Panasonic AYJP2000 - PROFESSIONAL JOG Bedienungsanleitung

Before attempting to connect or operate this product, please read these instructions completely



Professional Jog Pad

AY-JP2000

Warning:

This equipment generates and uses radio frequency

energy and if not installed and used properly, i.e., in

strict accordance with the instruction manual, may

cause harmful interference to radio communications.

It has been tested and found to comply with the limits

for a Class A computing device pursuant to Subpart J

of Part 15 of FCC Rules, which are designed to pro-

vide reasonable protection against such interference

when operated in a commercial environment.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product's enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock to

persons.

The exclamation point within an equi-

lateral triangle is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature accompa-

nying the appliance.

The serial number of this product may be found on the

bottom of the unit.

You should note the serial number of this unit in the

space provided and retain this book as a permanent

record of your purchase to aid identification in the

event of theft.

Model No. AY-JP2000

Serial No.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK). NO USER SER-

VICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PER-

SONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SA 1965

SA 1966

For U.S.A

CONTENTS

PREFACE ........................................................................................................................................................................... 1

PRECAUTIONS .................................................................................................................................................................. 1

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ........................................................................................... 2

ACCESSORY CABLE ......................................................................................................................................................... 5

CONNECTIONS.................................................................................................................................................................. 6

INSTALLING THE SOFTWARE........................................................................................................................................... 8

SPECIFICATIONS .............................................................................................................................................................. 9

ACCESSORIES................................................................................................................................................................... 9

3 1

• The jog pad uses the keys and jog/shuttle dial, wipe

lever, positioner and audio fader controls as well as the

number keys (0 to 9) for ensuring that non-linear editing

work will be performed very efficiently.

• The four audio faders make it possible to set the audio

levels simultaneously for four channels.

• The rotary encoders enable the modify settings and

video level to be finely adjusted.

• Frequently used functions can be allocated to the user

keys as short-cut keys.

• The trackball enables the same operations as those of

a mouse to be performed on the jog pad.

PREFACE

• Do not attempt to disassemble the unit.

In order to prevent electric shock, do not remove

screws or covers. There are no user-serviceable parts

inside.

Do refer all servicing to qualified service personal.

• Handle the unit with care.

Do not abuse the unit. Avoid striking, shaking, etc.

It could be damaged by improper handling or storage.

• Do not place heavy objects on top of the unit.

• Do not expose the unit to rain or moisture, or try to

operate it in wet areas.

Do take immediate action if the unit becomes wet. Turn

the power off and refer servicing to qualified service

personal. Moisture can damage the unit and also

create the danger of electric shock.

• Before proceeding with maintenance, disconnect the

power plug from the power outlet to ensure safety.

Failure to do this may cause electric shock.

• Do not use strong or abrasive detergents when

cleaning the unit body.

Do use a dry cloth to clean the unit when dirty.

In case the dirt is hard to remove, use a mild detergent

and wipe gently.

• In the winter season or at other times when the unit is

cold, before attempting to operate the unit, raise the

room temperature gradually so that the unit will be

warmed up. If the temperature is raised suddenly,

condensation will form inside the unit.

• Do not operate the unit beyond its temperature,

humidity or power source ratings.

Do not use the unit in an extreme environment where

high temperature or high humidity exist.

Use the unit under conditions where temperature is

within 32°F ~ 95°F (0°C ~ +35°C), and humidity is

within 10% ~ 90%.

PRECAUTIONS

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

Operating panel

Rear panel

For further details on operation, refer to the operating instructions of the software program you are using.

5 3

Positioner

Used to set the key positions.

Rotary encoders [R1 ~ R4]

Used to adjust the video levels and modify settings.

Audio faders [A1 ~ A4]

Used to adjust the audio levels.

ESC

Used to cancel the setting panel.

DIG

Used to switch to the manual digitizer.

P1 ~ P4

Used to switch to the clip editor.

SEQ

Used to switch to the sequence editor.

UNDO

Used to undo the operation performed immediately

before.

REDO

Used to redo the operation which was undone by

“UNDO”.

TAB

Used in the same way as the “TAB” key on a

keyboard. It jumps ahead to the next item.

HOME/END

Used to jump to the start or end point (toggle

operation) of a sequence.

GOTO/SEARCH

Used to jump to a mark in or out point (toggle

operation).

ZOOM IN (ZOOM OUT)

Used to zoom in on (magnify) the time line. Used to

zoom out when it is pressed while “SHIFT” is held

down.

DIVIDE (MARK CUE)

Used to divide a clip.

REPLACE/ASSEM (EXCHANGE)

Used to paste (replace) clips into a sequence. With

Record To Video, it switches to the assemble mode.

INSERT/INSERT

Used to paste (insert) clips into a sequence. With

Record To Video, it switches to the insert mode.

DELETE/IMMED (BS)

Used to delete clips. With Record To Video, it

switches to the immediate mode.

When it is pressed while “SHIFT” is held down, the

two keys function as the backspace key.

REMOVE/REC (EXIT)

Used to remove clips (without moving the following

clips forward to close up the gaps left). With Record

To Video or the batch digitizer, it starts recording.

When it is pressed while “SHIFT” is held down, the

window with the focus is closed.

Wipe lever

Used to set wipe or the DVE preview or learn setting.

PLAY

Used to play a tape in an external VCR when the

time line or clips are to be played.

Used to preview wipe or DVE.

Used to rewind the tape in the external VCR.

Used to advance the tape in the external VCR frame

by frame (in the reverse direction).

/STBY

Used to set the external VCR to the still mode. When

it is pressed while “CTRL” is held down, the external

VCR is switched between the standby ON and OFF

mode.

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

Used to advance the tape in the external VCR frame

by frame (in the forward direction).

Used to fast forward the tape in the external VCR.

STOP/EJECT

Used to stop play. The external VCR is set to the

stop mode. When it is pressed while “CTRL” is held

down, the tape in the external VCR is ejected.

MARK IN

Used to set the mark in point. When it is pressed

while “SHIFT” is held down, the in point grip can be

selected. When it is pressed while “CTRL” is held

down, the mark in point is deleted.

MARK OUT

Used to set the mark out point. When it is pressed

while “SHIFT” is held down, the out point grip can be

selected. When it is pressed while “CTRL” is held

down, the mark out point is deleted.

ENTER

Used to enter the selected items. With the batch

digitizer, it enters the in and out points.

SHIFT

Used to select the functions of the keys.

CTRL

Used to select the functions of the keys.

Jog/shuttle dial

Jog and shuttle modes are selected (toggle

operation) by pressing down the dial.

In jog mode, the tape is played frame by frame in the

forward direction (when the dial is turned clockwise) or

reverse direction (when it is turned counterclockwise).

In shuttle mode, the tape is played at a variable

speed in the forward direction (when the dial is

turned clockwise) or reverse direction (when it is

turned counterclockwise).

LED

The lighted LED shows the number key mode. The

mode is selected by pressing the “USER”, “NUM”,

“ARROW” and “AV” keys.

USER

Used to switch to the user mode.

In the user mode, the number keys perform the

functions which have been allocated to them.

Frequently used functions can be allocated to the

user keys.

For details on how to allocate these functions, refer

to the operating instructions of the software program

you are using.

NUM

Used to switch to the number input mode.

In the number input mode, the number keys function

as number input keys.

ARROW

Used to switch to the cursor mode.

In the cursor mode, the number keys (2, 4, 6 and 8

keys) function as arrow keys.

Used to switch to the track selection mode.

In the track selection mode, the number keys

function as track selection keys.

For further details on operation, refer to the operating

instructions of the software program you are using.

Number keys

The way in which these keys are used differs

depending on the mode (“USER”, “NUM”, “ARROW”

and “AV”). The “+” and “–” keys are used to

advance the images frame by frame.

The ENTER key enters the selected item.

Trackball

This can perform the same operations as those of a

mouse.

Connect the trackball cable following the instructions

in Connections.

[MOUSE] connector

The trackball cable (supplied accessory) is

connected to this connector.

[JOGPAD] connector

The jog pad cable (VCR/JOGPAD cable) is

connected to this connector.

7 5

ACCESSORY CABLE

Track Ball Cable

Jogpad Mouse

Connector

Mini DIN

6-pin type

Mouse Connector

on Main Unit

Mini DIN

6-pin type

CONNECTIONS Ask your dealer to do this.

Connection with the AY-NE2000, WJ-MX1000 series or WJ-MX1200 series

Plug one end of the jog pad connecting cable (accessory supplied with the AY-NE2000, WJ-MX1000 series and

WJ-MX1200 series) into the connector on the rear panel of the jog pad and the other end into the JOGPAD connector on

the rear panel of the main unit, and then tighten the screws.

Plug one end of the trackball connecting cable (supplied accessory) into the connector on the rear panel of the jog pad

and the other end into the MOUSE connector on the rear panel of the main unit. Once the trackball has been connected,

it is not possible to use another mouse (PS/2) or serial mouse at the same time as the trackball. However, the tablet

(ArtPAD made by WACOM) can be used simultaneously.

The power must be turned off before these cables are connected.

MAIN UNIT

JOG PADMOUSE

‘

AC IN

IN1

IN2

LR RL

OUT1

OUT2

AUDIO

OUT

OUT1

OUT2

BALANCED

AUDIO OUT

IN1 IN2

BALANCED

AUDIO IN

LRR

CONTROL 1 CONTROL 2 JOG PAD

Y/C COMPOSITE

YPBPR

IN1

IN2

G/L IN

LOOP

Y/C COMPOSITE Y PBPRADV REF

OUT

OUT1

OUT2

TC IN

VIDEO

AUTO

VIDEO

OUT TC OUT

AUDIO

SEE MANUAL

KB MOUSE SEPIAL 1 SEPIAL 2 PRINTER S-VGA

SCSI AUDIO SCSI VIDEO 1 SCSI VIDEO 2 SCSI VIDEO 3

VIDEO(DIGITAL)

IN OUT AUDIO

(AES/EBU)

IN OUT

Main Unit

Jog pad

Track Ball Cable

(Supplied accessory)

Tighten these screws after

plugging in the connector.

Jog pad Cable

It is necessary to first mount the professional jog pad ROM kit (AY-PB2003) when WJ-MX1000 or WJ-MX1200 series is

used.

MAIN UNIT

JOG PADMOUSE

Computer (Rear panel)

MOUSE connector

JOG Board

Tighten these screws after

plugging in the connector.

JOGPAD

Mini DIN 8-pin

Connector

Track Ball Cable

(Supplied

accessory)

VCR/JOGPAD

Cable

Jog pad

Connection with DVEdit

Connect one end of the VCR/JOGPAD cable (accessory supplied with the AY-RP500) into the JOGPAD connector (mini

DIN 8-pin) on the JOG board and the other end into the connector (D-sub 9-pin) on the rear panel of the jog pad.

Tighten the screws on the parts connected to the rear panel of the jog pad.

Plug one end of the trackball connecting cable (supplied accessory) into the connector on the rear panel of the jog pad

and the other end into the MOUSE connector on the rear panel of the computer. Once the trackball has been

connected, it is not possible to use another mouse (PS/2), serial mouse or USB mouse at the same time as the trackball.

However, the tablet (ArtPAD made by WACOM) can be used simultaneously.

The power must be turned off before these cables are connected.

It is necessary to first mount the professional jog pad ROM kit (AY-PB502) when DVEdit (AY-RP500) is used.

INSTALLING THE SOFTWARE Ask your dealer to do this.

Install the accessory upgrade software program only if the main unit used is the AY-NE2000, WJ-MX1000 series or

WJ-MX1200 series.

There is no need to install it if the DVEdit is to be used.

Before installing this upgrade, make sure that V4.0 or above of the software is installed.

Procedure

Press the [Exit] button in ToolBox to exit the system.

When the Caution window appears, click the button to restart Windows.

Insert the floppy disk labeled “Disk 1” into the floppy disk drive.

• If you are using Windows 95:

Click the [Start] button on the taskbar at the bottom of the display, and select the Run command. Input

“A:\SETUP.EXE” on the Run window, and click button.

• If you are using Windows 3.1:

Select Program Manager, and press the [F] while holding down the [Alt] key. A pull-down menu is opened. Select

the Run command. Input “A:\SETUP.EXE” on the Run window, and click button.

The setup windows appears. Click button.

The “Please insert the diskette labeled disk 2” message now appears. Insert “Disk 2” into the floppy disk drive, and

click button. Follow the instructions in the messages which appear on the monitor screen for all floppy

disks.

Andere Handbücher für AYJP2000 - PROFESSIONAL JOG

Inhaltsverzeichnis

Andere Panasonic DJ-Equipment Handbücher

Panasonic

Panasonic KX-DT390 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung