OWC ThunderBay 4 Leitfaden

2.5" & 3.5"

HDDs & SSDs

Mac & Windows4-Bay RAID Array Thunderbolt 2

Assembly Manual & User Guide

ThunderBay 4

OWC ThunderBay 4 Contents

Introduction

1.1 Minimum System Requirements.............................................. 1

-Mac Requirements

-PC Requirements

-Supported Drives

1.2 Package Contents..................................................................... 1

1.3 About This Manual.................................................................... 1

1.4 Front View.................................................................................. 2

1.5 Rear View................................................................................... 2

1.6 Usage Notes.............................................................................. 3

Device Setup

2.1 Hard Drive Installation .............................................................. 4

2.2 Quick Start................................................................................. 4

2.3 About SoftRAID ......................................................................... 5

2.4 Chaning Drives & Drive Failure ................................................. 5

Support Resources

3.1 Troubleshooting ........................................................................ 6

3.2 About Data Backup ................................................................... 6

3.3 Online Resources ...................................................................... 6

3.4 Contacting Technical Support.................................................. 6

CONTENTS

OWC ThunderBay 4 Introduction

1.1 Minimum System Requirements

Mac Requirements

-OS X 10.9.3–10.11.6; macOS 10.12 or later

-Any Mac with a Thunderbolt port

-Thunderbolt 2 port recommended for best performance

PC Requirements

-Windows 7 Service Pack 1 or later (Boot Camp is not supported)

-Any PC with a Thunderbolt port

-Thunderbolt 2 port recommended for best performance

Supported Drives

-Any 2.5-inch or 3.5-inch SATA drive

1.2 Package Contents

Drive mounting screws are included with empty enclosures, but not pictured.

Required tools: Phillips PH2 screwdriver

1.3 About This Manual

The images and descriptions may vary slightly between this manual and the unit shipped. Functions

and features may change depending on the rmware version. The latest product details and warranty

information can be found on the product web page. OWC’s Limited Warranty is not transferable and

subject to limitations.

INTRODUCTION

OWC ThunderBay 4

with Thunderbolt 2

Thunderbolt cable Power cable Security keys Quick start guide

Chat:M–F, 8am–8pm, Sat. 9am–5pm CT

www.owcdigital.com/support

Quick Start Guide

registeredinthe U.S. and/or other countries. Mac and macOS are trademarks of Apple Inc., registered in the United States and other countries. Thunderbolt

andtheThunderbolt logo are trademarks of Intel Corporation or its subsidiaries. Micr osoft and Windo ws are either regis tered trademarks o r trademarks of

MicrosoftCor poration in the Un ited States and/or ot her countries . Other marks maybe the trademark or registered trademark property of their owners.

Phone:M–F, 8am–8pm CT

1.866.692.7100(N. America) | +1.815.338.4751 (Int’l)

Email:Answered within 48 hours

www.owcdigital.com/support

System Requirements

OperatingSystem:

–Mac: OS X 10.9.3–10.11.6;macOS 10.12 or later

–PC: Wi ndows 7 Service Pack 1 or later

–Bootcamp i s not supported

Hardware:

–Mac or PC wi th Thunderbolt 2 port

recommendedfor best performance

–Hosts with T hunderbolt ports sho uld also

workbut at s lower speeds

SupportedDrives:

–2.5 -inch and 3.5-inch S ATAdrives

PackageContents

–Thunde rBay 4 with Thunderbolt 2

–Thunderbolt cable

–Power supply and cable

–Security keys

–SoftR AID license

Installation & RAID Information

Fordetailed assembly steps, RAID information, and additional capabilities, the Assembly Manual &

UserGuide is available at: www.owcdigital.com/support/manuals

ContactingTechnical Support

ThunderBay 4

SoftRAID license

an OWC brand

OWC ThunderBay 4 Introduction

LED Color Power On Sleeping Drive

Activity

Drive Bad/

Bay Empty

Power Blue /

Amber

Solid blue with active

data connection Amber N/A N/A

Drive

(A, B, C, D) Green None Active None Active Flash

Green Not Active

1 2

1.4 Front View

1. Locking faceplate — Use the included keys to lock or

unlock and remove the faceplate.

2. LED indicators — See the chart below for LED details.

1.5 Rear View

1. Security slot — Connect a security tether here.

2. Thunderbolt 2 ports — Attach the included Thunderbolt

cable to one of these ports and to your computer, or to

another Thunderbolt device. Use the other Thunderbolt 2

port to add more Thunderbolt devices to the chain.

3. On/Off switch — Turn the power on and off using this

switch.

4. Power input — Connect the included power cable here.

OWC ThunderBay 4 Introduction

1.6 Usage Notes

-Although the ON/OFF switch controls power to the device, the OWC ThunderBay 4

requires an active data signal for powered operation. As long as the ON/OFF switch

is in the ‘ON’ position, the ThunderBay 4 will turn on when it receives a data signal

through the Thunderbolt cable. If there is no Thunderbolt cable connected, or if the

computer is off or in a sleep or hibernation mode, the ThunderBay 4 will turn off and

its power LED will turn orange to indicate that it is not receiving a data signal.

-In order to use any Thunderbolt devices chained through the ThunderBay 4, the ON/

OFF switch of the ThunderBay 4 must be in the ‘ON’ position.

-For the safe removal of your drives and to ensure that no data is lost, always

eject or unmount the drives from your operating system before unplugging the

ThunderBay 4 or removing the drives.

-Thunderbolt device chains can support up to six Thunderbolt devices.

-Thunderbolt 2 is backwards compatible with Thunderbolt, but any devices

connected in a Thunderbolt chain after a Thunderbolt device will operate at original

Thunderbolt speed (10Gb/s) rather than Thunderbolt 2 speed (20Gb/s). If mixing

Thunderbolt 2 and original Thunderbolt devices, make sure all Thunderbolt 2

devices are in front of the Thunderbolt devices (i.e. computer>Thunderbolt 2

devices>Thunderbolt devices).

OWC ThunderBay 4 Device Setup

If you purchased the ThunderBay 4 with drives, they have been installed prior to shipment — please

skip to Section 2.2, Step 4. If you are installing your own drives, follow the steps in Section 2.1 to install

3.5-inch hard drives into your ThunderBay 4 enclosure, or to replace existing 3.5-inch drives. Note: it is

possible to install 2.5-inch SATA drives using the ne-threaded screws that are included (16 in total),

and the four screw holes on the bottom of each drive tray (highlighted in step 5 below).

2.1 Hard Drive Installation

Follow these steps to install hard drives into your ThunderBay 4 enclosure, or to replace existing drives.

Repeat steps 1 through 8 as necessary for each drive you are installing.

1. Insert one of the included keys into the lock on the upper left of the faceplate.

2. Turn the key clockwise, then pull it towards you. The faceplate will swing open, as shown.

3. Once the faceplate has swung open as far as it will go, pull up to remove it.

4. On the drive tray you wish to remove, turn the thumbscrew counter-clockwise until you no

longer feel resistance. Then hold onto the thumbscrew and pull the drive tray out.

5. Set the drive tray as shown on your work surface. If you are replacing an existing hard

drive, unscrew it from the drive tray at this time. NOTE: the highlighted screw holes are for

2.5-inch drives. The holes for 3.5-inch drives are highlighted in green (Step 7).

6. Place the hard drive inside the drive tray as shown. The label should face up and the SATA

connectors should be on the far rear corner of the drive.

7. Fasten the drive into the drive tray using six of the included screws (three per side).

8. Slide the drive tray back into the rails in the ThunderBay 4 and push until it is seated

fully, then push in on the thumbscrew and turn it clockwise until it stops turning. If you

encounter resistance, do not force the drive tray. Remove it, check to make sure that there

are no obstructions and that the drive tray is lined up correctly, then slide it in again.

DEVICE SETUP

2 3 4

6 7 85

OWC ThunderBay 4 Device Setup

2.2 Quick Start

1. Install hard drives into the ThunderBay 4 according to the instructions in Section 2.1.

2. Connect the power cable to the enclosure and a power outlet, then make sure the ON/OFF

switch is set to the ‘ON’ position.

3. Connect a Thunderbolt cable between the ThunderBay 4 and a computer. When you do

this, the ThunderBay 4 will turn on and the drives will be available for use on the computer.

-NOTE: If you installed your own drives in the previous section, they need to be formatted

before you can use the ThunderBay 4. It shipped with a license for SoftRAID, which

is recommended for setting up RAID volumes and working with ThunderBays. If you

purchased your solution with drives, they were already formatted as a RAID volume, but you

should still install SoftRAID to get the best performance and functionality.

If you do not wish to use SoftRAID you can visit www.owcdigital.com/format and use one

of the Mac or PC specic links for instructions on formatting your drives.

2.3 About Software RAID

OWC ThunderBay 4 manages and protects your data with our advanced SoftRAID engine.SoftRAID

offers multiple RAID options (0, 1, 4, 5, 1+0), giving you the ability to set up your storage for speed, data

security or the best of both worlds. Packed with features from active predictive disk failure monitoring,

to multiple array volume spanning, SoftRAID from OWC brings technology typically found only in data

centers to your workstation or editing bay.

To learn more about SoftRAID please visit: www.softraid.com

2.4 Changing Drives & Drive Failure

You can add or remove any drive without needing to turn off the device or to unmount any of the other

drives. Each drive operates independently of the others and is not affected by the addition or removal

of another drive unless you set them up as members of a RAID array using software.

By itself, the ThunderBay 4 does not monitor drive health or alert you to a drive failure. You can monitor the

health of your drives via SoftRAID in order to determine when a drive has failed or is in a pre-failure state. To

replace a failed drive, simply remove the drive from its bay and replace it with another drive, following the

steps in Section 2.1. The ThunderBay 4 does not need to be turned off during this process.

OWC ThunderBay 4 Support Resources

3.1 Troubleshooting

Begin your troubleshooting by verifying that the power cable is connected to the ThunderBay 4 and to a

power source. If the power cable is connected to a power strip, make sure that the power switch on the

strip is turned on. Then, verify that both ends of your cables are properly plugged into the computer and the

ThunderBay 4.

If the ThunderBay 4 is still not working properly, try connecting to another computer or using another

Thunderbolt cable. Remember that the ThunderBay 4 needs an active data signal in order for the power

to remain on. If it is disconnected from the computer, or if the computer goes to sleep or turns off, the

ThunderBay 4 will go to sleep. If you are still experiencing problems, consult Section 3.4 for OWC technical

support contact information.

3.2 About Data Backup

To ensure that your les are protected and to prevent data loss, we strongly suggest that you keep two

copies of your data: one copy on your OWC ThunderBay 4 and a second copy on your internal drive or

another storage medium, such as an optical backup, or on a second external storage unit. Any data loss or

corruption while using the ThunderBay 4 is the sole responsibility of the user, and under no circumstances

may OWC, its parent, partners, aliates, ocers, employees, or agents be held liable for loss of the use of

data including compensation of any kind or recovery of the data.

3.3 Online Resources

To access our online knowledge base, please visit: www.owcdigital.com/faq

3.4 Contacting Technical Support

SUPPORT RESOURCES

Phone: M–F, 8am–8pm CT

1.866.692.7100 (N. America)

+1.815.338.4751 (Int’l)

Email: Answered within 48 hours

www.owcdigital.com/support

Chat: M–F, 8am–8pm, Sat. 9am–5pm CT

www.owcdigital.com/support

Changes:

The material in this document is for information purposes only and subject to change without notice. While

reasonable efforts have been made in the preparation of this document to assure its accuracy, OWC, its

parent, partners, aliates, ocers, employees, and agents assume no liability resulting from errors or

omissions in this document, or from the use of the information contained herein. OWC reserves the right

to make changes or revisions in the product design or the product manual without reservation and without

obligation to notify any person of such revisions and changes.

FCC Statement:

Warning! Modications not authorized by the manufacturer may void the user’s authority to operate this

device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference with radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

Health and Safety Precautions:

-Read this user guide carefully and follow the correct procedures when setting up the device.

-Use proper anti-static precautions while performing the installation of your hard drives into this

drive enclosure. Failure to do so can cause damage to your drive mechanisms and/or the hard

drive enclosure.

-Do not attempt to disassemble or modify the device. To avoid any risk of electrical shock, re,

short-circuiting or dangerous emissions, never insert any metallic object into the device. If it

appears to be malfunctioning, contact OWC technical support.

-Never expose your device to rain, or use it near water or in damp or wet conditions. Never place

objects containing liquids on the drive, as they may spill into its openings. Doing so increases the

risk of electrical shock, short-circuiting, re or personal injury.

General Use Precautions:

-Do not place objects on top of the device.

-To avoid damage, do not expose the device to temperatures outside the range of 5° C to 40° C

(41° F to 104° F).

-Always unplug the device from the electrical outlet if there is a risk of lightning or if it will be

unused for an extended period of time. Otherwise, there is an increased risk of electrical shock,

short-circuiting or re.

-Do not use the device near other electrical appliances such as televisions, radios or speakers.

Doing so may cause interference which will adversely affect the operation of the other products.

-Do not place the device near sources of magnetic interference, such as computer displays,

televisions or speakers. Magnetic interference can affect the operation and stability of hard

drives.

-Protect your device from excessive exposure to dust during use or storage. Dust can build up

inside the device, increasing the risk of damage or malfunction.

-Do not block any ventilation openings on the device. These help to keep the device cool during

operation. Blocking the ventilation openings may cause damage to the device and cause an

increased risk of short-circuiting or re.

Warranty:

The OWC ThunderBay 4 has up to a 5 Year OWC Limited Warranty. For up-to-date product and warranty

information, please visit the product web page.

Copyrights and Trademarks:

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by

any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent

of OWC.

Corporation, registered in the U.S. and/or other countries. Apple, Bootcamp, Mac, macOS, and OS X are trademarks of Apple Inc., registered in the

United States and other countries. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries. Microsoft and

Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Other marks may

be the trademark or registered trademark property of their owners.

OWCMANTB43TKY — 01/16/2020

Andere Handbücher für ThunderBay 4

Inhaltsverzeichnis

Andere OWC Lagerung Handbücher

OWC

OWC Mercury Elite Pro Dual Bedienungsanleitung

OWC

OWC Envoy Pro Bedienungsanleitung

OWC

OWC Mercury On-The-Go Pro Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual mini Leitfaden

OWC

OWC Mercury Accelsior Pro Q Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Leitfaden

OWC

OWC Envoy Gebrauchsanweisung

OWC

OWC ThunderBay 4 Leitfaden

OWC

OWC ThunderBay 4 mini Leitfaden

OWC

OWC Mercury Elite Pro Dual mini Leitfaden

OWC

OWC Mercury Helios Leitfaden

OWC

OWC Mercury Elite Pro Dual mini Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual mini Bedienungsanleitung

OWC

OWC Envoy Pro Bedienungsanleitung

OWC

OWC data doubler Leitfaden

OWC

OWC Mercury Elite-AL Pro "Quad Interface" Bedienungsanleitung

OWC

OWC Mercury Pro Leitfaden

OWC

OWC On-The-Go USB Bedienungsanleitung

OWC

OWC ThunderBay 4 Leitfaden

OWC

OWC OWC Elite Pro Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual Bedienungsanleitung

OWC

OWC Mercury Pro LTO Thunderbolt 3 Bedienungsanleitung

OWC

OWC Mercury Elite Pro Dual mini Leitfaden

OWC

OWC Mercury Elite-AL Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung