OYPLA DIY 3312 Bedienungsanleitung
Page 1
Model Code: 3312
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 3312
Contents
1Front Cover
-
2Safety
Instructions
-
2 Warnings
-
3 Assembly
Instructions
-
3Maintenance
-
4Operating
Instructions
-
4Back Cover
End
Laminate Floor
Cutter
Page 2
Model Code: 3312
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2 Warnings
-
3 Assembly
Instructions
-
3Maintenance
-
4Operating
Instructions
-
4Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
Always keep the cutting blade in the fully
closed position when not in use.
Keep fingers and hands away from the
blade cutting area.
Periodically check that all fixings and
fittings remain tight.
Do not discard any of the packaging until
you have checked that you have all of
the parts and fitting required.
Use the correct fixings as indicated. Do
not tighten any of the fixings fully until
the unit is completely assembled, then
finish by tightening all fixings. All fixings
must be tightened before use.
If the product is damaged or has any
defects, please contact
Only use this product on stable, level and
dry ground.
This product is not a toy, and is only to
be used for its intended purpose.
Do not make any alterations or
modifications to this product.
Clean only with a damp cloth. Do not use
strong industrial cleaning substances.
Leaving the product outside exposed to
weather, especially direct sun and rain,
will speed the weathering process. This
can be slowed by removing the product
from these conditions, or covering it with
a suitable cover.
Keep fingers, loose clothing, and hair
away when using the product.
This product is not intended for use by
persons (including children) with
reduced physical, sensory and mental
capacities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the product by persons responsible for
their safety.
⚠This product contains sharp parts.
Always take extra care when operating this
product.
⚠We recommend the use of appropriate
PPE whilst operating this product, such as
protective gloves.
⚠Never allow children to play with or
operate the product. Keep the product out of
the reach of children and pets.
Warnings
Page 3
Model Code: 3312
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
2 Warnings
-
3 Assembly
Instructions
-
3Maintenance
-
4Operating
Instructions
-
4Back Cover
End
Assembly Instructions
Maintenance
Keep the cutter clean, and store it in a dry place whilst it is not in use.
Keep the edges of the blade sharp by using a sharpening stone
periodically.
Periodically check that all fittings and parts remain tight.
Page 4
Model Code: 3312
Oypla.com LLP / www.oypla.com
=
Contents
1Front Cover
-
2Safety
Instructions
-
2 Warnings
-
3 Assembly
Instructions
-
3Maintenance
-
4Operating
Instructions
-
4Back Cover
End
Operating Instructions
Please refer to the instructions below for instructions on how to operate your product.
1. Place the cutter on the floor, ensuring the surface is level, dry and clean.
2. Mark the board to be cut to the size required, and insert it against the
back stop. The V-Support (L) should be used to support the laminate
whilst cutting.
3. Always cut the laminate board with the finished side up. Place the
grooved or indented side of the laminate against the backstop, with the
tongue side being closest to the blade. Begin the cut by holding the
laminate firmly with one hand and cutting into the laminate with the
blade approximately ½ in, before proceeding with both hands with a
smooth, powerful downward motion to complete your cut.
4. Remember, the cut side should always be placed along the wall to be
covered up by baseboard or finish moulding.
Andere OYPLA DIY Cutter Handbücher
Beliebte Cutter Handbücher anderer Marken
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung
Makita
Makita DCS552 Bedienungsanleitung
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Bedienungsanleitung
Makita
Makita 4112HS Bedienungsanleitung
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Bedienungsanleitung
Hitachi
Hitachi CM 4SB2 Fehlerbehebungshandbuch
