Pakedge WK-1-C Bedienungsanleitung

QUICK START GUIDE

WK-1-C Access Point

802.11ac Dual Band Access Point

Version 1.2

Contents

Package contents 3

WK-1-C mounting 4

Powering up the access point 11

Conguring the hardware 13

Step 1: Logging in 13

Step 2: Radio 19

Step 3: Creating security proles 23

Step 4: Conguration 25

Technical Support 28

Package contents

Please refer to the installation manual of your product.

WK-1-C

• 802.11ac Dual Band Access Point

• Built-in 2×2 internal antennas

• Powered by PoE+

• 2 LAN ports for network extensions

System requirements

• Windows or Mac PC with an Ethernet interface

WK-1-C default settings

• Operation Mode: Access Point

• IP Address: IP will be automatically assigned by router if a DHCP server is detected or, if no

DHCP server is detected, the default IP address will be automatically set to 192.168.1.250.

• Username/Password: pakedge/pakedgea

• SSID: Pakedge2.4-1 and Pakedge5-1

• Power Output: High

• Security: Disabled

1 Open the release latch and push on the back of WK-1-C to swing the WAP out from the

ceiling or wall bracket.

WK-1-C mounting

2 Swing the WAP down.

3 Using the supplied template, cut a 9.125”

diameter circle at the desired mounting location

for your WK-1-C. Route an in-wall Ethernet cable

through the opening on the back of WK-1-C

housing, then insert the WK-1-C into the ceiling

or wall.

4 Use a Phillips screwdriver to tighten the mounting ears. Use a clockwise

rotation.

NOTE: Do not use excessive force when tightening the mounting-ears. This can strip the mounting

ears and render them non-functional.

5 Plug the Ethernet cable into WK-1-C. Route the Ethernet cable as shown. Use the optional

cable clip, if necessary.

6 Swing the WAP back into the WK-1-C housing.

WK-1-C installation with optional pre-construction bracket

Pre-construction bracket sold separately.

1 Place the pre-construction bracket against the bottom of the ceiling studs at the desired

mounting location.

2 Mark locations for mounting screws. Drill 1/16” pilot holes at marked locations. Secure the

pre-construction bracket to ceiling studs using the provided hardware.

3 Install sheet rock over pre-construction bracket. Make note of where the cutout on the pre-

construction bracket is when installing the drywall.

4 Cut an opening in sheet rock using the cutout on the pre-construction bracket as a guide.

Note: The Pakedge logo should be facing outwards.

Inhaltsverzeichnis

Beliebte Zugangspunkt Handbücher anderer Marken

LevelOne

LevelOne WAP-6101 Bedienungsanleitung

Ruckus Wireless

Ruckus Wireless ZoneFlex R300 Bedienungsanleitung

Meru Networks

Meru Networks ap400 Bedienungsanleitung

Tranzeo Wireless Technologies

Tranzeo Wireless Technologies EL-500 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-IW Bedienungsanleitung

LevelOne

LevelOne WAP-8101 Bedienungsanleitung

EnGenius

EnGenius EWS550AP Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Bedienungsanleitung

Edge-Core

Edge-Core ECW5320 Bedienungsanleitung

Ruijie

Ruijie RG-AP130(W2) Installations- und Betriebsanleitung

Intellinet

Intellinet 524711 Bedienungsanleitung

Zoomnet

Zoomnet Bgate-GT10-D24-N22-P Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WAP-PC1200C Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket AC R5AC-PTMP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW Bedienungsanleitung

Ruijie Networks

Ruijie Networks RG-AP520-I(G2) Series Installations- und Betriebsanleitung

Hamlet

Hamlet Wireless Access Point 150 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-M Bedienungsanleitung