Panasonic FP-XH M8N16PD Bedienungsanleitung

SAFETY PRECAUTIONS

To prevent accidents or personal injuries, please be sure to comply with the following items.

Prior to installation, operation, maintenance and check, please read this manual carefully for proper use.

Before using, please fully understand the knowledge related to the equipment, safety precautions and all

other precautions.

Safety precautions are divided into two levels in this manual: Warning and Caution.

WARNING

Incorrect operation may lead to death or serious injury.

●Take appropriate safety measures to the external circuit of the product to ensure the security of

the whole system in case of abnormalities caused by product failure or external.

●Do not use this product in areas with inflammable gases.

Otherwise it may lead to an explosion.

●Do not put this product into a fire.

Otherwise it could cause damage to the battery or other electronic parts.

●Do not impact, charge or heat the lithium battery, and do not put it into a fire.

Otherwise it may lead to fire or damage.

CAUTION

Incorrect operation may lead to injury or material loss.

●To prevent the excessive exothermic heat or smoke generation of the product, a certain margin is

required for guaranteed characteristics and performance ratings of relative products.

●Do not decompose or transform it.

Otherwise it will lead to the excessive exothermic heat or smoke generation of the product.

●Do not touch terminal blocks during power-on.

Otherwise it may result in an electric shock.

●Set an emergency stop and interlock circuit in the external devices.

●Connect wires and connectors reliably.

Otherwise it may lead to the excessive exothermic heat or smoke generation of the product.

●Ground the protective earth (PE) terminal with Class D grounding (grounding resistance at 100Ωor below).

Otherwise it may result in an electric shock.

●There shall be no foreign matters such as liquids, flammable materials and metals inside the product.

Otherwise it will lead to the excessive exothermic heat or smoke generation of the product.

●Do not carry out construction (wiring, removal, etc.) during power-on.

Otherwise it may result in an electric shock.

Description on Copyright and Trademarks

●The copyright of this manual is owned by Panasonic Industrial Devices SUNX Co., Ltd.

●Unauthorized reproduction of this manual is strictly prohibited.

●Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.

●Ethernet is a registered trademark of Fuji Xerox Co., Ltd. and Xerox Corporation.

●Other company and product names are trademarks or registered trademarks of their respective companies.

PLC_BATPE_ET

Introduction

Thank you for buying a Panasonic product. Before you use the product, please carefully read

the installation instructions and the user’s manual, and understand their contents in detail to

use the product properly.

Type of Manual

There are different types of users manual for the FP-XH M8N16PD series, as listed below.

Please refer to a relevant manual for the unit and purpose of your use.

The manuals can be downloaded on our website:

http://industrial.panasonic.com/ac/e/dl_center/manual/

Unit name or purpose of

use Manual name Manual code

FP-XH M8N16PD

Control Unit

FP-XH M8N16PD

Control Unit User’s Manual WUME-FPXHM8N16PD

FP Series Instruction Manual ARCT1F313E

Communication Function

FP-XH User Manual (Communication Section) WUME-FPXHCOM

FP-X Expansion

(Communication) Cassette

FP-X Expansion Unit FP-X Series User Manual ARCT1F409E

FP-X Function Cassette

Control Unit Version

The version of the control unit can be confirmed according to the nameplate on the side of the

product body or on the menu of the tool software.

Marking of the product body

2 CPU versions are marked on the nameplate on the side of the product body.

Ver.1.00 / Ver.1.00

① ②

Description

①The "Main CPU" version for overall operation is marked.

②The "Motion CPU" version for motion control is marked.

Table of Contents

iii

Confirmation based on the tool software

The version of the Main CPU can be confirmed according to Status Display of FPWIN GR7.

The version of Motion CPU can be confirmed via the Status Display dialog box of Configurator

PM7. The dialog box displays the "firmware version".

Contents

Glossary

As for the following terms, similar expressions are used in the software, manuals and

specifications concerning FP-XH M8N Control Unit and Servo Amplifier A6N/A5N.

FP-XH M8N

Control Unit A6N/A5N Description

- General-purpose

monitor input

Five inputs of symbols SI-MON1 to SI-MON5 are allocated on

the A6N/A5N side.

By default, the general-purpose monitor input (mark: SI-

MON1) is allocatd to the terminal on the servo amplifier side.

To read the general-purpose input (mark: SI-MON2), it is

necessary to change the parameter on the servo amplifier

side.

RTEX general-

purpose input -

Up to two points (marks: SI-MON1 to SI-MON2) of the

general-purpose monitor inputs on the A6N/A5N side can be

read on the FP-XH M8N control Unit side. They are allocated

to the I/O input area (WX125).

- RTEX operation

output

On the A6N/A5N side, two outputs of marks EX-OUT1 and

EX-OUT2 are allocated.

By default, the RTEX operation output (mark: EX-OUT1) is

allocatd to the terminal on the servo amplifier side. To use the

RTEX operation output (mark: EX-OUT2), it is necessary to

change the parameter on the servo amplifier side.

RTEX general-

purpose output -

On the FP-XH M8N Control Unit, the two "RTEX operation

outputs" connected to the A6N/A5N can be controlled with

user programs. The FP-XH M8N Control Unit side si allocated

to the I/O output area (WY125).

General-purpose

output part -

It indicatest the 8-point DC input circuits and 8-point transistor

output circuits connected to the terminal block of the FP-XH

M8N Control Unit.

Motion control part -

It indicates the parts relating to the motor control, interface for

the RTEX network and pulse input interface in the FP-XH

M8N Control Unit.

Axis number Node number

The axis numbers controlled by the FP-XH M8N Control Unit

match the node numbers of the servo amplifier connected to

the RTEX network.

Table of Contents

1. System Structure ............................................................... 1-1

1.1 Overview of System .............................................................................. 1-2

1.1.1 Funcntions of Control Unit.......................................................................1-2

1.1.2 Outline of Specifications..........................................................................1-3

1.2 Unit List................................................................................................. 1-4

1.2.1 FP-XH M8N Control Unit .........................................................................1-4

1.2.2 FP-X Expansion Unit ...............................................................................1-4

1.2.3 FP-X Expansion FP0 Adapter .................................................................1-5

1.2.4 FP-X Add-on Cassette (Communication Cassette) ................................1-5

1.2.5 FP-X Add-on Cassette (Function Cassette)............................................1-5

1.3 Unit Type and Product Number............................................................. 1-6

1.3.1 FP-XH M8N16PD Control Unit................................................................1-6

1.3.2 FP-X Expansion Unit ...............................................................................1-6

1.3.3 FP-X Expansion FP0 Adapter .................................................................1-7

1.3.4 FP-X Add-on Cassette (Communication Cassette) ................................1-7

1.3.5 FP-X Add-on Cassette (Function Cassette)............................................1-7

1.3.6 Options ....................................................................................................1-7

1.3.7 Repair Parts ............................................................................................1-8

1.4 Restrictions on Unit Combinations ........................................................ 1-9

1.4.1 Restrictions on FP-X Expansion Units ....................................................1-9

1.4.2 Restrictions on FP-X Expansion Adapter..............................................1-11

1.4.3 Restrictions on Add-on cassette Combination ......................................1-12

1.4.4 Restrictions on Communication Function .............................................1-14

1.5 Restrictions on Servo Amplifier ........................................................... 1-15

1.5.1 Restrictions on Parameter Settings.......................................................1-15

1.5.2Combination of Parameters and Home Return Methods ......................1-16

Contents

2. Control Unit Specifications ............................................... 2-1

2.1 Parts Name and Funcations ..................................................................2-2

2.1.1 Control Unit .............................................................................................2-2

2.1.2 Status Indicator LEDs..............................................................................2-4

2.1.3 COM0 Port Specifications .......................................................................2-5

2.2 Power Supply Specifications .................................................................2-6

2.3 Input / Output Specifications (General-purpose input/output part)..........2-7

2.3.1 Input Specifications .................................................................................2-7

2.3.2 Output Specifications ..............................................................................2-8

2.4 Input Specifications (Pulse Input Part) ...................................................2-9

3. I/O Allocation...................................................................... 3-1

3.1 Basic I/O Assignment ............................................................................3-2

3.1.1 Counting Method of I/O Numbers ...........................................................3-2

3.1.2 I/O Number Assignment Method.............................................................3-2

3.2 List of I/O Numbers for Units .................................................................3-4

3.2.1 FP-XH M8N Control Unit (General-purpose I/O Part).............................3-4

3.2.2 FP-XH M8N Control Unit (Motion Control Part) ......................................3-5

3.2.3 FP-X Expansion Unit ...............................................................................3-7

3.2.4 FP-X Function Cassette ..........................................................................3-8

3.3 Assignment of FP0 Expansion Units......................................................3-9

3.3.1 I/O Number Assignment Method.............................................................3-9

3.3.2 Types and I/O Numbers of FP0R Expansion Units...............................3-10

3.3.3 Types and I/O Numbers of FP0 Expansion Units .................................3-11

3.4 Detailed I/O Information of Motion Control Part ...................................3-12

Table of Contents

vii

4. Installation .......................................................................... 4-1

4.1 Installation............................................................................................. 4-2

4.1.1 Installation Environment and Space........................................................4-2

4.2 Backup Battery Installation.................................................................... 4-4

4.2.1 Backup Battery Installation......................................................................4-4

4.3 Add-on cassette Installation .................................................................. 4-5

4.3.1 Precautions for Installing Add-on cassettes ............................................4-5

4.3.2 Communications Cassette Installation ....................................................4-5

4.3.3 Function Cassette Installation .................................................................4-6

4.4 Connecting FP-X Expansion Unit .......................................................... 4-7

4.4.1 Setup of Terminal Setting Switches ........................................................4-7

4.4.2 Confirmation of FP-X Expansion Cables ................................................4-7

4.4.3 Connecting FP-X expansion unit.............................................................4-8

4.5 Connecting FP0 Expansion Unit ........................................................... 4-9

4.5.1 Connecting FP0 Expansion Unit .............................................................4-9

4.5.2 Connecting FP-X Expansion FP0 Adapter............................................4-10

4.6 Installation........................................................................................... 4-11

4.6.1 Installation and Removal for DIN Rail ...................................................4-11

4.6.2 Mounting with Screws ...........................................................................4-12

5. Wiring of Power Supply and General-purpose I/O Parts . 5-1

5.1 Terminal Arrangement .......................................................................... 5-2

5.1.1 Power Supply and General-purpose I/O Parts........................................5-2

5.2 Wiring of Power Supply......................................................................... 5-3

5.2.1 General Precautions ...............................................................................5-3

5.2.2 Grounding................................................................................................5-3

5.2.3 Power Supply of Control Unit / Expansion Unit.......................................5-4

5.2.4 Power Supply of FP-X Expansion FP0 Adapter / FP0 Expansion Unit...5-6

Contents

viii

5.3 Wiring of Input and Output.....................................................................5-8

5.3.1 Precautions Regarding Input and Output Wirings...................................5-8

5.3.2 Input Wiring .............................................................................................5-9

5.3.3 Output Wiring ........................................................................................5-11

5.4 Wiring of Terminal Block......................................................................5-12

5.4.1 Suitable Wires .......................................................................................5-12

5.4.2 Terminal Block Cover ............................................................................5-12

5.4.3 Installation and Removal of Terminal Block ..........................................5-13

5.5 Safety Measures .................................................................................5-14

5.5.1 Safety Measures ...................................................................................5-14

5.5.2 Momentary Power Failures ...................................................................5-15

5.5.3 Watchdog Timer ....................................................................................5-15

6. Wiring of Motion I/O Parts................................................. 6-1

6.1 Terminal Layout Diagram ......................................................................6-2

6.2 Settings on Servo Amplifier ...................................................................6-3

6.2.1 Checking Rotary Switches ......................................................................6-3

6.2.2 Connection of Limit Input and Near Home Input .....................................6-4

6.2.3 Combination of Parameters and Home Return Methods ........................6-5

6.2.4 Connection of General-purpose Monitor Input ........................................6-6

6.2.5 Connection of RTEX Operation Output...................................................6-6

6.3 Connection of Network ..........................................................................6-7

6.3.1 Wiring Method .........................................................................................6-7

6.3.2 Precautions on Wiring .............................................................................6-7

6.4 Pulse Input Connection .........................................................................6-8

6.4.1 Linear Driver Type...................................................................................6-8

6.4.2 Transistor Open-collector Type...............................................................6-8

6.4.3 Transistor Resistor Pulling Up Type........................................................6-8

6.4.4 Precautions on Wiring ...........................................................................6-10

6.4.5 Specifications of Scattered Cable Connectors......................................6-10

6.4.6 Usage of Scattered Cable Connector ...................................................6-11

Inhaltsverzeichnis

Andere Panasonic Steuereinheit Handbücher

Panasonic

Panasonic S-LINK V Bedienungsanleitung

Panasonic

Panasonic CF-BAU0512U Bedienungsanleitung

Panasonic

Panasonic AK-HCU250P Bedienungsanleitung

Panasonic

Panasonic HIT VBHN340SA17E Bedienungsanleitung

Panasonic

Panasonic GPKS162CUD - CONTROL UNIT Bedienungsanleitung

Panasonic

Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM Bedienungsanleitung

Panasonic

Panasonic AKHCU200 Bedienungsanleitung

Panasonic

Panasonic WX-CC411BP Bedienungsanleitung

Panasonic

Panasonic AFP0HC32ET Bedienungsanleitung

Panasonic

Panasonic AJ-EC3P Bedienungsanleitung

Panasonic

Panasonic VBHN240SE10 Bedienungsanleitung

Panasonic

Panasonic SF-C21 Bedienungsanleitung

Panasonic

Panasonic FP0R Series Bedienungsanleitung

Panasonic

Panasonic eUniStone Leitfaden

Panasonic

Panasonic KX-NT307 Bedienungsanleitung

Panasonic

Panasonic FP7 Series Bedienungsanleitung

Panasonic

Panasonic WVPS104C - CAMERA DRIVE UNIT Bedienungsanleitung

Panasonic

Panasonic AK-HCU3550EA Bedienungsanleitung

Panasonic

Panasonic INDUSTRY PAN9028 Kurzanleitung zur Einrichtung

Panasonic

Panasonic WV-RC550 Bedienungsanleitung

Panasonic

Panasonic WH-ADC0309H3E5 Bedienungsanleitung

Panasonic

Panasonic YEP0PTA184 Bedienungsanleitung

Panasonic

Panasonic GPKS162CUD - CONTROL UNIT Bedienungsanleitung

Panasonic

Panasonic AK-UCU600P Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung