Panasonic H-RS100400 Bedienungsanleitung

Owner’s Manual

INTERCHANGEABLE LENS FOR DIGITAL CAMERA

Model No. H-RS100400

until

2016/2/04

Please read these instructions carefully before using this product, and save this manual for future use.

If you have any questions, visit:

USA : http://shop.panasonic.com/support

Canada : www.panasonic.ca/english/support

SQT1199-1

F0116YD1066

SQT1199_ENG_Cover.fm 1 ページ２０１６年５月２４日　火曜日　午後３時５５分

SQT1199 (ENG)

Contents

Information for Your Safety................................ 2

Precautions...................................................... 4

Supplied Accessories ........................................ 5

Names and Functions of Components .............. 6

Attaching/Detaching the Lens............................ 7

Using the Lens Hoods ....................................... 7

Using the Tripod Mount ..................................... 9

Cautions for Use.............................................. 10

Troubleshooting............................................. 10

Specifications ..................................................11

Limited Warranty ............................................. 12

THE FOLLOWING APPLIES ONLY IN CANADA.

Information for Your Safety

Keep the unit as far away as possible from

electromagnetic equipment (such as microwave ovens,

TVs, video games, radio transmitters, high-voltage

lines etc.).

• Do not use the camera near cell phones because doing so

may result in noise adversely affecting the pictures and

sound.

• If the camera is adversely affected by electromagnetic

equipment and stops functioning properly, turn the camera

off and remove the battery and/or the connected AC

adaptor. Then reinsert the battery and/or reconnect the AC

adaptor and turn the camera on.

The lens can be used with a digital camera compatible with

the lens mount standard for the “Micro Four ThirdsTM

System”.

• It cannot be mounted on the Four ThirdsTM mount

specification camera.

• The digital camera illustrations in this owner’s manual

show DMC-GH4 as an example.

• The appearance and specifications of products described

in this manual may differ from the actual products you

have purchased due to later enhancements.

• Micro Four ThirdsTM and Micro Four Thirds Logo marks

are trademarks or registered trademarks of Olympus

Imaging Corporation, in Japan, the United States, the

European Union and other countries.

CAN ICES-3(B)/NMB-3(B)

SQT1199_ENG_SPA.book 2 ページ２０１６年１月１８日　月曜日　午後５時３５分

(ENG) SQT1199

• Four ThirdsTM and Four Thirds Logo marks are trademarks

or registered trademarks of Olympus Imaging Corporation,

in Japan, the United States, the European Union and other

countries.

• G MICRO SYSTEM is an interchangeable lens type digital

camera system of LUMIX based on a Micro Four Thirds

System standard.

• LEICA is a registered trademark of Leica Microsystems IR

GmbH. ELMAR is a registered trademark of Leica Camera

AG. The LEICA DG lenses are manufactured using

measurement instruments and quality assurance systems

that have been certified by Leica Camera AG based on the

company’s quality standards.

• Other names of systems and products mentioned in these

instructions are usually the registered trademarks or

trademarks of the manufacturers who developed the

system or product concerned.

THE FOLLOWING APPLIES ONLY IN THE U.S.A.

FCC Note:

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Any unauthorized changes or modifications to this equipment

would void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Responsible Party:

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ 07102-5490

Support Contact:

http://www.panasonic.com/contactinfo

ENGLISH

SQT1199_ENG_SPA.book 3 ページ２０１６年１月１８日　月曜日　午後５時３５分

SQT1199 (ENG)

∫Lens Care

• This lens has a dust-proof and splash-proof construction.

When using it, please be careful of the following.

If the lens is not working properly, consult the dealer or

your nearest Service Center.

– Please attach the lens to a dust-proof and splash-proof

digital camera.

– When detaching the lens from the digital camera, take

care to ensure that sand, dust, splashes of water etc., do

not get into the lens or the terminals.

– When using the built-in slide lens hood, ensure that

particles such as sand and dust do not stick to the

lens barrel, where the built-in slide lens hood slides.

– This lens is not waterproof and cannot be used to record

underwater. For splash-proofing, the lens is constructed

to resist the entry of water. If splashes of water etc. do

adhere to the lens, wipe after use with a soft dry cloth.

• To improve the dust-proofing and splash-proofing of this

lens, a lens mount rubber is used in the mounting portion.

After changing the lens a number of times, you may find

that the lens mount rubber has marked the mount portion

of the digital camera body, which does not affect its

performance.

For information on changing the lens mount rubber,

contact your nearest Service Center.

• Do not press the lens with excessive force.

• When there is dirt (water, oil, and fingerprints, etc.) on the

surface of the lens, the picture may be affected. Lightly

wipe the surface of the lens with a soft, dry cloth before

and after taking pictures.

• To prevent dust and other particles from accumulating on

or entering the lens, attach the lens rear cap when the lens

is not in use.

• To protect the lens contact points 1, do not place the lens

with its mount surface facing down. In addition, do not

allow the lens contact points to become dirty.

Precautions

SQT1199_ENG_Body.fm 4 ページ２０１６年５月２４日　火曜日　午後３時５７分

(ENG) SQT1199

∫About Condensation (Fogging of the Lens)

• Condensation occurs when there are differences in

temperature and humidity as described below.

Condensation can cause the lens to become dirty and

lead to mold and malfunctioning, so exercise caution in the

following situations:

– When the camera is brought indoors from outside during

cold weather

– When the camera is brought into an air-conditioned car

– When cold air from an air conditioner is directly blown

onto the lens

– In humid places

• If condensation occurs, turn the power off and leave it for

about two hours. Once the camera acclimatizes to the

surrounding temperature the condensation will go away

naturally.

Supplied Accessories

Product numbers correct as of January 2016. These may

be subject to change.

1Lens Pouch

2Lens Hood

3Lens Cap

4Lens Rear Cap

5External tripod mount

• The lens rear cap and lens cap are attached to the

interchangeable lens at the time of purchase.

SFC0360

SYQ0679

SYF0074 VFC4605

SYQ0680

SQT1199_ENG_SPA.book 5 ページ２０１６年１月１８日　月曜日　午後５時３５分

SQT1199 (ENG)

Names and Functions of

Components

1Lens surface

2Built-in slide lens hood (P7)

3Focus ring

Rotate to focus when taking pictures with manual focus (MF).

4Zoom lock ring

When carrying the lens, rotate this ring to lock the zoom ring

to prevent the lens from extending under its own weight.

• Do not rotate the zoom ring when the zoom lock ring is set

to [LOCK].

5Zoom ring

Rotate the zoom ring when you wish to take large (tele) or

wide (wide angle) pictures.

6Tripod mount (P9)

7Orientation locking knob (P9)

8O.I.S. switch

When the lens is attached to the camera the stabilizer

function is set to activate if the O.I.S. switch is set to [ON].

• We recommend setting the O.I.S. switch to [OFF] when

using a tripod.

9[AF/MF] switch

This allows you to switch between Auto Focus (AF) and

Manual Focus (MF).

• When either the [AF/MF] switch of the lens or the setting of

the camera is set to [MF], Manual Focus (MF) is enabled.

10 Focusing distance range selector switch

[FULL]: It can focus between the ranges of 1.3 m

(4.27 feet) to ¶.

[5m-¶]:It can focus between the ranges of 5.0 m

(16.4 feet) to ¶. The speed of focusing with

auto focus will be faster.

11 Lens fitting mark

12 Lens mount rubber

13 Contact points

1 2 3 4 5 6 7 8 910

[LOCK]: Locks the zoom ring.

[UNLOCK]: Unlocks the zoom ring.

SQT1199_ENG_SPA.book 6 ページ２０１６年１月１８日　月曜日　午後５時３５分

(ENG) SQT1199

Note

• If you zoom after focusing, focusing errors may occur.

After zooming, please perform the focusing again.

• In very quiet situations Auto Focus operating sounds may

be recorded during motion picture recording. This is not a

malfunction. In such situations, switching to Manual Focus

will improve the situation.

• If you set the O.I.S. to [ON] when recording a motion

picture, operating sounds may be recorded. If they

become bothersome, we recommend setting the O.I.S.

switch to [OFF] and mounting the camera on a tripod.

Attaching/Detaching the Lens

For information on how to attach and remove the lens,

refer to the owner’s manual for your digital camera.

• Before attaching or detaching the lens, check that the

digital camera is turned off.

• Before attaching the lens to the digital camera, remove the

lens rear cap. (1, 2)

• To prevent dust and other particles from accumulating on

or entering the lens, be sure to attach the lens cap/lens

rear cap after detaching the lens from the digital camera.

∫Attaching Filters

• Vignetting may occur if using 2 or more filters at the same

time.

• It is possible to attach the lens cap or the supplied lens

hood with the filter already attached.

• You cannot attach a conversion lens or adaptor to this

lens. A filter may be used, but attaching any other element

may cause damage to the lens.

Using the Lens Hoods

The lens comes with a built-in slide lens hood and supplied

lens hood. With the latter, you can block extra light even

more effectively.

• The built-in slide lens hood and supplied lens hood can be

used together at the same time.

• To use the built-in slide lens

hood, slide it in the direction of

the arrow.

We recommend locking the

zoom ring with the zoom lock

ring before performing

operations.

SQT1199_ENG_Body.fm 7 ページ２０１６年５月２４日　火曜日　午後３時５８分

SQT1199 (ENG)

∫

Attaching the Lens Hood (Supplied Accessory)

1Rotate the lens hood screw in the direction of

the arrow to loosen it (1).

2 Insert the lens hood until it stops (2).

3 Rotate the lens hood screw in the

direction of the arrow to fasten the lens

hood securely (3).

Note

• When using the lens with the supplied lens hood, check if

the lens hood screw has become loose.

• If you use a lens hood and the flash at the same time, the

lens hood will block the light from the flash, causing the lower

portion of the screen to darken (vignetting) and making it

impossible to adjust the amount of light. We recommend not

using the lens hoods and flash at the same time.

• When carrying, the supplied lens

hood can be temporarily attached

in the reverse direction.

• Do not carry the lens

by holding only the

built-in slide lens

hood or the supplied

lens hood.

SQT1199_ENG_SPA.book 8 ページ２０１６年１月１８日　月曜日　午後５時３５分

(ENG) SQT1199

Using the Tripod Mount

Attach a tripod to the tripod

mount of the lens and not to

that of the digital camera.

If the lens or digital camera

prevents the tripod from being

attached, attach the supplied external tripod mount to the

lens.

• When a battery grip (DMW-BGGH3) is in use, for example,

it will come in contact with the head of your tripod,

preventing the tripod from being attached. In this case,

attach the supplied external tripod mount to the lens.

• An interface unit (DMW-YAGH/AG-YAGH) will also

prevent a tripod from being attached even if you use the

external tripod mount. In this case, attach your tripod to

the appropriate tripod hole on the interface unit.

∫Attaching the external tripod mount (supplied)

1Insert the external tripod mount attachment

screw (1) into the tripod mount of the lens.

Rotate the external tripod mount attachment

screw in the direction of the arrows to fasten it

firmly.

• Check that the external tripod mount attachment screw is

not loose before use.

∫Changing the vertical/horizontal orientation

You can loosen the orientation locking knob (1) to rotate

the lens together with the digital camera (2).

This way, you can quickly switch between the vertical and

horizontal orientation while the tripod is in use.

• After changing the orientation, tighten the orientation

locking knob firmly and check that it is not loose.

SQT1199_ENG_SPA.book 9 ページ２０１６年１月１８日　月曜日　午後５時３５分

SQT1199 (ENG)

Cautions for Use

Take care not to drop or knock the lens. Also take care

not to put a lot of pressure on the lens.

• Take care not to drop the bag that you inserted the lens in

as it may strongly shock the lens. The camera may stop

operating normally and pictures may no longer be

recorded. Also, the lens may be damaged.

• When carrying the digital camera with the lens attached,

hold both the digital camera and the lens.

When using pesticides and other volatile substances

around the camera make sure that they do not get onto

the lens.

• If such substances get onto the lens they can damage the

exterior case or cause the paint to peel.

Do not point the lens at the sun or other strong light

sources.

• This could cause the lens to collect an excessive amount

of light, resulting in fire and malfunction.

• Under no circumstances should the unit be stored in any

of the following locations since doing so may cause

problems in operation or malfunctioning.

– In direct sunlight or on a beach in summer

– In locations with high temperatures and humidity levels or

where the changes in temperature and humidity are acute

– In locations with high concentrations of sand, dust or dirt

– Where there is fire

– Near heaters, air conditioners or humidifiers

– Where water may make the unit wet

– Where there is vibration

– Inside a vehicle

• Refer also to the owner’s manual of the digital camera.

• When the unit is not going to be used for a prolonged

period, we recommend storing with a desiccant (silica gel).

Failure to do so may result in performance failure caused

by mold, etc. It is recommended that you check the unit’s

operation prior to use.

• Do not leave the lens in contact with rubber or plastic

products for extended periods of time.

• Do not touch the lens contact point. Doing so can cause

failure of the unit.

• Do not disassemble or alter the unit.

Do not use benzine, thinner, alcohol or other similar

cleaning agents to clean the lens glass or exterior

cabinet.

• Using solvents can damage the lens or cause the paint to

peel.

• Wipe off any dust or fingerprints with a soft, dry cloth.

• Use a dry, dust cloth to remove dirt and dust on the lens

mount rubber, zoom ring, zoom lock ring, focus ring, or

built-in slide lens hood.

• Do not use a household detergent or a chemically treated

cloth.

When I turn on or off the camera or when I shake the

lens, I hear a sound, for example a rattling sound.

• This is the sound of lens or aperture movement and is not

a malfunction.

Troubleshooting

SQT1199_ENG_SPA.book 10 ページ２０１６年１月１８日　月曜日　午後５時３５分

Andere Handbücher für H-RS100400

Inhaltsverzeichnis

Sprachen:

Andere Panasonic Kameraobjektiv Handbücher

Panasonic

Panasonic 5025232847358 Bedienungsanleitung

Panasonic

Panasonic H-HS043 Bedienungsanleitung

Panasonic

Panasonic Lumix H-FSA14140 Bedienungsanleitung

Panasonic

Panasonic LUMIX H-F007014E Bedienungsanleitung

Panasonic

Panasonic H-H025 Bedienungsanleitung

Panasonic

Panasonic Lumix DMW-STC14 Bedienungsanleitung

Panasonic

Panasonic Lumix H-F008 Bedienungsanleitung

Panasonic

Panasonic H-HS030PP Bedienungsanleitung

Panasonic

Panasonic LUMIX H-X015K Bedienungsanleitung

Panasonic

Panasonic Lumix S Pro S-R1635 Bedienungsanleitung

Panasonic

Panasonic H-HS030 Bedienungsanleitung

Panasonic

Panasonic Lumix H-H014 Bedienungsanleitung

Panasonic

Panasonic H-FS35100PP Bedienungsanleitung

Panasonic

Panasonic ET-D3LEW10C Bedienungsanleitung

Panasonic

Panasonic ET-DLE060 Bedienungsanleitung

Panasonic

Panasonic Lumix H-XA025 Bedienungsanleitung

Panasonic

Panasonic WV-LZ62/8S Bedienungsanleitung

Panasonic

Panasonic Lumix S-E2470 Installationsanleitung

Panasonic

Panasonic Lumix H-ES12060 Bedienungsanleitung

Panasonic

Panasonic 5025232921027 Bedienungsanleitung

Panasonic

Panasonic Lumix H-FT012 Bedienungsanleitung

Panasonic

Panasonic H-FS045200 - Lumix Telephoto Zoom Lens Bedienungsanleitung

Panasonic

Panasonic DMWLWA52 Bedienungsanleitung

Panasonic

Panasonic H-H025 Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung

Sinar

Sinar Rolleiflex 6008 AF Bedienungsanleitung

Rokinon

Rokinon SP 85mm F1.2 Bedienungsanleitung