Panasonic KX-TCD410AXM Bedienungsanleitung

ORDER NO. KM40308175C3

Telephone Equipment

KX-TCD410AXM / KX-A141AXM / KX-A142AXM

Digital Cordless Phone

Metalic Grey Version

(for Asia, Middle Near East and Other areas)

SPECIFICATIONS

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

Unauthorized copying and distribution is a violation of law.

1. ABOUT LEAD FREE SOLDER (PbF: Pb free)

Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to

standard solder or solder that contains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process

which is made from Tin (Sn), Silver (Ag), and Copper (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB.

For service and repair work we suggest using the same type of solder although, with some

precautions, standard Pb solder can also be used.

Caution

- PbF solder has a melting point that is 50°F ~70°F (30°C ~ 40°C) higher

than Pb solder. Please use a soldering iron with temperature control

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

and adjust it to 700°F ± 20°F (370°C ± 10°C). In case of using high

temperature soldering iron, please be careful not to heat too long.

- PbF solder will tend to splash if it is heated much higher than its

melting point, approximately 1100°F (600°C).

- If you must use Pb solder on a PCB manufactured using PbF solder,

remove as much of the original PbF solder as possible and be sure

that any remaining is melted prior to applying the Pb solder.

- When applying PbF solder to double layered boards, please check the

component side for excess which may flow onto the opposite side

(See the figure below).

1.1. Suggested PbF Solder

There are several types of PbF solder available commercially. While this product is manufactured

using Tin, Silver, and Copper

(Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please

check the manufac

turer’s specific instructions for the melting points of their products and any precautions for using

their product with other

materials.

The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm,

0.6mm and 1.0mm.

1.2. How to recognize that Pb Free solder is used

1.2.1. Base Unit PCB

(Component View)

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

(Flow Solder Side View)

Note:

The location of the “PbF“ marks is subject to change without notice.

1.2.2. Handset PCB

(Component View)

(Flow Solder Side View)

Note:

The location of the “PbF“ marks is subject to change without notice.

1.2.3. Charger Unit PCB

Note:

The location of the “PbF“ marks is subject to change without notice.

2. FOR SERVICE TECHNICIANS

ICs and LSIs are vulnerable to static electricity.

When repairing, the following precautions will help prevent recurring malfunctions.

1. Cover the plastic parts boxes with aluminum foil.

2. Ground the soldering irons.

3. Use a conductive mat on the worktable.

4. Do not touch IC or LSI pins with bare fingers.

3. CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type

recommendenced by the manufacturer.

Dispose of used batteries according to the manufacture’s Instructions.

4. BATTERY

4.1. Battery Installation

Please ensure the batteries are inserted as shown. part should be inserted first.

Close the cover as indicated by the arrow.

- When you replace the batteries, part should be removed first.

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

4.2. Battery Charge

At the time of shipment, the batteries are not charged. To charge, place the handset on the base unit.

Please charge the batteries for about 7 hours before initial use. During charging, the battery icon is as

shown below.

The handset which power is off will be turned on automatically when it is placed on the base unit.

In normal use, the handset and the base unit should be powered on at all times.

Note for Service:

The battery strength may not be indicated correctly if the battery is disconnected and connected

again, even after it is fully charged.

In that case, by recharging the battery as mentioned above, you will get a correct indication of the

battery strength.

4.3. Battery Life

- Battery life is dependent on use and conditions but in general when

using fully charged Ni-MH batteries (700 mAh):

Talk time: 10hrs approx.

Standby time: 120hrs approx.

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

- When using Ni-Cd batteries (250 mAh):

Talk time: 4hrs approx.

Standby time: 40hrs approx.

(Times indicated are for peak performance)

- The batteries reach peak performance after several full charge/

discharge cycles.

- The batteries cannot be overcharged unless they are repeatedly

removed and replaced.

- If battery life is shortened then please check that battery and charge

terminals are clean.

- For maximum battery life, it is recommended that the handset is not

recharged until battery icon flashes .

4.4. Replacing the Batteries

If the icon flashes after a few telephone calls even when the handset batteries have been

fully charged, 2 batteries must be replaced.

Charge new batteries for approximately 7 hours before initial use.

(The telephone line cord must not be connected to the telephone socket at this time).

When replacing the batteries, ensure that the correct battery type is selected.

- To exit the operation, press any time.

- Do not use non-rechargeable batteries. If non-rechargeable batteries

are fitted and start charging, it may cause the leakage of the battery

electrolyte.

Please use only Panasonic HHR-4EPT(Ni-MH) or P-4NPT(Ni-Cd) batteries.

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

Note for Service:

When Ni-Cd batteries are fitted with the setting in

, icon might disappear and stop charging even if the handset is

on the cradle for avoiding overcharge.

5. LOCATION OF CONTROLS

5.1. Base Unit

5.2. Handset

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

6. SETTINGS

6.1. Connection

6.1.1. Base Unit

Plug in the AC adaptor and the telephone line cord in order 1, 2, 3, 4.

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

The AC adaptor must remain connected at all times (It is normal for the adaptor to feel warm during

use).

- Never install telephone wiring during a lightning storm.

- The telephone will not work during a power failure. We therefore

recommend you use a standard telephone and T Adaptor to connect

this Digital Cordless Phone to the line. Your Panasonic Sales Shop can

offer you more information about connection possibilities.

6.1.2. Charger Unit

The AC adaptor must remain connected at all times (It is normal for the adaptor to feel warm during

use).

6.2. Symbols Used in This Service Manual

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

6.3. PIN Code

6.3.1. Base Unit

- To exit the operation, press any time.

For Service Hint:

* : If the current 4-digit PIN is forgotten, press and you

will be able to enter new PIN.

As for the case that Base Unit and Handset are not linked with, refer to Reset Base Unit PIN to Default

(0000) -When There is NO Handset Registered- ()

6.3.2. Handset

www.freeservicemanuals.info

11/8/2014

Digitized in Heiloo, Holland

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Schnurloses Telefon Handbücher

Panasonic

Panasonic KX-TG8200E Bedienungsanleitung

Panasonic

Panasonic KX-TGC380C Bedienungsanleitung

Panasonic

Panasonic KX-TGA648AZ Bedienungsanleitung

Panasonic

Panasonic KX-UDT121 Bedienungsanleitung

Panasonic

Panasonic KX-TG2382B - 2.4GHz Phone System Bedienungsanleitung

Panasonic

Panasonic KX-TGE432 Bedienungsanleitung

Panasonic

Panasonic KX-TG2551ALS, KX-TG2551NZS Bedienungsanleitung

Panasonic

Panasonic KX-TCD961EB Bedienungsanleitung

Panasonic

Panasonic KX-TCD810HK Bedienungsanleitung

Panasonic

Panasonic KX-TCD715ALM Bedienungsanleitung

Panasonic

Panasonic KX-TS85EXW Bedienungsanleitung

Panasonic

Panasonic KX-TG7841BX Bedienungsanleitung

Panasonic

Panasonic KXTC935B - CORDLESS 900 ANALOG Bedienungsanleitung

Panasonic

Panasonic KX-TG6500 Bedienungsanleitung

Panasonic

Panasonic KX-TG6611E Bedienungsanleitung

Panasonic

Panasonic KX-TGE662 Bedienungsanleitung

Panasonic

Panasonic TG2550 - 2.4 Gigarange Cordless Phone Bedienungsanleitung

Panasonic

Panasonic KX-TG6021NZ Bedienungsanleitung

Panasonic

Panasonic KX-TGE632 Bedienungsanleitung

Panasonic

Panasonic KX-TG6811SA Bedienungsanleitung

Panasonic

Panasonic KX-TCA155 Bedienungsanleitung

Panasonic

Panasonic KX-TG2501 Bedienungsanleitung

Panasonic

Panasonic KX-TG2219B Bedienungsanleitung

Panasonic

Panasonic KX-TCD280FX Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung

GE 27930 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung

Uniden

Uniden D1785 Series Bedienungsanleitung

Binatone

Binatone Style 1820 Bedienungsanleitung