Panasonic EB-GD30 Kurzanleitung

Order Number: MCUK991001G8

Issue 1

Revision 0

Technical Guide

GD30/GD50 Personal Cellular Telephone

Handheld Portable

EB-GD30

EB-GD50

Specification

Battery life figures are dependent on network conditions.

900 MHz 1800 MHz

Frequency range Tx: 890 - 915 MHz

Rx: 935 - 960 MHz

Tx: 1710 - 1785 MHz

Rx: 1805 - 1880 MHz

Tx/Rx frequency separation 45 MHz 95 MHz

RF channel bandwidth 200 kHz

Number of RF channels 124 374

Speech coding Full rate/Half rate/Enhanced

Full rate

Full rate/Half rate

Operating temperature -10°C to +55°C

Type Class 4 Handheld Class 1 Handheld

RF Output Power 2 W maximum 1 W maximum

Modulation GMSK (BT = 0.3)

Connection 8 ch/TDMA

Voice digitizing 13 kbps RPE-LTP / 13 kps ACLEP / 5.6 kps CELP / VSLEP

Transmission speed 270.3 kbps

Diversity Frequency hopping

Signal Reception Double superheterodyne

Intermediate Frequencies 282 MHz and 45 MHz

Antenna Terminal Impedance 50 Ω

Antenna VSWR <2.1 : 1

Dimensions Height: 135 mm

Width: 45 mm

Depth: 20.5 mm (30 mm with EB-BLD30 Battery)

Volume 123 cc (150 cc with EB-BLD30 Battery)

Weight GD30: 130 g with EB-BSD30 Battery (170 g with EB-BLD30)

GD50: 115 g with EB-BSD50 Battery (170 g with EB-BLD30)

Display Graphical chip on glass liquid crystal, Alphanumeric,

16 x 3 characters, 5 icons and 6 x 1 characters

Illumination 4 LEDs for the LCD (Green)

8 LEDs for the keypad (Green)

1 LED Incoming call (Green)

1 Charging LED (Red)

Keypad 17 keys, Navigation key

SIM Plug-in type only

External DC Supply Voltage 3.6 V

Battery EB-BSD30: 3.6 V nominal, 670mAh, Ni-MH

EB-BSD50: 3.6 V nominal, 670mAh, Li-Ion

EB-BLD30: 3.6 V nominal, 1340mAh, Ni-MH

Standby Battery Life

DRX 9

EB-BSD30/EB-BSD50: 95 hrs maximum

EB-BLD30: 190 hrs maximum

Conversation Battery Life

PL 7, DTX 50%

EB-BSD30/EB-BSD50: 180 minutes

EB-BLD30: 360 minutes

WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or

cautions to advise non-technical individuals of potential dangers in attempting to service a product.

Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or

products dealt with in this service manual by anyone else could result in serious injury or death.

Issue 1 – ii – MCUK991001G8

Revision 0 Technical Guide

This Technical Guide is copyright and issued on the strict understanding that it is not to be reproduced, copied, or disclosed to

any third party, either in whole or part, without the prior written consent of Matsushita Communication Industrial UK Ltd.

Every care has been taken to ensure that the contents of this manual give an accurate representation of the equipment.

However, Matsushita Communication Industrial UK Ltd. accepts no responsibility for inaccuracies which may occur and

reserves the right to make changes to specification or design without prior notice.

The information contained in this manual and all rights in any designs disclosed therein, are and remain the exclusive property

of Matsushita Communication Industrial UK Ltd.

Other patents applying to material contained in this publication:

BULL CP8 PATENTS

Comments or correspondence concerning this manual should be addressed to:

Customer Support Department,

Matsushita Communication Industrial UK Ltd.,

Colthrop,Thatcham,

Berkshire. RG19 4ZD.

ENGLAND

MCUK991001G8 Section Issue 1

Technical Guide – iii – Revision 0

CONTENTS

1 INTRODUCTION

1.1 Purpose of this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Structure of the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 INTERFACES AND TEST POINTS

2.1 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 RF OVERVIEW

3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.3 RF & Accessory Connector . . . . . . . . . . . . . . . . . . . . . . 12

4 TRANSMITTER

4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Uplink Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 RECEIVER

5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.2 Downlink Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . 16

6 BASEBAND OVERVIEW

6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6.2 Functional Description of the PCB . . . . . . . . . . . . . . . . 19

7 GEMINI

7.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

7.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . 27

8 VEGA

8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

8.2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . 31

9 POWER SUPPLIES

9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

9.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

9.3 Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

9.4 Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

9.5 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Issue 1 Section MCUK991001G8

Revision 0 – iv – Technical Guide

This page is left intentionally blank.

INTRODUCTION

MCUK991001G8 Section 1 Issue 1

Technical Guide – 1 – Revision 0

1 INTRODUCTION

1.1 Purpose of this Guide

This guide contains technical information for the Panasonic GD30 personal cellular telephone system operating on the GSM

network. Procedures for installing, operating and servicing (e.g. disassembly and testing) the telephone system are provided

in the associated Service Manual.

1.2 Structure of the Guide

The guide is structured to provide service-engineering personnel with the following technical information on the GSM mobile

telephone:

1. Interface details and relevant test points.

2. Functional description of each section of the mobile telephone.

3. Detailed description of each section of the mobile telephone.

INTRODUCTION

Issue 1 Section 1 MCUK991001G8

Revision 0 – 2 – Technical Guide

This page is left intentionally blank.

INTERFACES AND TEST POINTS

MCUK991001G8 Section 2 Issue 1

Technical Guide – 3 – Revision 0

2 INTERFACES AND TEST POINTS

2.1 Interfaces

2.1.1 Main and Keypad PCBs

The interface between Main and Keypad PCBs is made via a 32-way connector as follows:

Figure 2.1: GD30/GD50 Interboard Connector

No. Signal Name MAIN <=> KEYPAD Function Connection

1 2V8 - Power Source for LCD Module

2 DATA(7) <==> MPU Data bus (7)

3 DATA(6) <==> MPU Data bus (6)

4 DATA(1) <==> MPU Data bus (1)

5 DATA(2) <==> MPU Data bus (2)

6 DATA(4) <==> MPU Data bus (4)

7 DATA(0) <==> MPU Data bus (0)

8 DATA(5) <==> MPU Data bus (5)

9 DATA(3) <==> MPU Data bus (3)

10 GROUND -

11 PGLEDOUT ==> Paging LED control signal SIM_PWR IC pin 22

12 RnW ==> MPU Read/nWrite signal GEMINI pin 20

13 CS_LCD ==> LCD chip select signal GEMINI pin 55

14 nRESET ==> MPU nRESET signal

15 KBC(0) ==> Key Column 0 signal for Key scan GEMINI pin 132

16 KBC(1) ==> Key Column 1signal for Key scan GEMINI pin 133

17 KBC(2) ==> Key Column 2 signal for Key scan GEMINI pin 130

18 KBC(3) ==> Key Column 3 signal for Key scan GEMINI pin 129

19 KBC(4) ==> Key Column 4 signal for Key scan GEMINI pin 128

20 KBR(0) <== Key Row 0 signal for Key scan GEMINI pin 126

21 KBR(1) <== Key Row 1 signal for Key scan GEMINI pin 125

22 KBR(2) <== Key Row 2 signal for Key scan GEMINI pin 124

23 KBR(3) <== Key Row 3 signal for Key scan GEMINI pin 123

24 KBR(4) <== Key Row 4 signal for Key scan GEMINI pin 122

25 nPOWKEY <== Power Key sense signal

26 GROUND -

27 CHLEDOUT ==> Charge LED control signal GEMINI pin 105

28 2V8 - Power Source for LCD Module

29 ADDRESS(1) ==> MPU Address bus (1) GEMINI pin 25

30 BKLTOUT ==> Key Backlight Power Source Charge IC pin 16

31 EAR_N ==> Receiver Negative Output

32 EAR_P ==> Receiver Positive Output

10160-1

KBR(3)DATA(0) 7 23

GROUNDGROUND 10 26

KBC(2)2V8 1 17 KBC(3)DATA(7) 2 18 KBC(4)DATA(6) 3 19 KBR(0)DATA(1) 4 20 KBR(1)DATA(2) 5 21 KBR(2)DATA(4) 6 22

KBR(4)DATA(5) 8 24 nPOWKEYDATA(3) 9 25

CHLEDOUTPGLEDOUT 11 27 2V8RnW 12 28 ADD(1)CS_LCD 13 29 BKLTOUTnRESET 14 30 EAR_NKBC(0) 15 31 EAR_PKBC(1) 16 32

P100

INTERFACES AND TEST POINTS

Issue 1 Section 2 MCUK991001G8

Revision 0 – 4 – Technical Guide

2.1.2 External Interface

The GD30 and GD50 telephones have two external connectors:

1. a multi-way connector for use with external accessories such as hands free kits and PC data card.

2. additional contacts for charging the battery pack while inserted in the desktop charger.

Main Unit <==> External I/O

No. Name H/H <=> EXT Total Function H/H Circuit

1 GND ==> 6 Ground

2 PA_ON ==> 1 Gating of spectrum analyser for Transmitter

performance testing

L: Off, Hi - Z: On)

3 nLOGIC_PWR ==> 1 Accessory Power Control signal.

In the handsfree this is logical OR’ed with

IGNITION in order that the software can

maintain the Handsfree power-on state if the

user is in a call and that the IGNITION is

switched off. L: Power-on, Hi-Z: Power-off

4 IGNITION <== 1 IGNITION is used in two cases.

1) Determine the mode of operation of the H/H

when the Handsfree accessory is attached.

L: At a suitable time enter dummy sleep mode

and therefore minimise the drain on the car

battery (nLOGIC_POWER = Hi - Z)

H: Normal mode

2) Satisfy 2nd of 2 conditions for sending

initialise Testset command and entering Testset

mode. (see nADP_SENSE for 1st condition)

L: Condition 2 satisfied

H: Enter Testset mode not satisfied

5 VBAT <=> 1 The pin is either an input or an output

depending upon the battery connection.

1) Battery/Dummy battery connected: Output

supply terminal for attached accessories.

2) No connection: Low current input supply

terminal for non-RF performance checking in

Testset Mode or Flash programming.

6 nH/F_SENSE <== 1 Handsfree sense line

L: connected

H (internal pull-up): disconnected

7 nRADIO_MUTE ==> 1 Radio Mute

L: mute, Hi-Z: unmute)

8 RX_AUDIO ==> 1 Accessory Receiving Audio

-16 dBm0 = 76.7m Vrms

9 GND ==> Ground Refer to pin 1

10 EXT-PWR <== 2 Power supply for battery charging, Power ON/

Off control and accessory control circuits.

Voltage: 5.8 ± 0.2 V

Current: 650 ± 50 mA

10095-1

10k

330p

10096-1

330

10097-1

330

50k

200

10098-1

10099-1

330

100k

10100-1

330

50k

200

10101-1

560

10102-1

10103-1

Trickle Charge Circuit

Power On/Off Control Circuit

Rapid Charge Circuit

Accessory Control Circuit

INTERFACES AND TEST POINTS

MCUK991001G8 Section 2 Issue 1

Technical Guide – 5 – Revision 0

11 NON_HOOK <== 1 Indicates if the optional second handset is on or

off hook. In handsfree operation, if the optional

handset is not fitted this signal defaults to on

hook. (Low.)

12 SERIAL_OUT ==> 1 Downlink Serial Data

(Baud rate is same as SERIAL_IN)

13 SERIAL_IN <== 1 Uplink Serial Data

The baud rate is dependant upon the attached

accessory, whether operating in Testset Mode

or Flash Downloading.

SMS cable: 9600 bps

RS232 Direct cable: 38.4 kbps

Data adapter: 33.8 kbps

Testset: 9600 bps

Flash Download: 56 kbps

14 nADP_SENSE <== 1 NADP_SENSE has 5 possible states. The state

is determined by the value of the pull-down

resistor in the attached accessory / test set.

NADP_SENSE has 2 purposes as follows:

1) To identify an attached accessory.

Open (H): No attached accessory

82 kΩ=± 1% (MH): Headset Adapter

56 kΩ=± 1% (M): SMS Cable

33 kΩ=± 1% (ML): RS232C Direct Cable

GND (L): Data Adapter

2) Determine whether the 1st of 2 conditions

are satisfied for sending the initialise Testset

command on SERIAL_OUT, and entering

Testset mode (see IGNITION for 2nd condition).

H/MH: Condition 1 satisfied

M/ML/L: Enter Testset Mode not satisfied

15 NH/F_ON ==> 1 Accessory Sending & Receiving Audio paths

unmute

L: unmute, Hi-Z: mute

16 GND ==> 6 Refer to pin 1 Refer to pin 1

17 TX_AUDIO <== 1 Accessory Sending Audio

-16 dBm0 = 40.4 m Vrms

18 GND ==> 6 Ground connection of Dual Charger Refer to pin 1

19 GND ==> 6 Ground connection of Dual Charger Refer to pin 1

20 GND ==> 6 Ground connection of Dual Charger Refer to pin 1

21 GND ==> 6 Ground connection of Dual Charger Refer to pin 1

22 CHARGE_ON <=> 1 The Dual Charger shall hold CHARGE_ON to

the middle level until a H/H is inserted into the

front slot.

H: 2.0<=V<=3.0 volts; Dual Charger detects

connection of H/H

M: 1.0<=V<2.0 volts; Unconnected

L: 0.0<=V<1.0 volts; Dual Charger detects

connection of H/H

23 EXT_PWR <== 2 The Dual Charger shall control switching of the

power supply to the front slot (corresponds to

EXT_PWR) based on the state of the

CHARGE_ON signal.

H: EXT_PWR supplied

L: When the H/H can determine whether or not

to set CHARGE_ON. After the insertion of the

H/H, EXT_PWR shall be subsequently supplied

withinTBA hours

Refer to pin 8

No. Name H/H <=> EXT Total Function H/H Circuit

330

100k

10100-1

330

2.2k

47k

10104-1

330

4.7 k

10105-1

330

100k

10100-1

330

50k

200

10101-1

11 10k

3k3

10106-1

10k

330

CHARGE_ON

0.1µ

10107-1

INTERFACES AND TEST POINTS

Issue 1 Section 2 MCUK991001G8

Revision 0 – 6 – Technical Guide

Battery Connector

SIM Interface

No. Name H/H <=> EXT Total Function H/H Circuit

1 VBAT <== 1 Positive battery terminal.

Li+ (2 cells in parallel): 3.6 V nom.

NiMH (3 cells in series): 3.6 V nom.

2 BAT_TEMP <== 1 BAT_TEMP has 2 purposes.

1) Determine whether a battery is attached to

the H/H.

2) Monitor battery temperature for the purposes

of charging.

H: Abnormal battery

M: Li+ or NiMH charging

L: No battery or abnormal battery

3 GND <== 1 Negative battery terminal

4 BAT_ID <== 1 BAT_ID is used to identify the type of attached

battery.

H: Li+ or no battery connected.

L: NiMH

Pin Signal

1GND

25V

3 Not connected

4 Reset

5 Serial input/output

6 Clock

7 Not connected

8 Not connected

10108-1

ChargerIC VREFOUT

ESD

Vega_ADIN2

ESD

Protection

10109-1

10110-1

Andere Handbücher für EB-GD30

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Handy Handbücher

Panasonic

Panasonic KX-TU327 E Bedienungsanleitung

Panasonic

Panasonic EB-X100 Bedienungsanleitung

Panasonic

Panasonic EB-X700 Bedienungsanleitung

Panasonic

Panasonic EB-GD87 Bedienungsanleitung

Panasonic

Panasonic WX-CT2020 Bedienungsanleitung

Panasonic

Panasonic EB-G600 Bedienungsanleitung

Panasonic

Panasonic P342i Bedienungsanleitung

Panasonic

Panasonic G600 Kurzanleitung

Panasonic

Panasonic EB-G50 Bedienungsanleitung

Panasonic

Panasonic X70 Bedienungsanleitung

Panasonic

Panasonic EB-GD52 Bedienungsanleitung

Panasonic

Panasonic X300 Bedienungsanleitung

Panasonic

Panasonic EBGU87 - CELLPHONE W/DIGITAL CAM Bedienungsanleitung

Panasonic

Panasonic EB-X300 Bedienungsanleitung

Panasonic

Panasonic EB-G51M Bedienungsanleitung

Panasonic

Panasonic P342i Bedienungsanleitung

Panasonic

Panasonic WX-CC2010 Series Bedienungsanleitung

Panasonic

Panasonic EB-GD67 Bedienungsanleitung

Panasonic

Panasonic A102 Bedienungsanleitung

Panasonic

Panasonic EBX70 - CELL PHONE Bedienungsanleitung

Panasonic

Panasonic A500 Bedienungsanleitung

Panasonic

Panasonic GD55 Bedienungsanleitung

Panasonic

Panasonic EB-H63 Series Bedienungsanleitung

Panasonic

Panasonic EB-H70 Series Bedienungsanleitung

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung