bedienungsanleitung

Overland Storage

Overland Storage ARCvault Series Bedienungsanleitung

Overland Storage

Overland Storage SnapServer Expansion E2000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer DX2 Leitfaden

Overland Storage

Overland Storage Snap Server 14000 Bedienungsanleitung

Overland Storage

Overland Storage SnapScale Service-Handbuch

Overland Storage

Overland Storage SnapServerXSR 40 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer XSR 120 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer DX1 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer Service-Handbuch

Overland Storage

Overland Storage SnapServer 110 Bedienungsanleitung

Overland Storage

Overland Storage Snapshot SnapSAN Bedienungsanleitung

Overland Storage

Overland Storage SnapServer XSR 120 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer 210 Bedienungsanleitung

Overland Storage

Overland Storage Snap Server 18000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer DX1 Bedienungsanleitung

Overland Storage

Overland Storage ARCvault Series Bedienungsanleitung

Overland Storage

Overland Storage snap server 410 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung