Panasonic H-X012 Bedienungsanleitung

SQT1299

F0616KD0

Operating Instructions

INTERCHANGEABLE LENS FOR DIGITAL CAMERA

Model No. H-X012

Please read these instructions carefully before using this product, and save this manual for future use.

until

2016/06/22

SQT1299_E.book 1 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

Contents

Information for Your Safety................................ 2

Precautions...................................................... 3

Supplied Accessories ........................................ 4

Names and Functions of Components .............. 5

Attaching/Detaching the Lens............................ 6

Using the Lens Hoods ....................................... 6

Cautions for Use................................................8

Troubleshooting............................................... 8

Specifications .................................................... 9

Limited Warranty (ONLY FOR AUSTRALIA)... 10

Information for Your Safety

Keep the unit as far away as possible from electromagnetic

equipment (such as microwave ovens, TVs, video games,

radio transmitters, high-voltage lines etc.).

• Do not use the camera near cell phones because doing so

may result in noise adversely affecting the pictures and

sound.

• If the camera is adversely affected by electromagnetic

equipment and stops functioning properly, turn the camera

off and remove the battery and/or the connected AC

adaptor. Then reinsert the battery and/or reconnect the AC

adaptor and turn the camera on.

The lens can be used with a digital camera compatible with the

lens mount standard for the “Micro Four Thirds

System”.

• It cannot be mounted on the Four ThirdsTM mount

specification camera.

• The appearance and specifications of products described

in this manual may differ from the actual products you

have purchased due to later enhancements.

• Micro Four ThirdsTM and Micro Four Thirds Logo marks

are trademarks or registered trademarks of Olympus

Imaging Corporation, in Japan, the United States, the

European Union and other countries.

• Four ThirdsTM and Four Thirds Logo marks are trademarks

or registered trademarks of Olympus Imaging Corporation,

in Japan, the United States, the European Union and other

countries.

• G MICRO SYSTEM is an interchangeable lens type digital

camera system of LUMIX based on a Micro Four Thirds

System standard.

• LEICA is a registered trademark of Leica Microsystems IR

GmbH.

SUMMILUX

is a registered trademark of Leica

Camera AG. The LEICA DG lenses are manufactured

using measurement instruments and quality assurance

systems that have been certified by Leica Camera AG

based on the company’s quality standards.

• Other names of systems and products mentioned in these

instructions are usually the registered trademarks or

trademarks of the manufacturers who developed the

system or product concerned.

SQT1299_E.book 2 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

-If you see this symbol-

∫Lens Care

• This lens has a dust-proof and splash-proof construction.

When using it, please be careful of the following.

If the lens is not working properly, consult the dealer or

your nearest Service Centre.

– Please attach the lens to a dust-proof and

splash-proof digital camera.

– When detaching the lens from the digital camera,

take care to ensure that sand, dust, splashes of

water etc., do not get into the lens or the

terminals.

– This lens is not waterproof and cannot be used to

record underwater. For splash-proofing, the lens

is constructed to resist the entry of water. If

splashes of water etc. do adhere to the lens, wipe

after use with a soft dry cloth.

• To improve the dust-proofing and splash-proofing of this

lens, a lens mount rubber is used in the mounting portion.

After changing the lens a number of times, you may find

that the lens mount rubber has marked the mount portion

of the digital camera body, which does not affect its

performance.

For information on changing the lens mount rubber,

contact your nearest Service Centre.

• Do not press the lens with excessive force.

• To prevent dust and other particles from accumulating on

or entering the lens, attach the lens rear cap when the lens

is not in use.

Disposal of Old Equipment

Only for European Union and countries with recycling

systems

This symbol on the products, packaging, and/or

accompanying documents means that used

electrical and electronic products must not be

mixed with general household waste.

For proper treatment, recovery and recycling of

old products, please take them to applicable collection

points in accordance with your national legislation.

By disposing of them correctly, you will help to save

valuable resources and prevent any potential negative

effects on human health and the environment.

For more information about collection and recycling,

please contact your local municipality.

Penalties may be applicable for incorrect disposal of this

waste, in accordance with national legislation.

Precautions

ENGLISH

SQT1299_E.book 3 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

• To protect the lens contact points 1, do not place the lens

with its mount surface facing down. In addition, do not

allow the lens contact points to become dirty.

∫About Condensation (Fogging of the Lens)

• Condensation occurs when there are differences in

temperature and humidity as described below.

Condensation can cause the lens to become dirty and

lead to mold and malfunctioning, so exercise caution in the

following situations:

– When the camera is brought indoors from outside during

cold weather

– When the camera is brought into an air-conditioned car

– When cold air from an air conditioner is directly blown

onto the lens

– In humid places

• If condensation occurs, turn the power off and leave it for

about two hours. Once the camera acclimatizes to the

surrounding temperature the condensation will go away

naturally.

Supplied Accessories

Product numbers correct as of June 2016. These may be

subject to change.

1Lens Pouch

2Lens Cap

3Lens Rear Cap

4Lens Hood

• The lens rear cap and lens cap are attached to the

interchangeable lens at the time of purchase.

VFC4430

SYF0083

2134

VFC4605 SYA0067

SQT1299_E.book 4 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

Names and Functions of

Components

1Lens surface

2Aperture ring

Rotate this to adjust the aperture value.

• If you set the camera to Aperture-Priority AE Mode or

Manual Exposure Mode, the aperture value of the ring will

be enabled.

• If you set the position of the aperture ring to [A], the

aperture value of the camera will be enabled.

3Focus ring

Rotate to focus when taking pictures with manual focus (MF).

4[AF/MF] switch

This allows you to switch between Auto Focus (AF) and

Manual Focus (MF).

• When either the [AF/MF] switch of the lens or the setting of

the camera is set to [MF], Manual Focus (MF) is enabled.

5Lens fitting mark

6Contact points

7Lens mount rubber

Note

• When you take pictures with the camera’s flash, the

periphery of the screen may appear dark. In that case, we

recommend using an external flash.

• In very quiet situations Auto Focus operating sounds may

be recorded during motion picture recording. This is not a

malfunction. In such situations, switching to Manual Focus

will improve the situation.

• The aperture can be adjusted with the aperture ring only

when a Panasonic digital camera is attached to the lens.

(As of June 2016)

1 2 3

6 7

SQT1299_E.book 5 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

Attaching/Detaching the Lens

For information on how to attach and remove the lens,

refer to the operating instructions for your digital

camera.

• Before attaching or detaching the lens, check that the

digital camera is turned off.

• Before attaching the lens to the digital

camera, remove the lens rear cap by

rotating it in the direction of the arrow.

• To prevent dust and other particles

from accumulating on or entering the

lens, be sure to attach the lens cap/

lens rear cap after detaching the lens

from the digital camera.

∫Attaching Filters

• Vignetting may occur if using 2 or more filters at the same

time.

• It is possible to attach the lens cap with the filter already

attached.

• When using the lens hood and a filter at the same time,

attach the filter first.

• You cannot attach a conversion lens or adaptor to this

lens. A filter may be used, but attaching any other element

may cause damage to the lens.

Using the Lens Hoods

∫Attaching the Lens Hood (Supplied

Accessory)

1Align the mark A ( ) on the lens hood with

the mark on the tip of the lens.

2Rotate the lens hood in the direction of the

arrow until it clicks and then align the mark B

( ) on the lens hood with the mark on the

tip of the lens.

SQT1299_E.book 6 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

∫Temporarily Storing the Lens Hood

1Rotate the lens hood C in

the direction of the arrow

and then remove.

2Align the mark B ( ) on the lens hood with

the mark on the tip of the lens.

3Rotate the lens hood in the direction of the

arrow until it clicks into place.

Note

• If you use a lens hood and the flash at the same time, the

lens hood will block the light from the flash, causing the lower

portion of the screen to darken (vignetting) and making it

impossible to adjust the amount of light. We recommend not

using the lens hoods and flash at the same time.

SQT1299_E.book 7 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

Cautions for Use

Take care not to drop or knock the lens. Also take care

not to put a lot of pressure on the lens.

• Take care not to drop the bag that you inserted the lens in

as it may strongly shock the lens. The camera may stop

operating normally and pictures may no longer be

recorded. Also, the lens may be damaged.

• When carrying the digital camera with the lens attached,

hold both the digital camera and the lens.

When using pesticides and other volatile substances around

the camera make sure that they do not get onto the lens.

• If such substances get onto the lens they can damage the

exterior case or cause the paint to peel.

Do not point the lens at the sun or other strong light

sources.

• This could cause the lens to collect an excessive amount

of light, resulting in fire and malfunction.

• Under no circumstances should the unit be stored in any

of the following locations since doing so may cause

problems in operation or malfunctioning.

– In direct sunlight or on a beach in summer

– In locations with high temperatures and humidity levels or

where the changes in temperature and humidity are acute

– In locations with high concentrations of sand, dust or dirt

– Where there is fire

– Near heaters, air conditioners or humidifiers

– Where water may make the unit wet

– Where there is vibration

– Inside a vehicle

• Refer also to the operating instructions of the digital

camera.

• When the unit is not going to be used for a prolonged

period, we recommend storing with a desiccant (silica gel).

Failure to do so may result in performance failure caused

by mold, etc. It is recommended that you check the unit’s

operation prior to use.

• Do not leave the lens in contact with rubber or plastic

products for extended periods of time.

• Do not touch the lens contact point. Doing so can cause

failure of the unit.

• Do not disassemble or alter the unit.

Do not use benzine, thinner, alcohol or other similar

cleaning agents to clean the lens glass or exterior

cabinet.

• Using solvents can damage the lens or cause the paint to peel.

• Wipe off any dust or fingerprints with a soft, dry cloth.

• If dust or dirt accumulates on the lens mount rubber, focus

ring, or aperture ring, wipe it off with a dry dust-free cloth.

• Do not use a household detergent or a chemically treated

cloth.

A sound is heard when the camera is turned on or off.

When I take pictures of a bright subject, such as a

subject outside, or when I take pictures with a large

aperture value, the lens makes a sound.

• This is the sound of lens or aperture movement and is not

a malfunction.

Troubleshooting

SQT1299_E.book 8 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

Specifications

Specifications are subject to change without notice.

INTERCHANGEABLE LENS FOR DIGITAL CAMERA

“LEICA DG SUMMILUX 12 mm/F1.4 ASPH.”

Focal length f=12 mm

(35 mm film camera equivalent: 24 mm)

Aperture type 9 diaphragm blades/circular aperture diaphragm

Maximum aperture F1.4

Minimum aperture value F16

Lens construction 15 elements in 12 groups

(2 aspherical lenses, 1 ED lens, 2 UED lenses)

In focus distance 0.2 m (0.66 feet) to ¶ [from the focus distance reference line]

Maximum image magnification 0.1k (35 mm film camera equivalent: 0.2k)

Optical image stabilizer Not available

[AF/MF] switch Available (Switching AF/MF)

Mount “Micro Four Thirds Mount”

Angle of view 84x

Filter diameter 62 mm

Max. diameter Approx. 70.0 mm (2.8 inch)

Overall length Approx. 70.0 mm (2.8 inch)

(from the tip of the lens to the base side of the lens mount)

Mass Approx. 335 g (0.74lb)

Dust-proof and splash-proof Available

SQT1299_E.book 9 ページ２０１６年５月３０日　月曜日　午前１１時５分

SQT1299

Limited Warranty (ONLY FOR AUSTRALIA)

SQT1299_E.book 10 ページ２０１６年５月３０日　月曜日　午前１１時５分

Inhaltsverzeichnis

Sprachen:

Andere Panasonic Kameraobjektiv Handbücher

Panasonic

Panasonic Lumix H-H020A Bedienungsanleitung

Panasonic

Panasonic ET-DLE030 Bedienungsanleitung

Panasonic

Panasonic WVLZ6115 - ZOOM LENS Bedienungsanleitung

Panasonic

Panasonic WV-LA12A Bedienungsanleitung

Panasonic

Panasonic Lumix S-R24105GK Bedienungsanleitung

Panasonic

Panasonic DMW-GFC1 Bedienungsanleitung

Panasonic

Panasonic H-VSO14140 Bedienungsanleitung

Panasonic

Panasonic Lumix H-HS35100 Bedienungsanleitung

Panasonic

Panasonic ET-EMW200 Bedienungsanleitung

Panasonic

Panasonic H-RS100400 Bedienungsanleitung

Panasonic

Panasonic LUMIX S PRO Bedienungsanleitung

Panasonic

Panasonic S-R1635 Bedienungsanleitung

Panasonic

Panasonic Lumix DMC-GH2 Bedienungsanleitung

Panasonic

Panasonic WV-LZ61 Bedienungsanleitung

Panasonic

Panasonic ET-DLE060 Bedienungsanleitung

Panasonic

Panasonic Lumix H-FS014045 Bedienungsanleitung

Panasonic

Panasonic WV-LA1208 Bedienungsanleitung

Panasonic

Panasonic 5025232921027 Bedienungsanleitung

Panasonic

Panasonic H-FS35100 Bedienungsanleitung

Panasonic

Panasonic H-FS35100 Bedienungsanleitung

Panasonic

Panasonic WV-LA210C3 Bedienungsanleitung

Panasonic

Panasonic H-HS030PP Bedienungsanleitung

Panasonic

Panasonic Lumix H-F007014 Bedienungsanleitung

Panasonic

Panasonic DMW-GTC1 Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Bedienungsanleitung

Rokinon

Rokinon DS50M-C Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung