Oxgard Cube C-01 Bedienungsanleitung

Andere Handbücher für Cube C-01

2

Inhaltsverzeichnis

Andere Oxgard Drehkreuz Handbücher

Oxgard

Oxgard Praktika T-03-M Merkblatt

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

Oxgard

Oxgard Cube C-01 Merkblatt

Oxgard

Oxgard CUBE C-03 Technisches Datenblatt

Oxgard

Oxgard PRAKTIKA QL-04 Series Kurzanleitung

Oxgard

Oxgard CUBE C-03 Bedienungsanleitung

Oxgard

Oxgard Praktika T-10 Bedienungsanleitung

Oxgard

Oxgard CUBE C-04 Series Kurzanleitung

Oxgard

Oxgard Cube C-02 Merkblatt

Oxgard

Oxgard Praktika T-04 Bedienungsanleitung

Oxgard

Oxgard Praktika T-02 Bedienungsanleitung

Oxgard

Oxgard Praktika T-03-M Bedienungsanleitung

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

Oxgard

Oxgard Cube C-01 Kurzanleitung

Oxgard

Oxgard Praktika T-01 Merkblatt

Oxgard

Oxgard CUBE ?-04 Series Merkblatt

Oxgard

Oxgard CUBE C-04-s Bedienungsanleitung

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

Oxgard

Oxgard PRAKTIKA QL-04-SM-660 Merkblatt

Oxgard

Oxgard CUBE C-03 Bedienungsanleitung

Oxgard

Oxgard Praktika T-01 Bedienungsanleitung

Oxgard

Oxgard Praktika T-04K Kurzanleitung

Oxgard

Oxgard Praktika T-02 Merkblatt

Oxgard

Oxgard CUBE C-04-s Bedienungsanleitung

Beliebte Drehkreuz Handbücher anderer Marken

LBA GROUP

LBA GROUP LBAT10 Bedienungsanleitung

Magnetic

Magnetic mTripod Bedienungsanleitung

Kaba

Kaba Argus HSG-E02 Bedienungsanleitung

Automatic Systems

Automatic Systems TR491 Bedienungsanleitung

Turnstiles

Turnstiles HZ-SWGS01 Bedienungsanleitung

DSI

DSI DST-80 Bedienungsanleitung

OZAK

OZAK VP-125 Handbuch

Automatic Systems

Automatic Systems SMARTLANE SL 90X Bedienungsanleitung

Alvarado

Alvarado MT Montage- und Bedienungsanleitung

JKDC SECURITY

JKDC SECURITY JKDC-100C Bedienungsanleitung

Alvarado

Alvarado SU5000 Bedienungsanleitung

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Bedienungsanleitung

digicon

digicon CATRAX Plus Bedienungsanleitung

BOON EDAM

BOON EDAM Turnlock 100 Leitfaden

Wano

Wano Tripod BO-DSN10 Bedienungsanleitung

Timewatch

Timewatch TWLD-TS2700 Bedienungsanleitung

OZAK

OZAK GLASS LINE A1 Bedienungsanleitung

HZ Security

HZ Security HZ-SWBS02 Bedienungsanleitung

Maintenance

operations

www.oxgard.com

[email protected]

Tel. +7(812) 366-15-94

Cube С-01 turnstile

Technical Maintenance 3

CONTENTS

1. General instructions.................................................................................. 4

2. Conditions for performance of technical maintenance............................ 5

3. Partial disassembly of the turnstile .......................................................... 5

4. Checking turnstile assemblies................................................................ 11

5. Lubricating sliding parts of turnstile mechanisms................................. 11

6. Assembly and functionality test of the turnstile .................................... 14

Cube С-01 turnstile 4

1. General instructions

1.1. During operation of the turnstile in order to maintain efficiency and to

ensure calculated lifetime the maintenance operation of the turnstile shall

be carried out periodically, including the warranty period (hereinafter

MO).

1.2. MO shall be performed once in 6 months. Should there be any failure

MO should be performed immediately after repair works.

1.3. During MO it is recommended to carry out the work by two qualified

mechanical and electrical engineers, acquainted with the manual.

1.4. MO includes the following scope of work: partial disassemble of the

turnstile, cleaning of load-bearing frame, checking of parts and units

fixation, lubrication of subject to wear parts of actuating device, checking

of belt tension, setting the dismantled parts and a general inspection of the

turnstile.

Maintenance operations 5

2. Conditions for performance of technical maintenance

ATTENTION! It is strongly forbidden to perform works with connected

power of the turnstile. A failure to observe safety requirements, indicated

in this Section, may cause damage to life and health of people, complete or

partial loss of operating capability of the product and (or) auxiliary

equipment.

ATTENTION! It is strongly forbidden to unfasten a cross-board, located

under the indication panel. Otherwise the manufacturer will terminate the

validity of warranty for the product.

ATTENTION! It is not recommended to adjust stroke limitation units for

solenoids, neither to adjust tension of springs. These units have been

adjusted at the factory. Disturbance of these adjustments may cause

malfunctions for the whole electromechanical system.

3. Partial disassembly of the turnstile

General View of the turnstile is shown on Fig.1

Switch off the power supply unit of the turnstile and disconnect it from the

mains.

Cube С-01 turnstile 6

To get an access to all required units of the turnstile it is necessary to

disassemble the turnstile partially. This scope of works includes removal

of the protective backshell. In order to get that done unscrew two screws

(1) and four screws (2), smoothly move the backshell up at a small

distance so that not to break the cable, coming to the indication board (Fig.

2). Disconnect the cable from the indication board.

Move the backshell up to the end and release an access to the swivel

mechanism. The view after removal of the backshell is shown on Fig 3.

Fig.1

Indication

panel

Rotary mechanism

equipped with

control unit

Protective

backshell

Rack

Base

Maintenance operations 7

Fig.2

Move

up

Cube С-01 turnstile 8

Fig.3

Fold arms for ease of further work, to achieve this retract fixation lock 2 of

the crossbars (Fig.3) and while holding one crossbar in a fixed position

rotate the other crossbar by the other hand clockwise so that all the

crossbars would align (Fig 4), put folded arms down (Fig 5) .

Maintenance operations 9

Fig.4

Cube С-01 turnstile 10

Fig.5