Panasonic DMP-BD87P Bedienungsanleitung

ing and distribution is a violation of law.

ORDER NO. DSD1201001CE

B24

Blu-ray Disc Player

Model No. DMP-BD87P

DMP-BD87PC

DMP-BD77P

DMP-BD77PC

Colour

(K)...........Black Type

TABLE OF CONTENTS PAGE PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3

1.2. Leakage Current Cold Check ---------------------------3

1.3. Leakage Current Hot Check (See Figure 1.)--------3

2Warning--------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------4

2.2. Precaution of Laser Diode -------------------------------5

2.3. Static Electricity Protection Measures ----------------6

2.4. Ground for electrostatic breakdown

prevention----------------------------------------------------6

3 Service Navigation------------------------------------------------7

3.1. Service Information----------------------------------------7

3.2. How to Update Firmware---------------------------------7

4 Specifications ------------------------------------------------------9

4.1. Others (Licenses) ----------------------------------------10

5 Location of Controls and Components------------------13

6 Operating Instructions ----------------------------------------14

6.1. Taking out the Disc from Drive Unit when the

Disc cannot be ejected by OPEN/CLOSE

button--------------------------------------------------------14

7 Multiple Pressing Function----------------------------------15

7.1. About the Multiple Pressing of the Unit’s

Remote Control-------------------------------------------15

7.2. How to enter the Special Modes using the

Multiple Pressing Function of the Unit’s

Remote Control-------------------------------------------15

8 Service Mode-----------------------------------------------------18

8.1. About the Service Mode--------------------------------18

8.2. Service Mode List----------------------------------------19

9 Troubleshooting Guide----------------------------------------22

9.1. About Operation of Set ---------------------------------22

9.2. About Circuit-----------------------------------------------23

10 Wiring Connection and Voltage Data---------------------27

11 Disassembly and Assembly Instructions---------------28

11.1. Unit-----------------------------------------------------------28

11.2. When Replacing the Mechanism Unit and/or

Digital P.C.B. ----------------------------------------------32

12 Exploded View and Replacement Parts List-----------33

12.1. Casing Parts & Mechanism Section-----------------33

12.2. Packing & Accessories Section ----------------------34

12.3. Replacement Parts List---------------------------------35

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment

which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essen-

tial that these critical parts should be replaced with manu-

facturer’s specified parts to prevent X-RADIATION,

shock, fire, or other hazards. Do not modify the original

design without permission of manufacturer.

2. An Isolation Transformer should always be used during

the servicing of AC Adaptor whose chassis is not isolated

from the AC power line. Use a transformer of adequate

power rating as this protects the technician from acci-

dents resulting in personal injury from electrical shocks. It

will also protect AC Adaptor from being damaged by acci-

dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been over-

heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices

such as insulation barriers, insulation papers shields are

properly installed.

5. After servicing, make the following leakage current

checks to prevent the customer from being exposed to

shock hazards.

1.2. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-

lic cabinet part on the equipment such as screwheads,

connectors, control shafts, etc. When the exposed metal-

lic part has a return path to the chassis, the reading

should be between 1 MΩand 5.2 MΩ. When the exposed

metal does not have a return path to the chassis, the

reading must be infinity.

1.3. Leakage Current Hot Check

(See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF

capacitor, between each exposed metallic part on the set

and a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 V RMS.

A leakage current tester (Simpson Model 229 or equiva-

lent) may be used to make the hot checks, leakage cur-

rent must not exceed 1/2 mA. In case a measurement is

outside of the limits specified, there is a possibility of a

shock hazard, and the equipment should be repaired and

rechecked before it is returned to the customer.

Figure. 1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge

(ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-

ficient to damage an ES device).

2.2. Precaution of Laser Diode

2.3. Static Electricity Protection Measures

• The laser diode in the traverse unit (optical pick-up) may break down due to potential difference caused by static electricity of

clothes or human body.

So, be careful of electrostatic breakdown during repair of the traverse unit (optical pick-up).

2.4. Ground for electrostatic breakdown prevention

• As for parts that use optical pick-up (laser diode), the optical pick-up is destroyed by the static electricity of the working environ-

ment.

Repair in the working environment that is grounded.

2.4.1. Work table grounding

• Put a conductive material (sheet) or steel sheet on the area where the traverse unit (optical pick-up) is placed, and ground the

sheet.

2.4.2. Human body grounding

• Use the anti-static wrist strap to discharge the static electricity from your body.

2.4.3. When exchange the Drive

• Before remove the ESD prevention bag, make sure to use the anti-static wrist strap to discharge the static electricity when

replace the Drive.

Note:

The ESD prevention bag is used to replace the original short-circuit point.

It can be removed while placing the Drive.

3 Service Navigation

3.1. Service Information

This service manual contains technical information, which allow service personnel's to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

Note:

The replacement parts of this model is supplied as block unit.

Please use Troubleshooting Guide for your reference of the repair.

3.2. How to Update Firmware

The firmware of the unit may be renewed to improve the quality including operational performance and playability.

Make sure to refer the following procedure when performing version-up.

3.2.1. Confirmation of the Firmware Version

Perform following steps to checking the firmware version currently installed in the unit.

1. Turn the unit on and wait the Home screen is displayed.

2. Select [Setup] →[Player Settings] →[System] →[System Information] →[Firmware Version Information].

3. Firmware Version Information screen is displayed.

3.2.2. Updating Firmware

This unit has 2 updating method, one way to update via the internet, the other way to update using CD-R or USB device which is

stored pre-downloaded firmware update file.

3.2.2.1. Updating firmware via the internet

3.2.2.2. Updating firmware using the USB device

When updating firmware using USB device, perform following procedures.

(When using CD-R instead of USB device, perform same procedures)

1. Download the latest firmware file of the unit

The latest firmware required for version-up can be downloaded from “Support Information from NWBG/VDBG-PAVC” web-site

in “TSN system”

Click file name to download.

After download, click file to decompress. (Total: 1 file).

2. Decompress the downloaded file.

The decompressed file will be named as follows.

File Name: PANA_DVD.FRM

Copy the file to root folder of the USB device.

(If using CD-R instead of USB device, burn the file to a blank CD-R by writing software.)

3. Update the unit.

4 Specifications

Power supply: AC 120 V, 60 Hz

Power consumption: Approx. 15 W

In standby mode: Approx. 0.5 W

In quick start standby mode: Approx. 5 W

Operating temperature range: +5°C to +35°C (+41°F to +95°F)

Operating humidity range: 10 % to 80 % RH (no condensation)

Signal system: NTSC

Video output:

Output level: 1.0 Vp-p (75 Ω)

Output connector: Pin jack (1 system)

Audio output:

Output level: 2 Vrms (1 kHz, 0 dB)

Output connector: Pin jack

Number of connectors: 2 channel (1 system)

HDMI AV output:

Output format: 480p(525p)/576p(625p)/

1080i(1125i)/720p(750p)/

1080p(1125p)

This unit supports “HDMI CEC”

function.

Output connector: TypeA (19 pin): 1 system

USB slot:

USB2.0: DMP-BD87: 1 system

DMP-BD77: 2 system

Ethernet:

10BASE-T/100BASE-TX: 1 system

Wireless LAN:

Standard Compliance: IEEE802.11g / IEEE802.11b

/ IEEE802.11n

Frequency Range: 2.4GHz band

Security: WPA2-PSK(TKIP/AES)

* This unit supports WPA

and WPA2 encryption

WPA-PSK(TKIP/AES)

WEP(64bit/128bit)

LASER Specification

Class 1 LASER Product:

Wave length: 790 nm (CDs)/658 nm (DVDs)/

405 nm (BDs)

Laser power: No hazardous radiation is emitted

with the safety protection

Region management

information:

DVD-Video: region number “1” or “ALL”

BD-Video: region code “A”

Media:

Playable disc:

BD-Video (BD-LIVE): BD-ROM Version 2.4

BD-RE: Version3(Single Layer / Dual Layer),

JPEG

BD-R: Version2(Single Layer / Dual Layer),

MKV

DVD-R/DVD-R DL: DVD-Video format*1,

DVD Video Recording format*1,

AVCHD format*1, JPEG*2, FLAC,

MP3, MKV, WAV

DVD-RW: DVD-Video format*1,

DVD Video Recording format*1,

AVCHD format*1

+R/+RW/+R DL: Video*1, AVCHD format*1

DVD-Video: DVD-Video format

CD-Audio: CD-DA

CD-R/CD-RW: CD-DA, JPEG, FLAC, MP3,

MKV, WAV

*1 Finalizing is necessary.

USB device:

USB Standard: USB 2.0 High Speed

MP4,MPEG, MKV, JPEG, FLAC,

MP3, WAV

Format: FAT12, FAT16, FAT32, NTFS

Contents:

JPEG:

(CD-R/CD-RW, DVD-R/DVD-R DL, BD-RE, USB device)

File format: JPEG

(Motion JPEG and Progressive

JPEG are not supported.)

MP3:

(CD-R/CD-RW, DVD-R/DVD-R DL, USB device)

File format: MP3

MKV:

(CD-R/CD-RW, DVD-R/DVD-R DL, BD-R, USB device)

File format: MKV

FLAC:

(CD-R/CD-RW, DVD-R/DVD-R DL, USB device)

File format: FLAC

Maximum sampling rate: 192 kHz/24 bit

WAV:

(CD-R/CD-RW, DVD-R/DVD-R DL, USB device)

File format: WAV

Maximum sampling rate: 192 kHz/24 bit

AVCHD (H.264):

(DVD-R/DVD-R DL, DVD-RW, +R/+RW/+R DL)

File format: AVCHD format V1.0

Dimensions (WxHxD): 430mm x 36mm x 199mm

(Approx. 16 15/16” x 1 7/16” x

7 27/32”)

Mass: Approx. 1.5 kg (3.3 lbs)

Solder: This model uses lead free solder

(PbF).

Note: Specifications are subject to change

without notice.

4.1. Others (Licenses)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Blu-ray-Player Handbücher

Panasonic

Panasonic DMPBDT300 - 3D BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DP-UB420 Bedienungsanleitung

Panasonic

Panasonic DMP-BD75P Bedienungsanleitung

Panasonic

Panasonic DMP-BDT500 Bedienungsanleitung

Panasonic

Panasonic DMR-BWT720EB Bedienungsanleitung

Panasonic

Panasonic DMP-BDT281 Bedienungsanleitung

Panasonic

Panasonic DMP-BDT120 Bedienungsanleitung

Panasonic

Panasonic DMP-B15 - Portable Blu-ray Player Bedienungsanleitung

Panasonic

Panasonic DMP-BDT384 Bedienungsanleitung

Panasonic

Panasonic DMP-BD85 Bedienungsanleitung

Panasonic

Panasonic DMPBDT100 - 3D BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DMPB500 - PORTABLE BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DMPBDT100 - 3D BLU-RAY DISC PLAYER Bedienungsanleitung

Panasonic

Panasonic DMP-B15K Bedienungsanleitung

Panasonic

Panasonic DMP-B500EB Bedienungsanleitung

Panasonic

Panasonic DMP-BD84 Technische Daten

Panasonic

Panasonic DPUB820GNK Bedienungsanleitung

Panasonic

Panasonic DMR-BWT835GZ Bedienungsanleitung

Panasonic

Panasonic UltraHD DP-UB150 Bedienungsanleitung

Panasonic

Panasonic DMR-BWT740 Bedienungsanleitung

Panasonic

Panasonic DMR-HWT250 Bedienungsanleitung

Panasonic

Panasonic DMP-BD55; DMP-BD35 Bedienungsanleitung

Panasonic

Panasonic DP-UB9000 Technische Daten

Panasonic

Panasonic DP-UB9000GH1 Bedienungsanleitung

Beliebte Blu-ray-Player Handbücher anderer Marken

Samsung

Samsung BD-F5900 Bedienungsanleitung

Philips

Philips BDP3380K Bedienungsanleitung

Samsung

Samsung BD-P4600 Bedienungsanleitung

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Bedienungsanleitung

Pioneer

Pioneer BDP-140 Installations- und Betriebshandbuch

Samsung

Samsung BD-D8200A Bedienungsanleitung

LG HLX50W Bedienungsanleitung

Sony

Sony BDP-S300 - Blu-Ray Disc Player Bedienungsanleitung

Marantz

Marantz UD9004 Bedienungsanleitung

LG BD611 Bedienungsanleitung

Marantz

Marantz BD7004 Kurzanleitung

Kogan

Kogan KABRP3DWFIA Bedienungsanleitung

Toshiba

Toshiba BDX2700 Bedienungsanleitung

Samsung

Samsung BD-E5400 Bedienungsanleitung

Samsung

Samsung BD-F5100 Bedienungsanleitung

Philips

Philips BDP7100 Bedienungsanleitung

LG UBK80.DUSALLK Bedienungsanleitung