Panasonic DMP-BD60 - Blu-Ray Disc Player Bedienungsanleitung

Andere Handbücher für DMP-BD60 - Blu-Ray Disc Player

1

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Panasonic Blu-ray-Player Handbücher

Panasonic

Panasonic DMP-BD75 Technische Daten

Panasonic

Panasonic DMP-BDT330 Bedienungsanleitung

Panasonic

Panasonic DMP-BD30 Bedienungsanleitung

Panasonic

Panasonic DMP-BDT350 Operating Manual (English Bedienungsanleitung

Panasonic

Panasonic DMP-BD75P Bedienungsanleitung

Panasonic

Panasonic DMP-BD70V - Blu-ray Disc/VHS Multimedia... Bedienungsanleitung

Panasonic

Panasonic DMP-BD30GN Bedienungsanleitung

Panasonic

Panasonic DMP-BDT110EG Bedienungsanleitung

Panasonic

Panasonic DP-UB420 Bedienungsanleitung

Panasonic

Panasonic DMPB500 - PORTABLE BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DMP-BD60K Bedienungsanleitung

Panasonic

Panasonic DMR-BW500EF Bedienungsanleitung

Panasonic

Panasonic DMP-BDT500 Bedienungsanleitung

Panasonic

Panasonic DMPB100 - PORTABLE BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DMP-BD87PX Bedienungsanleitung

Panasonic

Panasonic DMPB100 - PORTABLE BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DMP-B15K Bedienungsanleitung

Panasonic

Panasonic DMP-B15 - Portable Blu-ray Player Bedienungsanleitung

Panasonic

Panasonic DMP-BDT120 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-PWT420 Bedienungsanleitung

Panasonic

Panasonic DMP-BDT120 Bedienungsanleitung

Panasonic

Panasonic DMP-BDT110GA Bedienungsanleitung

Panasonic

Panasonic DMP-BDT215 Bedienungsanleitung

Panasonic

Panasonic DMP-BDT300GA Bedienungsanleitung

Beliebte Blu-ray-Player Handbücher anderer Marken

Samsung

Samsung BD-F5900 Bedienungsanleitung

Philips

Philips BDP3380K Bedienungsanleitung

Samsung

Samsung BD-P4600 Bedienungsanleitung

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Bedienungsanleitung

Pioneer

Pioneer BDP-140 Installations- und Betriebshandbuch

LG

LG HLX50W Bedienungsanleitung

Sony

Sony BDP-S300 - Blu-Ray Disc Player Bedienungsanleitung

Marantz

Marantz UD9004 Bedienungsanleitung

LG

LG BD611 Bedienungsanleitung

LG

LG BD611 Bedienungsanleitung

Marantz

Marantz BD7004 Kurzanleitung

Kogan

Kogan KABRP3DWFIA Bedienungsanleitung

Toshiba

Toshiba BDX2700 Bedienungsanleitung

Samsung

Samsung BD-E5400 Bedienungsanleitung

Samsung

Samsung BD-F5100 Bedienungsanleitung

Philips

Philips BDP7100 Bedienungsanleitung

LG

LG UBK80.DUSALLK Bedienungsanleitung

Sony

Sony BDP-S185 Bedienungsanleitung

Panasonic DMP-BD60/BD80

Region switching guide

With the mod. chip fitted the player will automatically play DVD's from all regions (1-6),

but for Blu-ray disc playback the region must be manually selected.

Blu-ray Region switching is done using the player's original remote control while the

player is in standby mode, by pressing the following buttons:

'1' : Select Blu-ray region 'A'

'2' : Select Blu-ray region 'B'

'3' : Select Blu-ray region 'C'

When the player is powered up out of standby mode the new Blu-ray region will be

active. The selected Blu-ray region will remain active until the player is disconnected

from mains power or a new region is selected while the player is in standby mode.

Note that the player must fully enter standby mode to allow the mod. chip to change the

Blu-ray region, therefore the player's "Quick Start" mode (which keeps the player fully

powered up even in standby mode) must be disabled when changing Blu-ray regions.

Blu-ray region switching is possible with any remote channel setting, 1, 2 or 3.

Panasonic DMP-BD60/BD80

Mod. chip fitting guide

Warning: Modifying your player will invalidate any existing warranty. The mod. chip is

difficult to fit, requiring soldering of small surface mount components and therefore

fitting should only be carried out by those with the appropriate experience. A low power

(15-25W) soldering iron with very small tip is essential. If you don't have the required

tools and experience do not attempt to fit the mod. chip as it's very likely that you will

damage your player.

Please read this guide fully before starting to fit the mod. chip.

Before opening the player ensure that all cables are completely disconnected from it.

Double check that the mains cable is disconnected.

To open the player remove the 7 fixing screws, 2 from left side, 2 from right side and 3

from the rear. The top cover can now be lifted off.

The main board is on the right side and the image below shows the areas where the mod.

chip will be connected to it.

6 pins on the mod. chip are used in total, #1, #2, #3, #4 and #8 connect to the main board

and #5 to the rear of the front panel.

Mod. chip pin #1 should be connected to the 2nd bottom of the 6 long solder pads, as

shown.

Mod. chip pins #2, #3, #4 and #8 should be connected to the small 8 pin chip as shown.

For access to the connection point for mod. chip pin #5 the front panel of the player has to

be removed. To remove the front panel, look for the 7 plastic clips holding it in place, 1

left, 1 right, 2 top and 3 bottom. Carefully unclip them from one side, then the other and

the front panel should pull free.

With the front panel removed you can now see the area where mod. chip pin #5 will be

connected.

Connect pin #5 to the point on the front panel PCB shown below.

Bring the wire for mod. chip pin #5 in under the metal plate at the front of the player,

ensuring that it doesn't block the connector shown at the left side.

When re-fitting the front panel check that all 7 plastic clips are fully in place, otherwise

the electrical connectors may not contact correctly.

Pins #1 and #5 should be connected with wires, however for the pins that connect to the 8

pin chip on the main board (#2, #3, #4 and #8) it's possible to either connect them with

wires or to "piggy-back" the mod. chip on top of the 8 pin chip on the board. If you

connect all the pins with wires then the mod. chip must be wrapped in insulation tape and

secured in a safe position, so the "piggy-back" option is quicker and only requires 2 wires

for pins #1 and #5.

To "piggy-back" the mod. chip, bend pins #2, #3, #4 and #8 inwards against the body of

the mod. chip and then #3, #4 and #8 as shown below. Trim pins #1 and #5 and

trim/remove the unused pins #6 and #7.

Bend the pins into position and then hold it against the chip on the board to make sure

they are lined up correctly. Once all the pins are lined up solder pin #8 first, then you can

carefully position the mod. chip by rotating it slightly and solder pins #2, #3 and #4.

It should then look similar to the image below.

And the full install should look like this, with the wires for pins #1 and #5 in place.

If you're not confident with the "piggy-back" fitting method just use wires to connect all 6

pins of the mod. chip.