Pacific 110ACX Bedienungsanleitung

ACX SERIES

AC POWER SOURCES

OPERATION

MANUAL

PAGE LEFT INTENTIONALLY BLANK FOR HARDCOPY VERSIONS OF THIS DOCUMENT

ACX-SERIES

OPERATION MANUAL

FOR THE

MODELS

110ACX

115ACX

118ACX

PPS PART NO. 150118-10

THIS MANUAL ASSIGNED TO S/N :

THE INFORMATION CONTAINED

IN THIS MANUAL IS PROPRIETARY TO

PACIFIC POWER SOURCE, INC.

AND MAY NOT BE COPIED OR REPRINTED

WITHOUT ITS EXPRESSED WRITTEN CONSENT.

PACIFIC POWER SOURCE, INC.

17692 Fitch Irvine, CA 92614

SIXTH EDITION

CERTIFICATION

PACIFIC POWER SOURCE CERTIFIES THAT THIS INSTRUMENT WAS

THOROUGHLY TESTED AND INSPECTED AND FOUND TO MEET OR

EXCEED ITS PUBLISHED SPECIFICATIONS WHEN IT WAS SHIPPED

FROM THE FACTORY.

LIMITED WARRANTY

Pacific Power Source (PPS) warrants each unit to be free from defects in

material and workmanship. For the period of two (2) years from the date of

shipment to the purchaser, PPS will either repair or replace, at its sole

discretion, any unit returned to its factory in Irvine, California or other factory

authorized service center. This warranty does not cover batteries. It does not

cover damage arising from misuse of the unit or attempted field modifications or

repairs. This warranty specifically excludes damage to other equipment

connected to this unit.

Upon notice from the purchaser within (30) days of shipment of units found to be

defective in material or workmanship, PPS will pay all shipping charges for the

repair or replacement. If notice is received more than thirty (30) days from

shipment, all shipping charges shall be paid by the purchaser. Units returned

on debit memos will not be accepted and will be returned without repair.

This warranty is exclusive of all other warranties, express or implied.

For a listing of local contacts or other information, please visit us online at:

www.pacificpower.com .

TABLE OF CONTENTS

PAGE

1GENERAL ................................................................................................................................................... 7

1.1 USING THIS MANUAL ..................................................................................................................... 7

1.2 SAFETY NOTICES .......................................................................................................................... 8

1.3 GENERAL PRODUCT DESCRIPTION .......................................................................................... 12

2SPECIFICATIONS .................................................................................................................................... 13

2.1 ELECTRICAL SPECIFICATIONS .................................................................................................. 13

2.1.1 INPUT POWER REQUIREMENTS.....................................................................................................13

2.1.2 OUTPUT POWER...............................................................................................................................14

2.1.3 OUTPUT POWER FACTOR...............................................................................................................16

2.1.4 OUTPUT FREQUENCY......................................................................................................................16

2.1.5 OUTPUT DISTORTION ......................................................................................................................16

2.1.6 OUTPUT LOAD REGULATION ..........................................................................................................16

2.1.7 INPUT LINE REGULATION................................................................................................................16

2.1.8 OUTPUT BANDWIDTH.......................................................................................................................16

2.1.9 LOAD TRANSIENT RESPONSE........................................................................................................16

2.1.10 OUTPUT DC OFFSET........................................................................................................................17

2.1.11 OUTPUT PROTECTION.....................................................................................................................17

2.1.12 OUTPUT CONTROL CHARACTERISTICS........................................................................................17

2.1.13 OUTPUT ISOLATION.........................................................................................................................17

2.2 MECHANICAL SPECIFICATIONS ................................................................................................. 17

2.2.1 DIMENSIONS AND WEIGHT..............................................................................................................17

2.2.1 DIMENSIONS DRAWINGS.................................................................................................................18

2.2.2 INPUT POWER CONNECTION..........................................................................................................19

2.2.3 OUTPUT POWER CONNECTION......................................................................................................19

2.2.4 CHASSIS SLIDE MOUNTS ................................................................................................................19

2.3 ENVIRONMENTAL SPECIFICATIONS ......................................................................................... 19

2.3.1 TEMPERATURE RANGE ...................................................................................................................19

2.3.2 COOLING ...........................................................................................................................................19

2.3.3 ALTITUDE...........................................................................................................................................19

2.3.4 POLLUTION DEGREE........................................................................................................................19

2.3.5 THERMAL PROTECTION ..................................................................................................................19

3INSTALLATION ........................................................................................................................................ 20

3.1 CHASSIS PLACEMENT................................................................................................................. 20

3.1 CHASSIS PLACEMENT (CONTINUED) ............................................................................................ 21

3.2 OUTPUT RANGE CONFIGURATION ............................................................................................ 21

3.3 INPUT POWER CONNECTION ..................................................................................................... 22

3.3 INPUT POWER CONNECTION (CONTINUED) ................................................................................ 23

3.4 OUTPUT POWER CONNECTION ................................................................................................. 24

3.4 OUTPUT POWER CONNECTION (CONTINUED) ............................................................................ 25

3.5 REMOTE INTERFACE ................................................................................................................... 25

3.6 AUX I/O INSTALLATION ................................................................................................................ 26

3.7 EXTERNAL SENSE CONNECTION .............................................................................................. 27

TABLE OF CONTENTS

PAGE

4OPERATION ............................................................................................................................................. 28

4.1 FRONT PANEL CONTROLS ......................................................................................................... 28

4.2 INITIAL POWER-UP ...................................................................................................................... 29

4.3 ROUTINE POWER-UP .................................................................................................................. 30

4.4 SYSTEM TURN-OFF ..................................................................................................................... 30

4.5 SYSTEM SHUTDOWN .................................................................................................................. 31

4.5.1 SHUTDOWN CONDITIONS......................................................................................................................31

4.5.2 RESETTING SHUTDOWN FAULTS .........................................................................................................31

4.6 OUTPUT VOLTAGE FORMS ......................................................................................................... 32

4.7 AUDIBLE ALERT ........................................................................................................................... 32

4.8 CONSTANT CURRENT MODE ..................................................................................................... 33

4.9 CONSTANT VOLTAGE MODE (CURRENT PROTECTION MODE) ............................................. 34

4.10 POWER PROTECTION MODE ..................................................................................................... 36

5MAINTENANCE ........................................................................................................................................ 37

5.1 MAINTENANCE INTERVAL........................................................................................................... 37

6CALIBRATION .......................................................................................................................................... 38

6.1 CALIBRATION INTERVAL ............................................................................................................. 38

6.2 TEST EQUIPMENT REQUIREMENTS .......................................................................................... 38

6.3 CALIBRATION PROCEDURE ....................................................................................................... 38

6.3 CALIBRATION PROCEDURE ( CONT. ) ......................................................................................... 39

6.3.1 CONTROLLER CALIBRATION...........................................................................................................40

6.3.2 POWER SOURCE LOAD TEST .........................................................................................................40

7 SERVICE ................................................................................................................................................... 41

7.1 SERVICE PROCEDURE................................................................................................................ 41

7.2 SYSTEM LEVEL FACTORY PART NUMBERS ............................................................................. 41

7.3 SUB-ASSEMBLY AND CHASSIS COMPONENT PART NUMBERS ............................................ 41

INDEX ................................................................................................................................................................. 42

9MODIFICATIONS AND CHANGE NOTICES .......................................................................................... 43

LIST OF ILLUSTRATIONS

FIGURE 1.3 ACX SERIES POWER SOURCE FRONT VIEW...……………….……..…….……………….6

FIGURE 2.1 INPUT CURRENT VS. OUTPUT POWER FOR MODEL 118ACX…………..……………....7

FIGURE 2.2 OUTPUT RATING CURVES BY MODEL…………………………………………………….....9

FIGURE 2.3 OUTLINE DRAWING ....…………………………….…………………...................................12

FIGURE 3.3 INPUT AND OUTPUT CONNECTIONS …………….…………………………………….……17

FIGURE 3.4 ACX-SERIES SYSTEM ARCHITECTURE ………………………………………….………….19

FIGURE 3.5 AUX I/O DB25S PIN OUT DIAGRAM.……………………………………………….………….20

FIGURE 3.6 EXTERNAL SENSE WIRING ……………………………………………………………………21

FIGURE 4.1 FRONT PANEL CONTROLS …………………………………………………………………….22

SECTION 1 GENERAL

SECTION 1

GENERAL

1 GENERAL

This manual provides information required to properly use one of the ACX Series AC Power

Source models. This is a general Operations Manual and it describes the operation of the basic

power source. Installation, operation, and calibration are the subjects covered.

At this time, there are three models available in the ACX Series:

Model

Maximum Output Power VA

110ACX

1000 VA

115ACX

1500 VA

118ACX

1800 VA

All ACX models are configured with a digital UPC (Universal Programmable Controller).

Detailed operating instruction and control and metering specifications are described in the UPC

Series Operation Manual which is supplied with the unit.

1.1 USING THIS MANUAL

This manual provides instructions for installation and use of the ACX Series Power Source

equipment. For this reason, it is very important that the user reads sections 1 GENERAL

information, 3 INSTALLATION, and 4 OPERATION, prior to using this equipment. A thorough

understanding of these sections is required to safely and properly operate this equipment.

Section 2 lists the specifications of the equipment. Knowledge of this information is required to

gain maximum use of this equipment for a given application. The user is encouraged to read

this section in order to gain a deeper understanding of the capabilities of the ACX Power

Source.

Sections 5 and 6 list MAINTENANCE and CALIBRATION requirements of this equipment.

Refer to these sections when either maintenance or calibration is required.

Section 7 describes SERVICE methodology and provides system, sub-assembly, and

component part numbers to aid the operator in making any factory authorized field repairs.

Section 8 contains the INDEX for this manual.

Section 9 contains product change notices, errata, and data relative to customer specified

modifications. Read Section 9 before operating the equipment. This is especially true when

modifications (MODs) have been installed, since these can change system operation.

If questions arise while reading this manual, the user is encouraged to call the Pacific Power

Source customer service department. Pacific maintains a toll-free number: 1-800-854-2433 or

use +1 (949) 251-1800.

SECTION 1 GENERAL

1.2 SAFETY NOTICES

The ACX is capable of transferring very large amounts of electrical energy very quickly. This

basic quality is fundamental to any high-performance power source. The warnings and cautions

listed below should be observed at all times.

WARNINGS are conditions which are hazardous to user personnel. All warnings throughout

this manual will be formatted as shown below. A condition which is hazardous to both personnel

and equipment will be issued as a warning.

CAUTION statements indicate a dangerous situation which may damage the equipment but is

not a threat to life or limb. Cautions will assume the format shown on page 3. All cautions

should be rigorously observed.

CONSIGNES de SECURITÉ

La ACX est en mesure de transférer des forts niveaux d’énergie électrique et cela de manière

très rapide. Cette caractéristique est une qualité fondamentale pour ce type d’équipement haute

performance. Les règles de sécurité, avertissements et précautions décris ci-dessous doivent

être observés à tout moment.

Attention! (Avertissements): conditions dangereuses pour le personnel utilisateur. Tout les

avertissements dans ce manuel seront formattés et indiqués comme ci-dessous. Toute

condition qui peut être dangereuse à la fois pour le personnel utilisateur et l’équipement sera

indiquée comme avertissement.

Précautions: elles indiquent une situation dangereuse pouvant endommager l’équipement,

mais qui n’est pas une menace pour la vie ou un danger pour un member. Les messages de

précautions seront formattés comme sur la page 3 tout au long ce manuel et doivent étre

observés rigoureusement.

SECTION 1 GENERAL

WARNING

ATTENTION

THIS EQUIPMENT CONTAINS HIGH ENERGY, LOW IMPEDANCE CIRCUITS!!

LETHAL POTENTIALS ARE CONTAINED WITHIN THE CABINET.

CARE MUST BE EXERCISED WHEN SERVICING THIS EQUIPMENT

TO PREVENT SERIOUS OPERATOR INJURY OR EQUIPMENT DAMAGE.

VOLTAGE AT THE TERMINALS RESPONDS INSTANTLY WHEN THE OUTPUT IS ACTIVATED.

OBSERVE THE FOLLOWING WHEN SERVICE, MAINTENANCE, OR CALIBRATION ARE REQUIRED:

1. REMOVE ALL JEWELRY FROM HANDS, ARMS AND NECK WHEN SERVICING THIS

EQUIPMENT. THIS PREVENTS THE POSSIBILITY OF SHORTING THROUGH THE JEWELRY

AND CAUSING BURNS OR ELECTROCUTION OF THE OPERATOR.

2. WEAR SAFETY GLASSES WHEN SERVICING THIS EQUIPMENT TO PREVENT EYE INJURY

DUE TO FLYING PARTICLES CAUSED BY ACCIDENTAL SHORT CIRCUIT CONDITIONS.

3. DO NOT REMOVE ANY PANEL OR COVER WITHOUT FIRST REMOVING THE INPUT SERVICE

BY OPENING ALL CIRCUIT BREAKERS.

4. SERVICE OTHER THAN EXTERNAL CLEANING SHOULD BE REFERRED TO PERSONNEL

AUTHORIZED BY THE FACTORY TO SERVICE THIS EQUIPMENT.

CET EQUIPEMENT CONTIENT DES CIRCUITS ELECTRIQUES DE FORTE ENERGIE ET A FAIBLE

IMPEDANCE!! DES POTENTIELS A CARACTERE MORTEL SONT CONTENUS A L’INTERIEUR DE

L’EQUIPEMENT.

UNE ATTENTION PARTICULIERE EST IMPERATIVE DANS LE CADRE DU SERVICE DE CET

EQUIPEMENT AFIN DE PREVENIR TOUT RISQUE POUVANT ENTRAINER UN ACCIDENT DE

L’OPERATEUR OU UN DOMMAGE DE L’EQUIPEMENT.

LA TENSION AUX BORNES DE SORTIE DE L’EQUIPEMENT EST PRESENTE INSTANTANEMENT

LORSQUE LA SORTIE EST ACTIVEE.

LES REGLES DE SECURITE SUIVANTES DOIVENT ETRE SUIVIES DANS LE CADRE DU SERVICE,

DE LA MAINTENANCE OU DE LA CALIBRATION DE L’EQUIPEMENT:

1. OTER TOUS LES BIJOUX DES MAINS, BRAS ET COU PENDANT LE SERVICE DE L’EQUIPEMENT

AFIN DE PREVENIR TOUT RISQUE DE COURT-

CIRCUIT PAR L’INTERMEDIAIRE DES BIJOUX QUI

POURRAIT CONDUIRE A DES BRULURES OU ELECTROCUTION DE L’OPERATEUR

2. PORTER DES LUNETTES A VERRE DE SECURITE PENDANT LE SERVICE DE L’EQUIPEMENT

AFIN DE PREVENIR TOUT RISQUE D’ACCIDENT OCULAIRE POUVANT PROVENIR DE

PARTICULES VOLANTES CREEES DANS DES CONDITIONS DE COURT-CIRCUIT

ACCIDENTELLES.

3. NE JAMAIS OTER OU RETIRER DES PANNEAUX OU COUVERCLES DE PROTECTION SANS

AVOIR AU PREALABLE COUPER LE CIRCUIT D’ALIMENTATION DE L’EQUIPEMENT.

4. TOUT AUTRE SERVICE QUE LE NETTOYAGE EXTERNE DE L’EQUIPEMENT NECESSITE

L’INTERVENTION DE PERSONNEL QUALIFIE ET AUTORISE PAR L’USINE POUR CETTE

MAINTENANCE

SECTION 1 GENERAL

1.2 SAFETY NOTICES (continued)

CAUTION

PRECAUTION

READ SECTIONS 1, 3, AND 4 OF THIS MANUAL

BEFORE INSTALLING OR OPERATING THIS EQUIPMENT.

LIRE LES CHAPITRES 1,3 ET 4 DE CE MANUEL

AVANT L’INSTALLATION ET L’UTILISATION DE CET EQUIPEMENT

WARNING

ATTENTION

IF THIS EQUIPMENT IS NOT USED IN A MANNER SPECIFIED BY THE MANUFACTURER,

THE PROTECTION PROVIDED BY THE EQUIPMENT MAY BE IMPAIRED

SI CET EQUIPEMENT N’EST PAS UTILISE D’UNE MANIERE SPECIFIEE PAR LE FABRICANT,

LA PROTECTION FOURNIE PAR L’EQUIPEMENT PEUT ETRE ALTEREE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pacific Wechselstromverteilung Handbücher

Pacific

Pacific AMX series Bedienungsanleitung

Beliebte Wechselstromverteilung Handbücher anderer Marken

PS Audio

PS Audio PowerPlay 8500 Bedienungsanleitung

Elgar

Elgar CW 2501P Bedienungsanleitung

Panamax

Panamax M5300-PM Bedienungsanleitung

Ring Powering

Ring Powering RINV500 PowerSource Bedienungsanleitung

ABB

ABB System pro E power Handbuch

Heath

Heath Heathkit HL-2200 Bedienungsanleitung

Panamax

Panamax Powermax PM8-EX Bedienungsanleitung

Furman

Furman AC-210 E Bedienungsanleitung

Abtus

Abtus PWR-DA09C/P Bedienungsanleitung

Belkin

Belkin PureAV PF30L Bedienungsanleitung

Furman

Furman P-1800 PF Prestige Series Bedienungsanleitung

EasyFocus

EasyFocus SGR-UPS5011 Bedienungsanleitung

Panamax

Panamax VT1512-IP Bedienungsanleitung

socomec

socomec ATyS p Bedienungsanleitung

Panamax

Panamax M8DBS-EX Bedienungsanleitung

Panamax

Panamax M5400-EX Bedienungsanleitung

Chroma

Chroma 61501 Bedienungsanleitung

Furman

Furman P-1800 AR Prestige Serie Bedienungsanleitung