Palfinger RC 400 P2 Bedienungsanleitung

Remote Control

Content

1General

1-1 Validity of operating instructions

1-2 Operating company

1-3 Operator

1-4 Safety equipment

1-5 Remote control components

1-6 Disposal

2Overview

2-1 Overview of the RC transmitter

3Remote control operation

3-1 Preparing remote control operation

3-2 Remote control operation

3-3 Warning horn / Emergency off button

3-4 Feedback to the transmission console

3-5 Stabilizer operation linear lever

3-6 Cable winch working position and transport position

3-7 Remote operation safety switch-off

3-8 Changing the radio channel (in case of radio interference)

3-9 Cable operation

3-10 Stop working with the remote control

3-11 Battery of the remote control system

3-12 Attaching and uncoupling of load by the crane operator

4Maintenance and servicing

4-1 Maintenance and servicing

4-2 Storeage

General

1-1

General

1-1

1General

1-1 Validity of operating instructions

The present operating instructions are only valid in combination with the operating instructions for the

crane.

Compliance with national regulations and laws to operate the remote control is obligatory.

1-2 Operating company

The operating company has to make sure that:

•he operator is familiar with this operating instruction, with the operating instruction of the device to

be controlled and with the operating instructions of any accessories used and that he has under-

stood them.

•the operator has been trained on the device to be controlled and on any accessory used and that

he has understood it.

•this and all other operating instructions are permanently available to the operator.

•the system may not be taken into operation by unauthorized persons.

1-3 Operator

Requirements to the operating staff see crane operating instructions.

1-4 Safety equipment

Safety equipment serves to protect the operator and must not be manipulated or taken out of opera-

tion. Warranty and guarantee will immediately expire when we find that the remote control (transmit-

ter, receiver) has been manipulated.

1-5 Remote control components

The remote control system must be operated with original Palfinger components only.

1-6 Disposal

Electronic components are special waste. This applies in particular to the batteries. It is not allowed to

dispose defective batteries into the environment.

Dispose all parts of the remote control system in compliance with national laws and regulations.

Overview

2-1

2Overview

2-1 Overview of the RC transmitter

The following section shows and describes a remote control transmitter (maximal variation) with all its

levers, switches, buttons, and display possibilities..

The picture is an example and shows the standard functions. The functions’ allocation to the

switches, levers or displays may be customized by an authorized Palfinger service center. Before tak-

ing the remote control into operation the first time every operator has to be trained and informed

about the way the functions, switches and displays are arranged on the RC transmitter used.

Small transmitter

60 70 9080

100

Large transmitter

60 70 9080

100

Overview

2-1

1 Battery status display On = LED continously red, remote control is ready for operating.

On = LED flashing red, low battery power. The system will be

switched off within the next minutes.

2 Toggle switch Automatic AOS, left = off / right = on

3 Key RC system start

4 Key Manual AOS on

5 Toggle key Option free left / right

Toggle switch (lift

before switch*) Only linear remote control (e.g. rotator, cable winch, outrigger

operation)

7 Key Crane operation / support operation switch

8 Display Rope winch overload protection (cut-off)

9 Push button OLP button / keep for 0.5 seconds pressed = horn

10 Push button HPLS On / Off

11 Push button Paltronic 50 On / Off

12 Display Load moment limitation of 2nd knuckle system

13 Display Workload display crane / fly jib 60% to 100%

14 Display Load moment limitation on crane

15 Display Load limitation system, reduced load limit

16 Display Automatic AOS, See chapter 3-4

17 Display Return oil recycling, See chapter 3-4

18 Display outrigger, See chapter 3-4

19 Plug Data cable (cable control)

Crane operation:

Slew crane left/right

Raise/lower main boom

Fold in/out knuckle boom

Extendable arms in/out

Rotator left/right

20 Linear lever max. 6x

Small transmitter

Open/close grab

*lift the key before switch

Overview

2-1

Linear lever max. 8x

Large transmitter

Left

Left – Increase motor speed permanently to

programmed value.

Center

Center – Motor idling

21 Toggle switch

Right Right – Increase motor speed when a crane

function is triggered.

22 Push button Links = Motor start / Rechts = Motor - stopp

23 Key Working lights on / off

24 Key return oil recycling off / on

Change crane speed

After switching transmitter on:

Crane speed last selected.

Button to the left = Slow the speed down one level.

Button to the right = Slow the speed down one level.

It is always possible to increase the speed.

25 Push button

There are 4 levels of

acceleration:

Factory settings:

50% LED blinks 3x

65% LED blinks 2x

85% LED blinks

100% LED is off.

Adjustable via Paldiag

26 Toggle switch Option free left / right

27 Radio quality display LED flashing green = poor or no radio communication

LED lights green = stable radio communication

28 Key Emergency push off button

Remote control transmitter without display:

26 Key OLP button / keep for 0.5 seconds pressed = horn

Overview

2-1

Control lever variants (small transmitter):

Linear control Linear control

Control lever variants (large transmitter):

up to 8 linear levers + one switching function

Joystick control, joystick control with turning function (like small transmitter)

(e.g. rotator / cable winch)

Remote control operation

3-1

3Remote contr ol operati on

3-1 Preparing remote control operation

Visual check of remote control transmitter:

Check the transmitter for damages every time before work.

Check:

•Operating lever for self-return.

•Inoperable switches

•Damaged parts

•Missing or damaged rubber sleeves.

•Charged battery, spare battery in re-charger.

All damages must be removed before using the remote control.

Battery:

The operating time with charged battery is approx. 8 hours.

Always treat the batteries with care.

Put completely charged battery into the transmission panel of the remote control system.

It is obligatory to keep a charged standby battery in the vehicle.

The control cable must be kept in the vehicle.

Andere Handbücher für RC 400 P2

Inhaltsverzeichnis

Andere Palfinger Fernbedienung Handbücher

Palfinger

Palfinger RC 400 P2 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung