Overland Storage ARCvault Series Bedienungsanleitung

IMPORTANT: Overland Storage requires that ARCvault

parts be removed and replaced by an Overland Storage

authorized service provider. Improper installation may

result in damage which voids existing warranties.

This document describes how to remove and replace a

Shuttle assembly in an Overland ARCvault Series library.

WARNING: To reduce the risk of electric shock or

damage to equipment, disconnect the power by

unplugging the power cord.

WARNING: It is recommended that a mechanical

lifter (or at least two people) be used to prevent

injury during rack removal and reinsertion.

CAUTION: Be sure all screws and washers are accounted for

during this procedure. A loose object can cause the library not

to function.

CAUTION: Do not over-torque the shuttle carriage screws when

installing the new shuttle! Use only 2-3 IN LB of torque.

Unpacking

Carefully unpack and verify that you have all the parts:

•Shuttle assembly

•Two 4-20x5/16 screws

•Four M2x4mm screws

•These remove & replace instructions

In addition, you will need a #1 magnetic Phillips

screwdriver. You may also need the Magazine Removal

Tool (MRT) from the Accessory Kit (or equivalent).

IMPORTANT: If the shuttle still contains a tape cartridge,

contact Overland Technical Support for information on

removing it.

Electrostatic Discharge Information

To help prevent Electrostatic Discharge (ESD) damage,

observe these and other standard ESD precautions:

•Use a wrist strap and properly-grounded tools.

•Make sure you are always properly grounded.

•Avoid touching pins, leads, or circuitry.

Remove Magazines

To lower the weight of the unit, remove the magazines

before removing the unit from the rack.

CAUTION: Keep a loaded magazine level. Tilting the magazine

can result in the tapes falling out. Also, don’t hold a magazine

by just the handle; use both hands to support it.

NOTE: If unable to power up the library, refer to the ARCvault

user guide for instructions on removing magazines manually.

1. Press Utilities > Service > Access All Mags > OK (at

the going offline message) > Unlock All.

2. Open the doors and remove all the magazines.

3. Close the doors.

4. Press Relock All and OK at the removal message.

5. Press Back three times.

6. Press Power > Power Off Library > OK (at the

power down message) to power down the unit.

Remove Unit from Rack

1. At the rear, remove the power cord and all cables.

2. At the front, loosen the retaining screws inside the

front doors.

3. Using either a mechanical lifter or at least two people,

remove the ARCvault unit from the rack and place it

on a secure, flat surface.

ARCvault Series

Shuttle Assembly Spare

Remove & Replace Instructions

Overview & Notes

ARC-0111

Preparing the Library

Remove Old Shuttle Assembly

1. Remove the front top cover, retaining the screws.

2. Using a magnetic #1 Phillips screwdriver, remove the

four screws (Figure 1) holding the shuttle assembly

to the shuttle carriage.

Figure 1. Shuttle Screw Locations

3. Carefully remove the two screws holding the cable

bracket to the rear of the shuttle.

4. Unplug the Bar Code Reader and Picker Motor

cables from their sockets (Figure 2).

To remove them, press the release tabs on the outside

of the plugs and pull gently.

5. Set aside the old shuttle assembly.

Figure 2. Cables Connections on Shuttle

6. Using your finger, roll the top of the coupling tube

AWAY from the front panel to move the shuttle

carriage toward the center of the track plate.

Move it out at least 1 inch (2.5cm) for easier access.

Figure 3. Coupling Tube Location

Removing the Old Shuttle Assembly

ARC-0113

Remove Cable Bracket

ARC-0112

Picker Motor Bar Code Reader

Cable Socket Cable Socket

Bracket

Screw Holes

ARC-0132

Coupling Tube Shuttle Motor

Rear Gear Assembly

1. Plug the Bar Code Reader and Picker Motor cables

into their sockets on the new shuttle assembly.

2. Using two new 4-20x5/16 screws, reattach the cable

bracket to the new shuttle.

3. Using the alignment ribs (Figure 4), position the

shuttle over the carriage assembly on the track plate.

4. Lower the shuttle onto the carriage plate, aligning the

four holes.

Figure 4. Alignment of Shuttle to Track Plate

5. Very gently, using four new M2x4mm screws, attach

the shuttle assembly to the shuttle carriage.

IMPORTANT: With the screw on the end of the

magnetic screwdriver, guide it down the hole to the

carriage assembly. Tighten to no more than 2-3 IN LB.

6. Using the retained screws, reattach the front top

cover.

Reactivate the Library

1. Return the library into rack.

2. Tighten the retaining screws on the front.

3. Reinsert the media magazines and close the doors.

4. At the rear, reattach all network cables.

5. Plug in the power cord and power on the unit.

6. Verify that the POST inventory passes to confirm the

functionality of the new shuttle.

Installing the New Shuttle Assembly

ARC-0135

ARC-0130

Alignment Ribs

Shuttle Carriage

Shuttle

Coupling Tube

Shuttle (Bottom View)

All information contained in or disclosed by this document is considered proprietary by Overland Storage. By accepting this material, the recipient agrees that this material and the information contained

therein are held in confidence and in trust and will not be used, reproduced in whole or in part, nor its contents revealed to others, except to meet the purpose for which it was delivered. It is understood that

no right is conveyed to reproduce or have reproduced any item herein disclosed without express permission from Overland Storage. Overland Storage provides this document as is, without warranty of any

kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Overland Storage may make improvements or changes in the

product(s) or program(s) described in this document at any time. These changes will be incorporated in new editions of this publication.

Overland Storage assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this document, nor for any problem that might arise from the use of the information in this document.

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com,

or call 1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or

+1 (858) 571-5555 Option 5 (International).

Andere Handbücher für ARCvault Series

Inhaltsverzeichnis

Andere Overland Storage Lagerung Handbücher

Overland Storage

Overland Storage NEO 2000e Bedienungsanleitung

Overland Storage

Overland Storage NEOs T24 Bedienungsanleitung

Overland Storage

Overland Storage NEO 2000e Bedienungsanleitung

Overland Storage

Overland Storage REO 4500x Bedienungsanleitung

Overland Storage

Overland Storage NEO XL Series Bedienungsanleitung

Overland Storage

Overland Storage Neo Series 2000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer DX1 Bedienungsanleitung

Overland Storage

Overland Storage NEO 8000E Bedienungsanleitung

Overland Storage

Overland Storage NEO 8000 Bedienungsanleitung

Overland Storage

Overland Storage Neo Series Library Bedienungsanleitung

Overland Storage

Overland Storage NEO 2000e Bedienungsanleitung

Overland Storage

Overland Storage REO 4600 Bedienungsanleitung

Overland Storage

Overland Storage PowerLoader Bedienungsanleitung

Overland Storage

Overland Storage NEO 8000E Bedienungsanleitung

Overland Storage

Overland Storage SnapServer Service-Handbuch

Overland Storage

Overland Storage REO 1000 Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S5000 Bedienungsanleitung

Overland Storage

Overland Storage SnapServer Bedienungsanleitung

Overland Storage

Overland Storage Tandberg Data RDX QuikStor Bedienungsanleitung

Overland Storage

Overland Storage SnapScale X4 Node Leitfaden

Overland Storage

Overland Storage SnapServer XSD 40 Bedienungsanleitung

Overland Storage

Overland Storage LoaderXpress Leitfaden

Overland Storage

Overland Storage NEO 8000 Bedienungsanleitung

Overland Storage

Overland Storage NEO S-Series Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung