Panasonic Digital Palmcorder PV-DV101 Bedienungsanleitung

ORDERNO. VMD0102006C3

Digital Video Camcorder

PV-DV101 / PV-DV401

SPECIFICATIONS

Unauthorized copying and distribution isaviolation of law.

1. SAFETY PRECAUTIONS

GENERALGUIDELINES

1. IMPORTANTSAFETY NOTICE

There are special components used inthisequipment which are

important for safety. These parts are marked by inthe Schematic

Diagrams, CircuitBoard Layout, Exploded Viewsand

Replacement Parts List. Itisessential that these criticalparts

shouldbe replaced with manufacturer’sspecified parts to prevent

X-RADIATION, shock, fire, or other hazards. Donot modifythe

original design without permission of manufacturer.

2. AnIsolation Transformer shouldalwaysbe used during the

servicing of AC Adaptor whose chassisisnot isolated from the

AC power line. Use atransformer of adequate power rating as this

protects the technician from accidents resulting inpersonalinjury

from electrical shocks. Itwill also protect AC Adaptor from being

damaged byaccidental shorting that mayoccur during servicing.

3. When servicing, observe the original lead dress. Ifashort circuit

isfound, replace all parts which have been overheated or

damaged bythe short circuit.

4. After servicing, see to itthat all the protective devices such as

insulation barriers, insulation papers shields are properly

installed.

5. After servicing, make the following leakage current checks to

prevent the customer from being exposed to shock hazards.

LEAKAGE CURRENTCOLD CHECK

1. Unplug the AC cord and connect ajumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the

jumpered AC plug and each exposed metalliccabinet part on the

equipment such as screwheads, connectors, control shafts, etc.

When the exposed metallicpart has areturn path to thechassis,

the reading shouldbe between 1M and 5.2M . When the

exposed metal does not have areturn path to the chassis, the

reading must be infinity.

LEAKAGE CURRENTHOTCHECK

(See Figure 1.)

1. Plug the AC cord directlyinto the AC outlet. Donot use an

isolation transformer for thischeck.

2. Connect a1.5k , 10 Wresistor, inparallel with a0.15 F

capacitor, between each exposed metallicpart on the set and a

good earth ground, as showninFigure 1.

3. Use an AC voltmeter, with 1k /Vor more sensitivity, to measure

the potential across the resistor.

4. Check each exposed metallicpart, and measure the voltage at

each point.

5. Reverse the AC plug inthe AC outlet and repeat each of the above

measurements.

6. The potential at anypoint shouldnot exceed 0.75 VRMS. A

leakage current tester (Simpson Model 229 or equivalent) maybe

used to make the hot checks, leakage current must not exceed 1/2

mA. Incase ameasurement isoutside of thelimits specified, there

isapossibilityof ashock hazard, and the equipment shouldbe

repaired and rechecked before itisreturned to the customer.

Figure. 1

2. PREVENTION OF ELECTRO STATIC DISCHARGE

(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)

DEVICES

Some semiconductor(solidstate) devices canbe damagedeasilybystatic electricity. Such

components commonlyare calledElectrostaticallySensitive (ES) Devices. Examples of typical

ES devices are integratedcircuits and some field-effect transistorsand semiconductor"chip"

components. The following techniques shouldbe usedtohelpreduce the incidence of

component damage causedbyelectrostatic discharge (ESD).

1. Immediatelybefore handling anysemiconductor component or

semiconductor-equipped assembly, drainoff anyESDon your

bodybytouching aknownearth ground. Alternatively, obtainand

wear acommerciallyavailabledischarging ESDwrist strap,which

shouldbe removed for potential shock reasons prior to applying

power to the unitunder test.

2. After removing an electrical assemblyequipped with ES devices,

place the assemblyon aconductive surface such as aluminum

foil, to prevent electrostaticcharge buildup or exposure of the

assembly.

3. Use onlyagrounded-tipsoldering iron to solder or unsolder ES

devices.

4. Use onlyan antistaticsolder removal device. Some solder

removal devices not classified as "antistatic(ESDprotected)" can

generate electrical charge sufficient to damage ES devices.

5. Donot use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Donot remove areplacement ES device from its protective

package until immediatelybefore you are readyto install it. (Most

replacement ES devices are packaged with leads electrically

shorted together byconductive foam, aluminum foil or

comparableconductive material).

7. Immediatelybefore removing the protective material from the

leads of areplacement ES device, touch the protective material to

the chassisor circuitassemblyinto which the device will be

installed.

CAUTION :

Besure no power isapplied to the chassisor circuit, and observe

all other safetyprecautions.

8. Minimize bodilymotions when handling unpackaged replacement

ES devices. (Otherwise harmless motion such as the brushing

together of your clothes fabricor the lifting of your foot from a

carpeted floor can generate staticelectricity(ESD)sufficient to

damage an ES device).

3. X-RADIATION

(Formodel withMonochrome EVF)

WARNING :

1. The potential source of X-Radiation inEVF sets isthe High

Voltage section and the picture tube.

2. When using apicture tube test jigfor service, ensure that jigis

capableof handling 10 kV without causing X-Radiation.

NOTE :

Itisimportant to use an accurate periodicallycalibrated high

voltage meter.

3. Measure the High Voltage. The meter (electrostatictype) reading

shouldindicate 2.2kV±0.1kV. Ifthe meter indication isout of

tolerance, immediate service and correction isrequired to prevent

the possibilityof premature componentfailure. To prevent an X-

Radiation possibility, itisessential to use the specified picture

tube.

4. OPERATION GUIDE

5. SERVICE NOTES (PLEASE READ)

5.1. SERVICENOTES

5.1.1. EXTENSION CABLES FOR SERVICE POSITION

Using the following Extension Cables, place the unit as shownforcheck and service.

Extension Cables (No.5 ~ No.8) are usedforimproving serviceability. (Theyare not necessarily

used.)

Note :

1. The LCD open/close SW. isfor changing between LCD Displayor

EVF Display. When turning on LCD Display, place some paper or

tape, etc. on LCD open/close SW. so that thisSW. staysON.

2. (For earlyproducts)

Besure to attach the Short JIG C.B.A. on Connector B3. Refer to "

SHORT JIG C.B.A."

3. Use agrounded ESDwrist strap whiledisassembling the Lens

portion.

4. Use extreme care when unplugging or plugging inconnectors.

Fig. 1-1

5.1.2. INTERCONNECTION OFEXTENSION CABLES

Fig. 1-2

5.1.3. SIMPLIFIED FAULT FINDING DATA (SELF-DIAGNOSTIC SYSTEM)

When following conditions occur, the Power LEDwill flash

according to the condition. Fig. 2-1

Ifanyof the following numbers appear on-screen, the palmcorder

mayneed service. Donot remove the battery(ifattached) and write

downthe displayed number. Fig. 2-2

Note:

Whilebatteryremains, the Error No. will be displayed againwhen

the power isswitched off and on again. (Once the Batteryis

removed or dead, Error No. will not remaininthe memory.)

5.1.4. SHORTJIG C.B.A.

(Forearlyproducts)

Purpose of the Short JIG C.B.A.

Inordertoprevent the breaking of the FlashROM due toESD

(ElectroStatic Discharge), the Short JIG C.B.A. is installedtothe connectorB3 on the Main

C.B.A.

Forearlyproducts, the FlashROM has beenusedforDSC microcontroller(IC401) and System

Control microcontroller(IC6001).

Whenthe FlashROM is usedforeitherorbothmicrocontroller(s), be sure toattachthe Short

JIG C.B.A. tothe connectorB3 on the MainC.B.A. (Otherwise, the comcordercannot be turned

on.)

Fordistinction, check whetherthe connectorB3 is usedon the MainC.B.A. ornot.

Whenthe B3 connectoris on the MainC.B.A., the FlashROM is usedforeitherorbothIC401 and

/orIC6001.

1. Open the LCD Unit.

2. Remove 2Screws(A). Then open the Right Cover Unit.

3. Install the Short JIG C.B.A. to the Connector B3.

Fig. 3

5.1.5. REMOVAL/INSTALLATION OFF.P.C. FROM NON ZIF(ZeroInsertion

Force) CONNECTOR

Removal/Installation of F.P.C. fromthe Non ZIF(ZeroInsertion Force) connector:

1. To remove the F.P.C. from the Non ZIFconnector, use the Plier for

Non ZIFConnector (LSVQ0028) to pull out the F.P.C. as shown.

The same Plier for Non ZIFConnector (LSVQ0028) shouldalso be

Andere Handbücher für Digital Palmcorder PV-DV101

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Camcorder Handbücher

Panasonic

Panasonic NV-M7EA Bedienungsanleitung

Panasonic

Panasonic Palmcorder PV-L857 Bedienungsanleitung

Panasonic

Panasonic 456 Bedienungsanleitung

Panasonic

Panasonic NV-GS38GK Bedienungsanleitung

Panasonic

Panasonic NV MX 2 B Bedienungsanleitung

Panasonic

Panasonic AVCCAM AG-AC90 Bedienungsanleitung

Panasonic

Panasonic HC-V260 Technische Daten

Panasonic

Panasonic Palmcorder IQ PV-A306 Bedienungsanleitung

Panasonic

Panasonic HDC-SDT750PP Bedienungsanleitung

Panasonic

Panasonic PV-DV952 Bedienungsanleitung

Panasonic

Panasonic AGHPX500P - MEMORY CARD CAMERA RECORDER Installationsanleitung

Panasonic

Panasonic AWE800 - COLOR CAMERA Bedienungsanleitung

Panasonic

Panasonic AW-HE42WP Bedienungsanleitung

Panasonic

Panasonic SDR-H18P Bedienungsanleitung

Panasonic

Panasonic P2HD AG-HPX600 Installationsanleitung

Panasonic

Panasonic Palmcorder PV-L557 Bedienungsanleitung

Panasonic

Panasonic VDRM95PP - DVD MOVIE CAMERA Bedienungsanleitung

Panasonic

Panasonic AK-HC3900 Gebrauchs- und Pflegehandbuch

Panasonic

Panasonic NV-GS33GC Bedienungsanleitung

Panasonic

Panasonic DVD Palmcorder Camcorder VDR-D310 Bedienungsanleitung

Panasonic

Panasonic AW-HE20WP Bedienungsanleitung

Panasonic

Panasonic Palmcorder Palmsight PV-L600 Bedienungsanleitung

Panasonic

Panasonic HC-V130 Bedienungsanleitung

Panasonic

Panasonic NVVS4EG Bedienungsanleitung

Beliebte Camcorder Handbücher anderer Marken

Toshiba

Toshiba CAMILEO Z100 Bedienungsanleitung

Canon

Canon RC 260 Bedienungsanleitung

Sony

Sony Handycam DCR-DVD7E Bedienungsanleitung

Brinno

Brinno TimeLapse TLC200 Bedienungsanleitung

JVC

JVC GR-SXM68AC Kurzanleitung

MYDLINK

MYDLINK DCS-6100LH Bedienungsanleitung

Sony

Sony video Hi8 Handycam CCD-TR555 Bedienungsanleitung

SECURECOM

SECURECOM V-5014B Bedienungsanleitung

Sharper Image

Sharper Image U-VIDEO Bedienungsanleitung

JVC

JVC AA-V15EG Bedienungsanleitung

Canon

Canon LEGRIA HV40 Bedienungsanleitung

Sony

Sony Handycam DCR-VX2000 Bedienungsanleitung

RCA

RCA CC616 Bedienungsanleitung

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung

ATIK Cameras

ATIK Cameras Horizon Bedienungsanleitung

Sony

Sony Handycam HDR-CX580V Bedienungsanleitung

Sharp

Sharp ViewcamZ VL-Z8H Bedienungsanleitung

Philips

Philips M620/21 Bedienungsanleitung