Panasonic Lumix DMC-G1KPP Bedienungsanleitung

ing and distribution is a violation of law.

ORDER NO. DSC0810042CE

B26

Digital Camera/Lens Kit

Model No.DMC-G1KPP

DMC-G1KEB

DMC-G1KEC

DMC-G1KEG

DMC-G1KGC

DMC-G1KGD

DMC-G1KGH

DMC-G1KGK

DMC-G1KGN

DMC-G1KGT

DMC-G1KGJ

Vol. 1

Colour

(K)...........Black Type

(A)...........Blue Type (except GD/GN/GT/GJ)

(R)...........Red Type (except GD/GN/GT/GJ)

TABLE OF CONTENTS PAGE PAGE

1 Safety Precaution-------------------------------------------------3

1.1. General Guidelines ----------------------------------------3

1.2. Leakage Current Cold Check---------------------------3

1.3. Leakage Current Hot Check (See Figure 1.)--------3

1.4. How to Discharge the Capacitor on Flash Sub

PCB------------------------------------------------------------4

2Warning--------------------------------------------------------------5

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------5

2.2. How to Recycle the Lithium Ion Battery (U.S.

Only)-----------------------------------------------------------5

2.3. Caution for AC Cord(For EB/GC/GH)-----------------6

2.4. How to Replace the Lithium Battery-------------------7

3 Service Navigation------------------------------------------------8

3.1. Introduction --------------------------------------------------8

3.2. Important Notice--------------------------------------------8

3.3. General Description About Lead Free Solder

(PbF) ----------------------------------------------------------9

3.4. How to Define the Model Suffix (NTSC or PAL

model)-------------------------------------------------------10

4 Specifications----------------------------------------------------13

5 Location of Controls and Components------------------14

6 Service Mode-----------------------------------------------------34

6.1. Error Code Memory Function -------------------------34

7 Troubleshooting Guide----------------------------------------36

8 Service Fixture & Tools ---------------------------------------39

8.1. Service Fixture and Tools ------------------------------39

8.2. Clean Box--------------------------------------------------40

8.3. Service Position ------------------------------------------41

9 Disassembly and Assembly Instructions---------------42

9.1. Disassembly Flow Chart--------------------------------42

9.2. PCB Location----------------------------------------------42

9.3. Disassembly Procedure --------------------------------43

9.4. Disassembly and Assemble Procedure for the

Lens ---------------------------------------------------------51

10 Measurements and Adjustments --------------------------54

10.1. Matrix Chart for Replaced Part and Necessary

Adjustment-------------------------------------------------54

11 Maintenace--------------------------------------------------------55

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment

which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essen-

tial that these critical parts should be replaced with manu-

facturer’s specified parts to prevent X-RADIATION,

shock, fire, or other hazards. Do not modify the original

design without permission of manufacturer.

2. An Isolation Transformer should always be used during

the servicing of AC Adaptor whose chassis is not isolated

from the AC power line. Use a transformer of adequate

power rating as this protects the technician from acci-

dents resulting in personal injury from electrical shocks. It

will also protect AC Adaptor from being damaged by acci-

dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been over-

heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices

such as insulation barriers, insulation papers shields are

properly installed.

5. After servicing, make the following leakage current

checks to prevent the customer from being exposed to

shock hazards.

1.2. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-

lic cabinet part on the equipment such as screwheads,

connectors, control shafts, etc. When the exposed metal-

lic part has a return path to the chassis, the reading

should be between 1 MΩand 5.2 MΩ. When the exposed

metal does not have a return path to the chassis, the

reading must be infinity.

1.3. Leakage Current Hot Check

(See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF

capacitor, between each exposed metallic part on the set

and a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 V RMS.

A leakage current tester (Simpson Model 229 or equiva-

lent) may be used to make the hot checks, leakage cur-

rent must not exceed 1/2 mA. In case a measurement is

outside of the limits specified, there is a possibility of a

shock hazard, and the equipment should be repaired and

rechecked before it is returned to the customer.

Figure. 1

1.4. How to Discharge the Capacitor on Flash Sub PCB

CAUTION:

1. Be sure to discharge the capacitor on FLASH SUB PCB.

2. Be careful of the high voltage circuit on FLASH SUB PCB when servicing.

[Discharging Procedure]

1. Refer to the disassemble procedure and Remove the necessary parts/unit.

2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1kΩ/5W).

(An equivalent type of resistor may be used.)

3. Put the resistor between both terminals of capacitor on FLASH SUB PCB for approx. 5 seconds.

4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.

Fig. F1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge

(ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-

ficient to damage an ES device).

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

2.3. Caution for AC Cord

(For EB/GC/GH)

2.3.1. Information for Your Safety

IMPORTANT

Your attention is drawn to the fact that recording of pre-

recorded tapes or discs or other published or broadcast

material may infringe copyright laws.

WARNING

To reduce the risk of fire or shock hazard, do not expose

this equipment to rain or moisture.

CAUTION

To reduce the risk of fire or shock hazard and annoying

interference, use the recommended accessories only.

FOR YOUR SAFETY

DO NOT REMOVE THE OUTER COVER

To prevent electric shock, do not remove the cover. No user

serviceable parts inside. Refer servicing to qualified service

personnel.

2.3.2. Caution for AC Mains Lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plug

for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the

replacement fuse has a rating of 5 amperes and it is approved

by ASTA or BSI to BS1362

Check for the ASTA mark or the BSI mark on the body of the

fuse.

If the plug contains a removable fuse cover you must ensure

that it is refitted when the fuse is replaced.

If you lose the fuse cover, the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your local

Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in

your home then the fuse should be removed and the plug cut

off and disposed of safety.

There is a danger of severe electrical shock if the cut off plug is

inserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code as

shown below.

If in any doubt, please consult a qualified electrician.

2.3.2.1. Important

The wires in this mains lead are coloured in accordance with

the following code:

As the colours of the wires in the mains lead of this appliance

may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the ter-

minal in the plug which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to the

terminal in the plug which is marked with the letter L or coloured

RED.

Under no circumstances should either of these wires be con-

nected to the earth terminal of the three pin plug, marked with

the letter E or the Earth Symbol.

2.3.2.2. Before Use

Remove the Connector Cover as follows.

2.3.2.3. How to Replace the Fuse

1. Remove the Fuse Cover with a screwdriver.

2. Replace the fuse and attach the Fuse cover.

Blue Neutral

Brown Live

2.4. How to Replace the Lithium Battery

2.4.1. Replacement Procedure

1. Remove the REMOTE PCB. (Refer to Disassembly Procedures.)

2. Remove the Lithium battery (Ref. No. “B7351” at component side of REMOTE PCB) and then replace it into new one.

NOTE:

This Lithium battery is a critical component.

(Type No.: ML421S/ZT Manufactured by Energy Company, Panasonic Corporation.)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in requirement designed specifically for its use.

Replacement batteries must be of same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

NOTE:

Above caution is applicable for a battery pack which is for DMC-G1K series, as well.

3 Service Navigation

3.1. Introduction

This service manual contains technical information, which allow service personnel’s to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2. Important Notice

3.2.1. Camera Body Unit

3.2.1.1. About Mount Box Block (Ref. 8)

1. This Service Manual does not contain the repair service information for "MOUNT BOX BLOCK"(Ref.8), because it requires

special facilities and equipment.

a. Schematic diagram, Block diagram and P.C.B. layout of "MOUNT BOX BLOCK".

b. Parts list for individual parts of "MOUNT BOX BLOCK"

2. If the "MOUNT BOX BLOCK" is confirmed as defective, exchange the "MOUNT BOX BLOCK" as supplied as service parts.

3. Before exchange the "MOUNT BOX BLOCK", the performances must be carefully checked ,by following the "7.Troubleshoot-

ing Guide" section of this service manual.

Fig. S1

Important:

1. After replacing the MOUNT BOX BLOCK, the mount box data has to be stored to the unit.

For more details, consult the adjustment instruction which is available together with the Maintenance software at "software

download" on the "Support Information from NWBG/VDBG-AVC" web-site in "TSN system".

2. The full adjustment procedures must be performed after replacing the "MOUNT BOX BLOCK", otherwise picture quality can

not be meet with specification.

3.2.1.2. About Main PCB (Ref. 1)

1. This Service Manual does not contain the repair service information for "MAIN P.C.B."(Ref.1), because it requires special facil-

ities and equipment.

a. Schematic diagram, Block diagram and P.C.B. layout of "MAIN P.C.B.".

b. Parts list for individual parts of "MAIN P.C.B."

2. When a part replacement is required for repairing "MAIN P.C.B.", replace as an assembled parts. (MAIN P.C.B.)

3. The following category is recycle module part. please send it/them to Central Repair Center.

*MAIN P.C.B. (VEP56071A)

4. Before exchange the "MAIN P.C.B.", the performances must be carefully checked ,by following the "7.Troubleshooting Guide"

section of this service manual.

Important:

1. Before replacing the "MAIN P.C.B.", proceed the EEPROM data backup from the unit. After replacing the MAIN PCB, over-

write the EEPROM data with backup data from the unit. before proceeding the adjustment /inspection.

For more details, consult the adjustment instruction which is available together with the Maintenance software at "software

download" on the "Support Information from NWBG/VDBG-AVC" web-site in "TSN system".

2. The full adjustment procedures must be performed After replacing the "MAIN P.C.B.", otherwise Picture quality can not be

meet with specification.

3.2.2. Lens Unit

1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.208), because it

requires special facilities and equipment.

2. "LENS MAIN BLOCK UNIT" performance must be confirmed with the "7.Troubleshooting Guide" section of this service man-

ual.

3. In case of the "LENS MAIN BLOCK UNIT" defect, contact to the service department of sales company.

Fig. S2

3.3. General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this

equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin

(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the

normal solder.

Distinction of PCB Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.

• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C

(662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01K-----------(0.3mm 100g Reel)

RFKZ06D01K-----------(0.6mm 100g Reel)

RFKZ10D01K-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

3.4. How to Define the Model Suffix (NTSC or PAL model)

There are seven kinds of DMC-G1K, regardless of the colours.

• a) DMC-G1K (Japan domestic model)

• b) DMC-G1KPP

• c) DMC-G1KEB/EC/EG/GH

• d) DMC-G1KGC/GJ/GN

• e) DMC-G1KGD

• f) DMC-G1KGT

• g) DMC-G1KGK

What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash ROM mounted on MAIN PCB.

3.4.1. Defining methods:

To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Kameraobjektiv Handbücher

Panasonic

Panasonic ET-DLE170 Bedienungsanleitung

Panasonic

Panasonic LUMIX H-F007014E Bedienungsanleitung

Panasonic

Panasonic WV-LA12A Bedienungsanleitung

Panasonic

Panasonic WV-LZ6 Bedienungsanleitung

Panasonic

Panasonic Lumix H-F008 Bedienungsanleitung

Panasonic

Panasonic WV-LA36 Bedienungsanleitung

Panasonic

Panasonic Lumix S-E70200GK Bedienungsanleitung

Panasonic

Panasonic H-FS12032K Bedienungsanleitung

Panasonic

Panasonic H-RS100400 Bedienungsanleitung

Panasonic

Panasonic WV-LXY18C4 Bedienungsanleitung

Panasonic

Panasonic H-HSA12035PP Bedienungsanleitung

Panasonic

Panasonic Lumix DMW-STC14 Bedienungsanleitung

Panasonic

Panasonic ET-ELW22 Bedienungsanleitung

Panasonic

Panasonic H-FS35100PP Bedienungsanleitung

Panasonic

Panasonic Lumix H-X015E-K Bedienungsanleitung

Panasonic

Panasonic WV-LZA61/2 Bedienungsanleitung

Panasonic

Panasonic H-FS1442APP Bedienungsanleitung

Panasonic

Panasonic WV-LM6B2 Bedienungsanleitung

Panasonic

Panasonic ET-D75LE30 Bedienungsanleitung

Panasonic

Panasonic H-X2550 Bedienungsanleitung

Panasonic

Panasonic ET-D3LEF70C Bedienungsanleitung

Panasonic

Panasonic WV-LFY3C3 Bedienungsanleitung

Panasonic

Panasonic WV-LZA61/2S Bedienungsanleitung

Panasonic

Panasonic LUMIX S PRO R1635 Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Bedienungsanleitung

Rokinon

Rokinon DS50M-C Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung