P5 FutureNow FNIP-6x2AD Bedienungsanleitung

1 | Page

FutureNow FNIP-6x2AD

Installation and Operation Manual

rev 28.04.2020

6 Channel Smart Dimmer with Local Inputs

/DIN Rail and Surface mountable/

The FNIP-6x2AD dimmer

 
2 | Page 
 
Contents 
MAIN FEATURES................................................................................................................................................. 3 
INSTALLATION.................................................................................................................................................... 4 
Terminal connections.......................................................................................................................................... 4 
Wiring................................................................................................................................................................. 6 
Outputs................................................................................................................................................................ 7 
Local inputs......................................................................................................................................................... 8 
Status LED indicators ..................................................................................................................................... 9 
Input status LEDs............................................................................................................................................ 9 
Run LED......................................................................................................................................................... 9 
Input power LED ............................................................................................................................................ 9 
Communication LEDs................................................................................................................................... 10 
Output status LEDs ....................................................................................................................................... 10 
CONFIGURATION.............................................................................................................................................. 11 
Configuration via the web interface.................................................................................................................. 11 
Connecting to the web server of the module................................................................................................. 11 
Network settings ............................................................................................................................................... 12 
Users and user rights......................................................................................................................................... 14 
Channel settings................................................................................................................................................ 15 
Dim settings ...................................................................................................................................................... 16 
Combining channels...................................................................................................................................... 17 
Scenes ............................................................................................................................................................... 18 
Firmware Upgrade ............................................................................................................................................ 19 
OPERATION........................................................................................................................................................ 20 
Operation via local inputs ................................................................................................................................. 20 
Input modes....................................................................................................................................................... 20 
Operation via the built-in web server................................................................................................................ 22 
Operation via TCP ............................................................................................................................................ 24 
TECHNICAL SPECIFICATIONS ................................................................................................................... 25 
REFERENCES.................................................................................................................................................. 26 
CONTACT DETAILS...................................................................................................................................... 26 
 

3 | Page

MAIN FEATURES

Fail-safe Operation

All-in-one dimmer

6 outputs for switching and dimming 6 lighting circuits

6 galvanically isolated multi-purpose inputs for direct control or connecting

digital sensors

Temperature monitoring

Overheat protection (both from software and hardware)

Overcurrent protection

Ultimate Flexibility

Switching on/off any loads (certain limitations apply)

Both trailing and leading-edge dimming

Automatic load type detection

Possibility to combine two outputs for more wattage

Standard DIN rail mount

Voltage, frequency, power consumption metering

100 dim levels (800 level hardware resolution)

Preset dim level –outputs will go to the specified level when turned on

Dim level memory (if preset dim level is set to zero)

Adjustable minimum and maximum dim levels

Adjustable ramp rates

Delayed off mode with adjustable duration

Lighting scenes

Enhanced Connectivity

Built-in web server for configuration, control and monitoring

Multiple users with different rights

TCP communication with simple ASCII commands

Automatic event reports of status changes of inputs and outputs

Firmware upgrade via LAN

Industry-Wide Interoperability

Full Integration with home controllers from most major vendors

Compatible with any momentary contact switches available on the market

4 | Page

INSTALLATION

WARNING! The module is connected to mains/line voltage! The

installation must be performed by a qualified electrician in

accordance with the local electrical codes!

Turn off power (main circuit breaker) before installation!

This equipment shall be installed in a closed cabinet with no access

to live parts. Only the top enclosure of the equipment (where the

label is affixed) is allowed to be accessed by the operator.

Terminal connections

Every FutureNow module has a wiring diagram on the front to help the installer

when connecting the modules at installation sites. See Figure 2.

The terminal connections of the FNIP-6x2AD are listed in Table 1.

5 | Page

Figure 2. FNIP-6x2AD front view with terminal connectors

Load

Control

No.

Description

No.

Description

Output 1 Live

27.

Inputs Common

230V Mains Input Live for ch1 and ch2

28.

Input 1

Neutral INPUT

29.

Inputs Common

Output 2 Live

30.

Input 2

12.

Output 3 Live

31.

Inputs Common

13.

230V Mains input Live for ch3 and ch4

32.

Input 3

14.

Neutral INPUT

33.

Inputs Common

15.

Output 4 Live

34.

Input 4

22.

Output 5 Live

35.

Inputs Common

23.

230V Main Input Live for ch5 and ch6

36.

Input 5

24.

Neutral INPUT

37.

Inputs Common

25.

Output 6 Live

38.

Input 6

Low voltage inputs for the module

No.

Description

39.

Power for the Inputs GND

40.

Power for the Inputs +10V.. +36V DC

6 | Page

41.

Power for the Main Circuit GND

42.

Power for the Main Circuit +10V.. +36V DC

Table 1: FNIP-6x2AD terminal connections

Wiring

A typical wiring diagram is shown in Figure 3.

Figure 3. Wiring diagram

All line inputs must be on the same phase and on the same circuit breaker!

Recommended wire types

Ethernet cable: Twisted pair, CAT5 or better.

Outputs: According to the loads attached to the outputs (current and voltage).

Inputs: A pair of low or high voltage cables. The inputs use low voltage signals.

Mains/line voltage wiring must be kept physically separated from Ethernet and signal

wiring.

Power requirements

The module requires 10V DC –36V DC through terminals 41 and 42.

N L N N

Light

1Light

N L N N

Light

3Light

N L N N

Light

5Light

Local inputs

+10V –36V DC for the inputs

+10V –36V DC for the main circuit

Ethernet

FNIP-6x2AD

7 | Page

If local inputs are to be used, 10V DC - 36V DC through terminals 39 - 40 is also

required.

Please make sure that the polarity is correct!

The galvanic isolation of the inputs is only effective when a separate power supply

is used for powering the inputs. The FNIP-6x2AD has separate power input

terminals (39 and 40) for this purpose. If you choose not to use the extra

protection the isolated inputs offer, you can use the same power to supply both

the main circuit and the inputs. In that case, simply connect terminal 39 to terminal

41 and terminal 40 to terminal 42.

Apply 230V 50 Hz AC live on terminals 3, 13 and 23 and neutral on terminal 4 and

14 and 24.

Please make sure that all the three line inputs (terminal 3, 13 and 23) are

on the same phase and on the same circuit breaker! Different phase

connection would create a short circuit and damage the module!

Live on terminal 3 powers output 1 and output 2, live on terminal 13 powers output

3 and output 4, live on terminal 23 powers output 5 and output 6.

The loads should be connected between the outputs of the module

(terminal 2, 5, 12, 15, 22, 25) and a neutral point somewhere outside the

module.

Connecting the Neutral legs of the loads to the module could damage the

module. This will void the warranty.

Ethernet connection

Connect the module to the LAN via the RJ45 Ethernet socket.

Outputs

The FNIP-6X2AD supports both trailing and leading edge dimming modes. It

handles most any lighting load be it resistive, inductive or capacitive, such as

incandescent, line voltage and low voltage halogens with both electronic and iron

core transformers, phase-cut dimmable fluorescents and compact fluorescents.

Phase-cut dimmable line voltage LEDs and LED Drivers must be controlled in

trailing edge dimming mode.

8 | Page

Do not attach any other type of load to the outputs if dimming of the

outputs is enabled! Using an improper load can damage both the attached

device and the FNIP-6x2AD, creating a potential fire hazard!

Only use lights with built-in ballasts/drivers that meet CE emission

standards. For example, spikes generated by certain LED drivers can

damage the dimmer.

Apart from dimming, the FNIP-6x2AD can also be used to switch (on/off only) non-

dimmable loads that don’t exceed the specifications.

As a precaution, dimming of the outputs is disabled by default. If you use dimmable

loads, you must enable dimming for each channel.

Local inputs

For each output there is a local input to allow for manual operation. If you do not

wish to use local inputs, this section may be skipped.

Connect dry contacts (pushbuttons, momentary switches, relay contacts, etc.) or

open collector transistor outputs across the appropriate input terminals and the

input common terminal. Voltage for the inputs is supplied by the module itself.

WARNING! Avoid supplying voltage on these terminals!

All input ports are galvanically isolated to protect the unit against unwanted effects

of ground loops, overvoltage or misconnections.

The galvanic isolation is only effective when an independent power supply is used

for powering the inputs. The FNIP-6x2AD has separate power input terminals for

this purpose. See section “Power Requirements” if you don’t want to use two

separate power supply units.

To assure an additional level of safe and reliable operation, the inputs are also

software protected against the effects of noise spikes that usually occur when

heavy inductive loads (motors, fans, etc.) are switched nearby.

Three-way switches can be implemented by simply connecting multiple

momentary switches in parallel.

9 | Page

Status LED indicators

In order to make installation and debugging easier, communication and channel

states are displayed via LEDs.

Use the board layout drawing in Figure 4. to locate the status LEDs.

Figure 4. The board layout of the FNIP-6x2AD

Input status LEDs

Each input has a dedicated status LED that illuminates solid green when the

corresponding input is activated.

Run LED

When on, it indicates that the Central Unit of the module works properly.

Input power LED

When illuminated, it indicates that the input power is present.

Er St

LEDs

Com

LEDs

Inputs 10V –36V Power Ethernet

Input Power

LED

Run LED

MCU

Output LEDs

1 2 3

Output 1

Output 2

Line in

Output LEDs

4 5 6

Reset

Input status

LEDs

Neutral

Output 3

Output 4

Line in

Neutral

Output 5

Output 6

Line in

Neutral

2 6 12 15 22 25

27 38 39 42

10 | Page

Communication LEDs

Con LED

The Con LED is on when the module is connected to the Ethernet network.

Act LED

Indicates communication via Ethernet

Status LEDs

St LED

It is illuminated while the boot loader is active and it is blinking during a firmware

upload procedure. This should only happen during hardware resets and in the

second phase of firmware updates.

AC LED

Indicates the presence of the 50/60Hz line voltage

Er LED

The Er LED turns on if the module gets overheated. This LED will not turn off

until the module is power cycled or the temperature of the heat sink drops below

40°C.

Output status LEDs

Each output has a dedicated status LED that illuminates solid red when the

corresponding output is activated. In case of overcurrent the corresponding LED

starts flashing. The error condition resets when the output is turned on again.

Inhaltsverzeichnis

Andere p5 Dimmer Handbücher

p5 FNIP-12xPWM Bedienungsanleitung

Beliebte Dimmer Handbücher anderer Marken

ZooZ

ZooZ ZEN54 LR Bedienungsanleitung

Lex

Lex 6KW Bedienungsanleitung

DIODE LED

DIODE LED TOUCHDIAL Mini Bedienungsanleitung

Viessmann

Viessmann 5590 Bedienungsanleitung

American DJ

American DJ DP-8A Bedienungsanleitung

Teleco

Teleco TVSTICK868RGB29 Bedienungsanleitung

INSTEON

INSTEON LampLinc 2457D2 Bedienungsanleitung

LEGRAND

LEGRAND WattStopper RH703PTU Bedienungsanleitung

ADB

ADB EURODIM TWIN TECH Bedienungsanleitung

Sinope

Sinope DM2550ZB-C4 Bedienungsanleitung

SkyLink

SkyLink SK7 Bedienungsanleitung

Makel

Makel RC Bedienungsanleitung

Lightronics

Lightronics XC-62 Bedienungsanleitung

Triton Blue

Triton Blue DM-1225 Bedienungsanleitung

ETC

ETC ES750 Betriebsanleitung

NA OMEGA + Bedienungsanleitung

GE ZB3001 Bedienungsanleitung

LSC

LSC DP-1210 Bedienungsanleitung

p5 FutureNow FNIP-6x2AD Bedienungsanleitung

Beliebte Dimmer Handbücher anderer Marken