Panasonic KX-TDA6181X Bedienungsanleitung
© 2005 Panasonic Communications Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
KX-TDA6181X
(for Asia, Oceania, Middle Near East, Latin America,
Russia and Africa)
16-Port Analogue Trunk Card
IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF, Standard laded, (Pb),
solder can be used as usual on boards without the PbF mark.
When this mark does appear please read and follow the special instructions described in this manual on the use of PbF and how
it might be permissible to use Pb solder during service and repair work.
ORDER NO. KMS0510155CE
1 ABOUT LEAD FREE SOLDER (PbF: Pb free) 3
1.1. SUGGESTED PBF SOLDER 3
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS
USED 4
2 FOR SERVICE TECHNICIANS 5
3 GENERAL DESCRIPTION 5
4 SPECIFICATION 5
5 SYSTEM CONSTRUCTION 6
5.1. INSTALLING/REMOVING THE OPTIONAL SERVICE
CARDS 7
6 BLOCK DIAGRAM 14
7 CIRCUIT OPERATIONS 15
7.1. CONTROL-SYSTEM CIRCUIT 15
7.2. DESCRIPTION OF FUNCTIONS AND CIRCUITS 19
7.3. POWER SUPPLY CIRCUIT 22
8 TROUBLESHOOTING GUIDE 24
9 IC DATA 30
9.1. IC3 (ASIC) 30
9.2. IC6 (CODEC) 32
9.3. IC7 (CODEC) 33
9.4. IC9 (CODEC) 34
9.5. IC10 (CODEC) 35
9.6. IC601 (CPU) I/O MAP 36
10 HOW TO REPLACE A FLAT PACKAGE IC 37
10.1. PREPARATION 37
10.2. REMOVAL PROCEDURE 37
10.3. INSTALLATION PROCEDURE 37
10.4. REMOVING SOLDER FROM BETWEEN PINS 37
11 TERMINAL GUIDE OF ICs, TRANSISTORS AND DIODES 38
12 CABINET AND ELECTRICAL PARTS LOCATION 39
13 ACCESSORIES AND PACKING MATERIAL 40
14 REPLACEMENT PARTS LIST 41
14.1. CABINET AND ELECTRICAL PARTS LOCATION 41
14.2. ACCESSORIES AND PACKING MATERIALS 41
14.3. MAIN BOARD PARTS 41
15 FOR SCHEMATIC DIAGRAM 51
15.1. WAVEFORM 52
15.2. ELCOT16 BLOCK DIAGRAM 55
16 SCHEMATIC DIAGRAM 56
16.1. No.1 56
16.2. No.2 60
16.3. No.3 64
16.4. No.4 68
17 PRINTED CIRCUIT BOARD 70
17.1. COMPONENT VIEW 70
17.2. BOTTOM VIEW 71
CONTENTS
Page Page
2
KX-TDA6181X
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)
Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that
contains lead.
We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
Caution
•
• •
• PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with
temperature control and adjust it to 700° ± 20° F, (370° ± 10°C). In case of using high temperature soldering iron, please
be careful not to heat too long.
•
• •
• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (600°C).
•
• •
• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible
and be sure that any remaining is melted prior to applying the Pb solder.
•
• •
• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See figure, below).
1.1. SUGGESTED PBF SOLDER
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the
manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
3
KX-TDA6181X
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED
4
KX-TDA6181X
2 FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover the plastic part´s boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the worktable.
4. Do not touch the IC or LSI pins with bare fingers.
3 GENERAL DESCRIPTION
This card is inserted in the free slot of the TDA600 system and is capable of connecting 16 analog loop start lines.
Up to 2 CALLER ID/PAYTONE card can be added on as option cards.
The LPR is an SH-1 (SH7020) with 512Kbyte flash ROM and 128Kbyte SRAM, and supports software version upgrade though
downloading.
4 SPECIFICATION
Functional Block Functional contents
Analog External Line Interface Number of Ports 16 ports
Main Function +30V 30mA Feeding function
Dial Pulse Signal Transmission Function
DTMF Signal Transmission Function
Inversion Detection Function
Bell Detecting Function
Ring-off Signal Detection Function
2w/4w Conversion Function
Surge Protection Function
Returning Sound Generation Function
4ch CODEC Function
•
• •
• CODEC function
•
• •
• Power down function
•
• •
• µ/A Iaw switching function
•
• •
• Test function (Loop back, Tone generation)
•
• •
• Programmable digital filtering function
•
• •
• Serial interface function
•
• •
• PIO function
DTMF Generator Transmits arbitrary tones for every 16 line port
Option Card Can be installed two CO-CID/PT cards for eight lines
On-board DC/DC Power Supply Input +15V
Output +15V, +5V, +3.3V
Power Failure Forwarding Function Supports four lines
Self-diagnosis Function Performed with the extension interface in pairs
Channel Test, Dial Pulse Test, DTMF Test
ASIC#2 (eSAMSON) EC Bus interface function
H.100 Bus interface function, Digital PLL function
Local Bus interface function
Time Switch Function, Gain Control Function
Intelligent PIO Function, JTAG
Control Unit CPU SH-1/SH7020 (12.288MHz)
Flash ROM 512Kbyte
SRAM 128Kbyte
LED Display Circuit Card Status Display LED: 2-color (red/green)
External Interface Connector External Line Interface 50pin Amphenol Connector: 1 unit
Power Failure Transfer 4pin Modular Jack: 2 units
5
KX-TDA6181X
5 SYSTEM CONSTRUCTION
6
KX-TDA6181X
5.1. INSTALLING/REMOVING THE OPTIONAL SERVICE CARDS
Slot Condition
Card Type Slot Type
KX-TDA600 KX-TDA620
Free 1-10 EMPR BUS-M Free 1-11 BUS-S
EMPR Card No Yes No No No
BUS-M Card No No Yes No No
BUS-S Card No No No No Yes
Trunk Cards Yes No No Yes No
Extension Cards Yes No No Yes No
OPB3 Card Yes No No Yes No
CTI-LINK Card Yes No No No No
EECHO Card Yes No No Yes No
Caution:
To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional
service cards.To discharge static, touch ground or wear an earthing strap.
ELCOT16 Card
Function
16-port analogue trunk card with 4 power failure transfer (PFT) ports.
Accessories and User-supplied Items
Accessories (included): Screws X 2
User-supplied (not included): Amphenol connector
7
KX-TDA6181X
Pin Assignments
Amphenol Connector
No. Signal Name Function No. Signal Name Function
1 RA Ring port 1 26 TA Tip port 1
2 RB Ring port 2 27 TB Tip port 2
3 RC Ring port 3 28 TC Tip port 3
4 RD Ring port 4 29 TD Tip port 4
5 RE Ring port 5 30 TE Tip port 5
6 RF Ring port 6 31 TF Tip port 6
7 RG Ring port 7 32 TG Tip port 7
8 RH Ring port 8 33 TH Tip port 8
9 RI Ring port 9 34 TI Tip port 9
10 RJ Ring port 10 35 TJ Tip port 10
11 RK Ring port 11 36 TK Tip port 11
12 RL Ring port 12 37 TL Tip port 12
13 RM Ring port 13 38 TM Tip port 13
14 RN Ring port 14 39 TN Tip port 14
15 RO Ring port 15 40 TO Tip port 15
16 RP Ring port 16 41 TP Tip port 16
17-
25
Reserved - 42-
50
Reserved -
LED Indications
Indication Color Description
CARD STATUS Green/Red Card status indication
OFF: Power Off
Green ON: Normal (all ports are idle)
Green Flash (60 times per minute ): Normal (a port is in use)
Red ON: Fault (includes reset)
Red Flash (60 times per minute): Out of Service
8
KX-TDA6181X
In case of install CID/PAY8 on ELCOT16 card
Function
CID/PAY8: 8-port Caller ID signal type FSK/FSK (with Visual Caller ID)/DTMF, and 8 ports of Pay Tone Service (12
kHz/16kHz).To be mounted on the ELCOT16 cards.
CID8: 8-port Caller ID signal type FSK/FSK (with Visual Caller ID)/DTMF, To be mounted on the ELCOT16 cards.
Accessories and User-supplied Items
Accessories (included): Screws X 2
User-supplied (not included): none
Switch Settings (In case of install CID/PAY8 on ELCOT16 card)
Switch Type Usage and Status Definition
Port Setting DIP Set all DIP switch at “OFF” positions.
9
KX-TDA6181X
Fastening Amphenol Type Connector
An amphenol 57JE type connector is used on some of the optional sevice cards.
To connect an amphenol connector, use the spring latch or screw to fix the upper part and use Velcro tape to fix the lower
part of the connector.
10
KX-TDA6181X
Inhaltsverzeichnis
Andere Panasonic Computerhardware Handbücher
Panasonic
Panasonic TY-FB7HD Bedienungsanleitung
Panasonic
Panasonic 2SC4627G Bedienungsanleitung
Panasonic
Panasonic Ramsa WU-SX05 Bedienungsanleitung
Panasonic
Panasonic KXF-9R4C Bedienungsanleitung
Panasonic
Panasonic TY-SB01F Bedienungsanleitung
Panasonic
Panasonic 2SA2162 Bedienungsanleitung
Panasonic
Panasonic AJ-YA931G Bedienungsanleitung
Panasonic
Panasonic KX-TVP120C Bedienungsanleitung
Panasonic
Panasonic WJ-MPU850 Bedienungsanleitung
Panasonic
Panasonic ET-MDNFB10 Bedienungsanleitung
Panasonic
Panasonic TY-42TM6B - Monitor Terminal Expansion Board Benutzerhandbuch
Panasonic
Panasonic MN101L Series Bedienungsanleitung
Panasonic
Panasonic 2SC3312 Bedienungsanleitung
Panasonic
Panasonic PAW-FC Handbuch
Panasonic
Panasonic TY-FB10HMD - Monitor Terminal Expansion... Bedienungsanleitung
Panasonic
Panasonic 2SC2295 Bedienungsanleitung
Panasonic
Panasonic TY-42TM6D - Monitor Terminal Expansion Board Bedienungsanleitung
Panasonic
Panasonic ET-MDNHM10C Bedienungsanleitung
Panasonic
Panasonic UP05C8PG Bedienungsanleitung
Panasonic
Panasonic 2SB1321A Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
Hauppauge
Hauppauge WinTV-HVR-2250 Bedienungsanleitung
