Pakedge SE-18 Bedienungsanleitung

SE-18, SE-26

16/24-Port Unmanaged

Gigabit Ethernet Switch

QUICK START GUIDE

Introduction

These SE Series unmanaged switches oer high-performance, plug-and-play,

gigabit Ethernet switching with 16/24 gigabit Ethernet ports and two gigabit SFP

ports, providing you a cost-eective, space-saving solution for expanding your

network. The fully gigabit Ethernet ports support high bandwidth for today’s most

demanding applications. The two SFP ports provide the ability to add ﬁber-optic

connectivity between other network switches, giving you the option for long-distance

communications.

Automatic MDI/MDI-X crossover detection ensures you will not need to worry about

the cable type by automatically switching the port’s receive and transmit connections

with plugged in devices. Also, ﬂow control ensures the accuracy of transmitted data.

What’s more, the 802.3x and back-pressure ﬂow control mechanisms work respectively

for full- and half-duplex modes.

Access Point’s

• Complies with 10 BASE-T speciﬁcations of the IEEE802.3 standard, 100BASE-TX

speciﬁcations of the IEEE802.3u standard, and 1000BASE-T speciﬁcations of the

IEEE802.3ab standard

• Provides 16/24 10/100/1000 Mbps Ethernet ports, and two 100/1000 Mbps SFP

ports for optional ﬁber connection

• Supports back-pressure (half-duplex) and ﬂow control (IEEE 802.3x)

• Supports NWay protocol for speed (10/100/1000 Mbps) and duplex mode (half/

full) auto-detection

• Supports MDI/MDI-X auto crossover and polarity correction

• Supports 8K MAC address

• Supports 4.1 Mbit buer memory

• Supports 9K bytes jumbo frame

• Supports IEEE 802.3az Energy Ecient Ethernet

• Provides extensive LED indicators for network diagnostics

• Supports automatic loop detection and isolation

Package contents

• (1) 16/24-port gigabit switch with 2 SFP ports

• (1) AC power cord

• (1) Rack-mount brackets and screws

• (1) This Quick Start Guide

Overview

Front panel

LED Status Operation

Power Steady blue Swith is powered on

O Switch is powered o

Loop Blinking red A loop exists

O No loop exists

Link/ACT

Steady blue Valid port connection

Blinking blue Valid port connection, data transmitting/receiving

O Port is disconnected

Rear panel

Auto-negotiation allows ports to run at one of the following operation modes:

Port Media Speed (Mbps) Duplex mode

10/100/1000

Mbps

10/100/1000 Mbps (copper) 10 Full

Half

100 Full

Half

1000 Full

10/100/1000 Mbps (ﬁber)

(SFP required)

100 Half

1000 Full

Power receptacle

To be compatible with worldwide electric service standards, the switch is designed to

use the power supply in the range from 100 to 240VAC, 50/60 Hz. Make sure that your

outlet standard is within this range.

To power on the switch:

1 Connect the power cord securely into the power receptacle on the back of the

switch and to an electrical outlet.

2 Verify that the power LED on the front of the switch is on and indicating normal

power status.

Installation

This switch can be placed directly on your desktop or mounted in a rack. All features of

the switch are available while the switch is powered on.

Desktop installation

1 Attach the provided rubber feet to the bottom of the switch to keep the switch

from slipping. The recommended position has been marked with a small square.

2 Place the switch on a level surface that can support the weight of the unit and the

relevant components.

3 Connect the power cord to the switch and an electrical outlet.

Rack-mount installation

The switch can be mounted in a standard 19" rack. Rack mounting produces an orderly

installation when you have several related network devices. The switch is supplied with

two optional mounting brackets and screws.

To rack mount the switch:

1 Disconnect all cables from the switch.

2 Place the switch on a hard, ﬂat surface with the front facing you.

3 On each side of the switch, position a mounting bracket over the bracket

mounting holes, then insert and fully tighten the screws with a screwdriver.

4 Using the mounting brackets, mount the switch into the equipment rack with the

appropriate screws.

5 Reconnect all cables.

Network cable guidelines

• Crossover or straight-through cable: All ports on the switch support Auto-MDI/

MDI-X. Straight-through and crossover cables can be used to connect the switch

with PCs, as well as other devices such as switches, hubs, or routers.

• Category 5, 5e, 6a, or 7 UTP/STP cable: To make a valid connection and obtain

optimal performance, appropriate cables corresponding to dierent transmitting/

receiving speeds are required. To select a suitable cable, refer to the table below:

Media Speed

(Mbps)

Wiring

10/100/1000

Mbps (copper)

10 Category 5 UTP/STP

100 Category 5 UTP/STP

1000 Category 5, 5e, 6a, or 7 UTP/STP

1000 Mbps

(ﬁber)

(SFP required)

1000 The cable type diers depending on the SFP you

purchase. Refer to the SFP instructions.

Tips: To ensure optimal performance, we strongly recommend the below installation

environment:

• The switch has sucient ventilation. A minimum 1 inch (about 25 mm) space

around the unit is recommended.

• The switch and the relevant components are kept away from sources of electrical

noise, such as radios, transmitters, and broadband ampliﬁers.

• The switch is kept away from moist environments.

1010

Speciﬁcations

Standard

IEEE802.3 (10BASE-T)

IEEE802.3u (100BASE-TX)

IEEE802.3ab (1000BASE-T)

IEEE802.3x full-duplex ﬂow control

IEEE802.1p class of service, priority protocols

IEEE802.3az (Energy Ecient Ethernet)

Interface 16/24 10/100/1000 Mbps RJ-45 ports

2 SFP ports

Cable connections

RJ-45 (10BASE-T): Category 3, 4, 5 UTP/STP

RJ-45 (100BASE-TX): Category 5 UTP/STP

RJ-45 (1000BASE-T): Category 5, 5e, 6, or enhanced

UTP/STP

Fiber: depends on SFP types

Network data rate 10/100/1000 Mbps auto-negotiation

Transmission mode 10/100 Mbps: Full duplex, half duplex

1000 Mbps: Full duplex

LED indications

(1) Power LED (blue)

(1) Loop LED (blinking red)

(18/26) Port link/act LEDs (blue)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pakedge Schalten Handbücher

Pakedge

Pakedge S3 Series Bedienungsanleitung

Pakedge

Pakedge MS Series Bedienungsanleitung

Pakedge

Pakedge SK-24 Bedienungsanleitung

Pakedge

Pakedge SX-24P Bedienungsanleitung

Pakedge

Pakedge MS-1212 Bedienungsanleitung

Pakedge

Pakedge S3L-24P Handbuch

Pakedge

Pakedge SW24-GBM Bedienungsanleitung

Pakedge

Pakedge SW8-GBP Bedienungsanleitung

Pakedge

Pakedge SX-24P16 Bedienungsanleitung

Pakedge

Pakedge SE-8 Bedienungsanleitung

Pakedge

Pakedge SX-8P Bedienungsanleitung

Pakedge

Pakedge SX-8P Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch