Panasonic EY7443 Bedienungsanleitung

distribution is a violation of law.

Order Number PTD1301X17CE

Cordless Auto Drill & Driver

Model No. EY7443

Europe

Oceania

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 8

5 Wiring Connection Diagram ---------------------------------16

6 Schematic Diagram ---------------------------------------------16

7 Exploded View and Replacement Parts List -----------17

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please

use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-

ing iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).

2 Specifications

3 Troubleshooting Guide

3.1. Troubleshooting Guide

3.2. Trial Operation (After Checking Troubleshooting Guide)

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

• Confirm if there is no dirt when repairing.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Check whether the LED light turns on and off each time the LED light on/off button is depressed.

• Check whether the tool detects the load and switches gears automatically during AUTO mode operation (continuous speed

adjustment).

• Check whether the gear can be fixed during HIGH/LOW mode operation.

• Check whether the tool speed is normal after repair and reassembly.

• High mode: 180 to 1,400 rpm

• Low mode: 50 to 400 rpm

• Check whether the tool may become hot in a short operation.

• Set the clutch handle to the mark and check whether the tool rotates without any clutch operation.

• Operate (rotate) the keyless chuck and check whether the chuck’fs three jaws move smoothly.

• Pull the trigger all the way back and check whether the tool stops rotating immediately when it is released.

3.2.3. Integrity

• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.

• Rotate the clutch handle and check whether the clutch switches properly.

• Check whether the keyless chuck is attached securely to the tool.

• Check whether the chuck's jaws operate properly.

• Check for the presence of any dirt or foreign matter from the repair process on the outside of the tool.

4 Disassembly and Assembly Instructions

*To assemble the tool, start with 5-12 and proceed to 5-1

*Set the clutch handle to select ''HIGH" position.

4.1. Removing the keyless chuck

4.2. Removing the plate hook

4.3. Removing the housing

4.4. Removing the Module assembly

Inhaltsverzeichnis

Andere Panasonic Bohren Handbücher

Panasonic

Panasonic EY503B Bedienungsanleitung

Panasonic

Panasonic EY6930 - HAMMER DRILL Bedienungsanleitung

Panasonic

Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG Bedienungsanleitung

Panasonic

Panasonic EY6225 - 3.6V DRILL & DRIVER Bedienungsanleitung

Panasonic

Panasonic EY7441 Bedienungsanleitung

Panasonic

Panasonic EY6450-U1 Bedienungsanleitung

Panasonic

Panasonic EY7411 - CORDLESS DRILL & DRIVER Bedienungsanleitung

Panasonic

Panasonic EY6535 - CORDLESS Bedienungsanleitung

Panasonic

Panasonic EY7410 - DRILL DRIVER 3.6V Bedienungsanleitung

Panasonic

Panasonic EY 503 Bedienungsanleitung

Panasonic

Panasonic EY6803 - HAMMER DRILL DRIVER 12V Bedienungsanleitung

Panasonic

Panasonic EY7542LN2L Bedienungsanleitung

Panasonic

Panasonic EY6405-X8 Bedienungsanleitung

Panasonic

Panasonic EY6950-X8 Bedienungsanleitung

Panasonic

Panasonic EY74A2 Bedienungsanleitung

Panasonic

Panasonic 78A1LJ Bedienungsanleitung

Panasonic

Panasonic EY6931NQKW Bedienungsanleitung

Panasonic

Panasonic EY7549 Bedienungsanleitung

Panasonic

Panasonic EY6950 - 18V HAM. DRILL&DRIVE Bedienungsanleitung

Panasonic

Panasonic EY6932 - HAMMER DRILL DRIVER Bedienungsanleitung

Panasonic

Panasonic EY6406 - CORDLES DRILL&DRIVER Bedienungsanleitung

Panasonic

Panasonic EY7440LN2L Bedienungsanleitung

Panasonic

Panasonic EY6405 - CORDLES DRILL&DRIVER Bedienungsanleitung

Panasonic

Panasonic EY7950LR2S Bedienungsanleitung

Beliebte Bohren Handbücher anderer Marken

Makita

Makita BDF456 Bedienungsanleitung

Black & Decker

Black & Decker LDX220 Bedienungsanleitung

Hitachi

Hitachi DH 40MA Bedienungsanleitung

Challenge

Challenge JO Technisches Referenzhandbuch

Makita

Makita LXFD01 Bedienungsanleitung

Festool

Festool T18+3 Bedienungsanleitung

Milwaukee

Milwaukee M12 FPDX-202X Bedienungsanleitung

EINHELL

EINHELL TE-RH 32 E Bedienungsanleitung

Makita

Makita DHP484 Bedienungsanleitung

Makita

Makita FD05 Bedienungsanleitung

Bosch

Bosch PSB 530 RA Bedienungsanleitung

Maximum

Maximum 054-1359-4 Bedienungsanleitung

Makita

Makita HP332D Bedienungsanleitung

Raider

Raider RDP-HD31H Bedienungsanleitung

Bort

Bort BPM-1400x2 Bedienungsanleitung

Black & Decker

Black & Decker 7266 Bedienungsanleitung

KENT USA

KENT USA TRD1230 Bedienungsanleitung

Bosch

Bosch GSB 19-2 RE Bedienungsanleitung