Panasonic SDR-H200PC Bedienungsanleitung

rights reserved. Unauthorized copying and

distribution is a violation of law.

Vol. 1

Colours

(S)...................Silver Type

SD Card/Hard Disk Video Camera

ORDER NO. MKE0703302CE

B27

1 Safety Precautions 3

1.1. General Guidelines 3

2 Warning 4

2.1. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices 4

2.2. How to Recycle the Lithium Battery 4

2.3. How to Replace the Lithium Battery 5

3 Service Navigation 6

3.1. Introduction 6

3.2. About Lead Free Solder (PbF) 6

3.3. Precautions for Handling HDD 7

3.4. Formatting HDD 11

4 Specifications 12

5 Service Mode 13

5.1. Error Display 13

5.2. Service Menu 13

5.3. About Default Setting 18

6 Service Fixture & Tools 19

6.1. Service Fixture and Tools 19

6.2. Service Position 20

6.3. Removal/Installation of F.P.C. From Non ZIF (Zero

Insertion Force) Connector 23

6.4. EEPROM Data 24

6.5. Special Note 25

6.6. Model No. Identification Mark 25

7 Disassembly and Assembly Instructions 26

7.1. Disassembly Flow Chart 26

7.2. P.C.B. Layout 26

7.3. Disassembly Procedures 27

8 Measurements and Adjustments 33

8.1. Electrical Adjustment 33

9 Maintenance 36

9.1. Cleaning Lens and LCD Panel 36

10 Troubleshooting 37

11 Voltage Chart of Connectors on Sub P.C.B. and Main P.C.B.

12 Block Diagrams 51

13 Schematic Diagrams 53

13.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT

NOTES 53

13.2. FRONT SCHEMATIC DIAGRAM 54

13.3. LCD BACKLIGHT SCHEMATIC DIAGRAM 55

13.4. HDD RELAY SCHEMATIC DIAGRAM 56

13.5. SIDE R / LCD OPEN SWITCH SCHEMATIC DIAGRAM

13.6. CCD SCHEMATIC DIAGRAMS 58

13.7. REAR CASE / SHAFT FPC / HDD RELAY FPC

SCHEMATIC DIAGRAMS 59

13.8. SIDE L / OPERATION / TOP OPERATION SCHEMATIC

DIAGRAMS 60

13.9. INTERCONNECTION SCHEMATIC DIAGRAM 61

14 Printed Circuit Board 63

14.1. FRONT P.C.B. 63

14.2. HDD RELAY P.C.B. 64

14.3. LCD BACKLIGHT P.C.B. 65

14.4. SIDE R P.C.B. 66

14.5. OPEN SWITCH P.C.B. 67

15 Exploded View 69

15.1. MAIN PARTS SECTION 69

15.2. FRONT HOOD AND FRONT P.C.B. SECTION 70

15.3. SIDE R OPERATION AND LCD SECTION 71

15.4. CCD AND LENS SECTION 72

15.5. PACKING PARTS AND ACCESSORIES SECTION 73

16 Replacement Parts Lists 74

16.1. REPLACEMENT NOTES 74

16.2. MECHANICAL REPLACEMENT PARTS LIST 75

16.3. ELECTRICAL REPLACEMENT PARTS LIST 75

CONTENTS

Page Page

SDR-H200P / SDR-H200PC

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment

which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essential

that these critical parts should be replaced with

manufacturer’s specified parts to prevent shock, fire, or

other hazards. Do not modify the original design without

permission of manufacturer.

2. An Isolation Transformer should always be used during the

servicing of AC Adaptor whose chassis is not isolated from

the AC power line. Use a transformer of adequate power

rating as this protects the technician from accidents

resulting in personal injury from electrical shocks. It will also

protect AC Adaptor from being damaged by accidental

shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such

as insulation barriers, insulation papers shields are properly

installed.

5. After servicing, make the following leakage current checks

to prevent the customer from being exposed to shock

hazards.

SDR-H200P / SDR-H200PC

2 Warning

2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage

caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable

conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)

sufficient to damage an ES device).

2.2. How to Recycle the Lithium Battery

SDR-H200P / SDR-H200PC

2.3. How to Replace the Lithium Battery

1. Remove the Side R P.C.B.. (Refer to Disassembly Procedures.)

2. Unsolder the Lithium Battery “ML-621S/F9D” and then replace the new one.

NOTE:

This Lithium battery is a critical component. (Type No.: ML-621S/F9D Manufactured by Panasonic.)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in equipment designed specifically for its use.

Replacement batteries must be of the same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

SDR-H200P / SDR-H200PC

3 Service Navigation

3.1. Introduction

This service manual contains technical information which will allow service personnel´s to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service

manual.

Note 1:

AC Adaptor used on these movie camera is PV-DAC14D. However, DE-974FB is supplied as a replacement part for PV-

DAC14D. This AC Adaptor is supplied only as a unit.

3.2. About Lead Free Solder (PbF)

SDR-H200P / SDR-H200PC

3.3. Precautions for Handling HDD

1. Handle HDD very carefully to prevent the static electricity and shock.

2. Set the HDD quickly after taking it out from the package. Make sure to put the HDD on buffer materials, etc.

3.3.1. Precautions at incoming process and for opening packages

SDR-H200P / SDR-H200PC

3.3.2. Precautions for installing HDD

SDR-H200P / SDR-H200PC

3.3.3. Precautions for inserting and removing HDD FPC

Make sure to use the tool (LSVQ0112) when locking and unlocking the lock lever of HDD FPC connector.

Do not lock the lock lever without inserting HDD FPC. Otherwise, the connector may be damaged.

SDR-H200P / SDR-H200PC

Make sure to use the tool (LSVQ0112) when opening and closing the lock lever.

*See "Disassembly Procedures" (Fig. D4) for attaching to the unit.

SDR-H200P / SDR-H200PC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Camcorder Handbücher

Panasonic

Panasonic HC-V500 Bedienungsanleitung

Panasonic

Panasonic HDC-TM700K Bedienungsanleitung

Panasonic

Panasonic AG- DVC 15P Bedienungsanleitung

Panasonic

Panasonic VDR VDR-D220 Kurzanleitung

Panasonic

Panasonic Palmcorder MultiCam PV-DV852 Bedienungsanleitung

Panasonic

Panasonic VDR-D150GN Bedienungsanleitung

Panasonic

Panasonic NV-GS150EG Bedienungsanleitung

Panasonic

Panasonic VDR-D150EE null

Panasonic

Panasonic HC-V270 Bedienungsanleitung

Panasonic

Panasonic NV-M5AM Bedienungsanleitung

Panasonic

Panasonic NV-GS35EB Bedienungsanleitung

Panasonic

Panasonic SVAV10U - SD MULTI AV DEVICE Bedienungsanleitung

Panasonic

Panasonic PV-GS33PP Bedienungsanleitung

Panasonic

Panasonic AJ-D400P Bedienungsanleitung

Panasonic

Panasonic NV-RZ1EG/B/E/EN/ENC/A Bedienungsanleitung

Panasonic

Panasonic NV-DS11EN Bedienungsanleitung

Panasonic

Panasonic HC-V500MP Bedienungsanleitung

Panasonic

Panasonic Digital Palmcorder PV-GS150 Bedienungsanleitung

Panasonic

Panasonic NV-GS60E Bedienungsanleitung

Panasonic

Panasonic AVCCAM AG-HMC150P Bedienungsanleitung

Panasonic

Panasonic AVCCAM AG-HMR10 Bedienungsanleitung

Panasonic

Panasonic AJSDC915 - DVC PRO CAMCORDER Bedienungsanleitung

Panasonic

Panasonic 456 Bedienungsanleitung

Panasonic

Panasonic HC-W850P Montage- und Serviceanleitung

Beliebte Camcorder Handbücher anderer Marken

Toshiba

Toshiba CAMILEO Z100 Bedienungsanleitung

Canon

Canon RC 260 Bedienungsanleitung

Sony

Sony Handycam DCR-DVD7E Bedienungsanleitung

Brinno

Brinno TimeLapse TLC200 Bedienungsanleitung

JVC

JVC GR-SXM68AC Kurzanleitung

MYDLINK

MYDLINK DCS-6100LH Bedienungsanleitung

Sony

Sony video Hi8 Handycam CCD-TR555 Bedienungsanleitung

SECURECOM

SECURECOM V-5014B Bedienungsanleitung

Sharper Image

Sharper Image U-VIDEO Bedienungsanleitung

JVC

JVC AA-V15EG Bedienungsanleitung

Canon

Canon LEGRIA HV40 Bedienungsanleitung

Sony

Sony Handycam DCR-VX2000 Bedienungsanleitung

RCA

RCA CC616 Bedienungsanleitung

Insignia

Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung

ATIK Cameras

ATIK Cameras Horizon Bedienungsanleitung

Sony

Sony Handycam HDR-CX580V Bedienungsanleitung

Sharp

Sharp ViewcamZ VL-Z8H Bedienungsanleitung

Philips

Philips M620/21 Bedienungsanleitung