Panasonic AU-EVA1 Bedienungsanleitung
SKAARHOJ DEVICE CORES
Device: Panasonic AU-EVA1
Introduction
The Device Core “Panasonic EVA1” is used for controlling the AU-EVA1 camera. The goal of this manual is
to help configuring a SKAARHOJ interface to control features available in the Device Core at this present
time.
Multicam Control
Please notice with the release of UniSketch v2.4.16 Multicam Control have been enabled. Prior to v2.4.16
only a single camera could be controlled from the Device Core. With the update up to 4 cameras can be
controlled from a single Device Core. Please see information in the section “Multicam Control”
Setting up Camera
In order to control the camera a USB/Ethernet adapter must be utilized from the USB2.0 HOST port on the
camera. All communication between a SKAARHOJ interface and the camera is done via IP. The
implementation have been done on version 0.00-00-8.02.
Panasonic recommends to use Plugable USB 3.0 Gigabit Eathernet Adapter or UGREEN USB3.0 to RJ45
Ethernet Adapter 20256
1
SKAARHOJ DEVICE CORES
A number of actions are required for a SKAARHOJ controller to communicate with the camera. Please
follow these procedures in the MENU —> NETWORK SETTINGS. The aim of the procedures is to set a
static IP address on the camera which the SKAARHOJ controller can connect to and to create a user
account for authentication. You can use a different IP address as long as the Panasonic Device Core on the
SKAARHOJ controller reflects this.
•NETWORK SEL: WLAN
•NETWORK FUNC - add a account
•Account name: skaarhoj
•Account password: 12345678
•NETWORK PROPERTY - set static IP
•TYPE: INFRA(SELECT)
•DHCP: OFF
•IP ADDRESS: 192.168.10.178
•SUBNET MASK: 255.255.255.0
•DEFAULT GATEWAY: 192.168.10.1
•PRIMANRY DNS: 192.168.10.2
2
SKAARHOJ DEVICE CORES
Setting up a RCPv2 controller using the default configuration “Panasonic AU-EVA1”
Please follow these instructions if you have a RCPv2 and want to use it with the Panasonic AU-EVA1
camera.
If you RCPv2 have been shipped preconfigured with the “Panasonic AU-EVA1” configuration please go to
section “Confirm Connection”
If you have a RCPv2 and want to use the default configuration “Panasonic AU-EVA1” please follow these
steps
-Download and install the Firmware Updater Application (https://www.skaarhoj.com/support/firmware-
updater/)
-Connect the RCPv2 with the USB programming cable (if you are on Windows and have multiple com
ports available please see the section “Port selection on Windows” in the Installation and Operation
Manual (https://www.skaarhoj.com/support/manuals/)
-Press “Online Configuration” in the Firmware Application
3
SKAARHOJ DEVICE CORES
Direct Selection of Default Config
If no custom configurations have been made on the RCPv2
you will be presented with this interface
Selection of Default Config
If custom configurations have been made on the RCPv2 you
will be presented with this interface
Select the “Panasonic AU-EVA1” config in the drop down list. This will
load the configuration on the configuration page. Then go to the
Firmware Application and press “Check for updates”.
This will generate a firmware file on our server and download it to the
controller.
Notice on Windows the Port dropdown will display “COM” ports.
Please see section “Port selection on Windows” in Installation and
Operation manual https://www.skaarhoj.com/support/manuals/
Notice on Windows the Port dropdown will display “COM” ports.
Please see section “Port selection on Windows” in Installation and
Operation manual https://www.skaarhoj.com/support/manuals/
Select the “Panasonic AU-EVA1” config and then go to the Firmware
Application and press “Check for updates”. This will generate a
firmware file on our server and download it to the controller.
If you want to use different IP addresses then alter “Network
configuration” and press “Save Network Configuration” and then
press “Check for updates” in the Firmware Application
4
SKAARHOJ DEVICE CORES
Confirm Connection
If the RCPv2 have come preconfigured with the Panasonic Configuration or you have just successfully
downloaded the Firmware to the RCPv2, then it is ready to control the camera provided you have followed
the steps in the “Setting up Camera” section. It is important that the IP address you have set on the camera
matches the IP address of the Panasonic EVA1 Device Core.
Connection to the camera can be confirmed from the Serial Monitor with the commands as shown below.
Check IP Addresses on SKAARHOJ Controller
If you have issues connecting to the camera it is recommend to confirm that IP settings are correct. A way
to confirm IP settings on the SKAARHOJ controller is using the Serial Monitor in the Firmware Application
and check IP settings in the boot up process.
5
SKAARHOJ DEVICE CORES
Using different IP address on Panasonic AU-EVA1 camera
You can set a different IP address on the camera as long as the Device Core IP address is updated as well.
You can use the “IP Configuration” option in the Firmware Application to change the Device Core IP
address.
6
SKAARHOJ DEVICE CORES
Debugging Connection between SKAARHOJ Controller and Camera
If IP settings are correct but the Account name is not correct the Serial Monitor will report
“Camera Error: Wrong user”
If the Account name is correct but the password is not the Serial Monitor will report “Camera Error: Wrong
User” after reporting that the user is acknowledged.
7
SKAARHOJ DEVICE CORES
Alternative way of Downloading and Installing the Firmware on a RCPv2
If you have issues using the Firmware Application to generate and installing the Firmware on your RCPv2
please follow these steps
-Press “Online Configuration” in the Firmware Application
Direct Selection of Default Config
If no custom configurations have been made on the RCPv2
you will be presented with this interface
Selection of Default Config
If custom configurations have been made on the RCPv2 you
will be presented with this interface
Press the “Firmware Overview” tab and press “Generate Firmware”
Select the “Panasonic AU-EVA1” config and press “Advanced”
Select the “Panasonic AU-EVA1” config in the drop down list.
8
SKAARHOJ DEVICE CORES
Open the Firmware Updater Application and use the “Load Firmware from file” in the option tab
Select the “.hex” firmware file. Naming might be different dependent on browser but it should be a .hex file to be selected.
When done the Firmware Updater application reports “Firmware successfully updated”
On PC.
Important to select proper COM port. See “Port selection on
Windows” in Installation and Operation manual https://
www.skaarhoj.com/support/manuals/ “
After the firmware have been generated press “Download”
Notice on Windows the Port dropdown will display “COM” ports.
Please see section “Port selection on Windows” in Installation and
Operation manual https://www.skaarhoj.com/support/manuals/
On Mac
9
SKAARHOJ DEVICE CORES
Setting up Controller
This section is only relevant if you are building a configuration from scratch.
The Device Core “Panasonic AU-EVA1” must be added to your controller
The Device Core must have the IP address matching, the one set on the camera it self (see “Setting up
Camera” section).
Connection to the camera can be confirmed from the Serial Monitor with the command: PansonicEVA:
Connected
10
Andere Handbücher für AU-EVA1
3
Inhaltsverzeichnis
Andere Panasonic Digitalkamera Handbücher
Panasonic
Panasonic Lumix DMC-FZ47 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-TZ57 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-FX90 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-FH24 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-GX80KEBK Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-FS5P Bedienungsanleitung
Panasonic
Panasonic LUMIX DMC-FX580 Bedienungsanleitung
Panasonic
Panasonic LUMIX DMC-G7H Montage- und Serviceanleitung
Panasonic
Panasonic Lumix DMC-FZ150 Montage- und Serviceanleitung
Panasonic
Panasonic AJ-D610WBp Bedienungsanleitung
Panasonic
Panasonic LUMIX DMC-FX8EB Bedienungsanleitung
Panasonic
Panasonic DMC-GH1K - Lumix Digital Camera Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-FZ150 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-LC20 Bedienungsanleitung
Panasonic
Panasonic DMC-ZS40 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-FT4 Technische Daten
Panasonic
Panasonic LUMIX DC-GH6 Bedienungsanleitung
Panasonic
Panasonic Lumix DMC-FZ20GN Bedienungsanleitung
Panasonic
Panasonic LUMIX DMC-FZ2EN Bedienungsanleitung
Panasonic
Panasonic LUMIX DMC-ZX3EB Bedienungsanleitung
