Panasonic DoubleFeature PV-D4734S Bedienungsanleitung
ORDER NO. MKE0403002C1
B3
DVD / VCR DECK
PV-D4734S / PV-D4744 / PV-D4744S / PV-D4754S / PV-D4734S-K
/ PV-D4744S-K / PV-D4754S-K
For servicing the R4-Mechanism Chassis for PV-Model, Please refer to
the R4-Mechanism-Chassis-for-PV-Model Service Manual (Order No.
MKE0401000C1).
SPECIFICATIONS
1
2
1. SAFETY PRECAUTIONS
GENERAL GUIDELINES
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are
important for safety. These parts are marked by in the Schematic
Diagrams, Circuit Board Layout, Exploded Views and Replacement
Parts List. It is essential that these criticalparts should be replaced
with manufacturerís specified parts to prevent shock, fire or other
hazards. Do not modify the original design without permission of
manufacturer.
2. An Isolation Transformer should always be used during the servicing
of DVD VCR whose chassis is not isolated from the AC power line.
Use a transformer of adequate power rating as this protects the
technician from accidents resulting in personalinjury from electrical
shocks. It will also protect DVD VCR from being damaged by
accidental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short circuit is
found, replace all parts which have been overheated or damaged by
the short circuit.
4. After servicing, see to it that all the protective devices such as
insulation barriers, insulation papers shields are properly installed.
5. After servicing, make the following leakage current checks to prevent
the customer from being exposed to shock hazards.
LEAKAGE CURRENT COLD CHECK
1. Unplug the AC cord and connect a jumper between the two prongs on
the plug.
2. Measure the resistance value, with an ohmmeter, between the
jumpered AC plug and each exposed metallic cabinet part on the
equipment such as screwheads, connectors, control shafts, etc. When
the exposed metallic part has a return path to thechassis, the reading
should be between 1 M and 5.2 M . When the exposed metal does
not have a return path to the chassis, the reading must be infinity.
3
LEAKAGE CURRENT HOT CHECK / (See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use an isolation
transformer for this check.
2. Connect a 1.5 k , 10 W resistor, in parallel with a 0.15 F capacitor,
between each exposed metallic part on the set and a good earth
ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k /V or more sensitivity, to measure the
potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each
point.
5. Reverse the AC plug in the AC outlet and repeat each of the above
measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equivalent) may be
used to make the hot checks. Leakage current must not exceed 1/2
mA. In case a measurement is outside of the limits specified, there is a
possibility of a shock hazard, andthe equipment should be repaired
and rechecked before it is returned to the customer.
Figure 1
1.1. LASER PRODUCT
CLASS I LASER PRODUCT
- This equipment is certified to comply with DHHS Rules 21 CFR Chapter
1, Subchapter J in effect as of date of manufacture. (Only for U.S.A.)
This equipment is classified as a Class I (Class 1) level LASER Product and there is no hazardous
LASER radiation with the safety protection.
Caution:
4
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Danger:
The serviceman should not remove the cover of drive unit and should not service because the drive
unit is a nonserviceable parts. Please check that the labels.
Never touch the internal parts in order to avoid EXPOSURE TO VISIBLE LASER RADIATION.
Unplug the AC power cord to the equipment when opening the top cover.
When the power switch is On, do not place your eyes close to the front panel opening door or the
other openings to look into the interior unit.
LASER Specification
Class I level A LASER Product (Class 1 level A LASER Product)
Wave Length: 647 - 677 nm (at DVD)
775 - 815 nm (at CD)
Laser Power: No hazardous radiation is emitted with the safety protection.
1.2. PRECAUTION OF LASER DIODE
CAUTION:
This unit utilizes a class III a laser. Visible laser radiation is emitted from
the optical pickup lens when the unit is turned on:
1. Do not look directly into the pickup lens.
2. Do not use optical instruments to look at the pickup lens.
3. Do not adjust the preset variable resistor on the optical pickup.
4. Do not disassemble the optical pickup unit.
5. If the optical pickup is replaced, use the manufactures specified
replacement pickup only.
6. Use of control or adjustment or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
2. PREVENTION OF ELECTRO-STATIC DISCHARGE
(ESD) TO ELECTROSTATICALLY SENSITIVE (ES)
DEVICES
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such
components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits, some field-effect transistorsand semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused
by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any ESD on your body by
touching a known earth ground. Alternatively, obtain and wear a
5
commercially available discharging ESD wrist strap, whichshould
remove electrostatic charge for potential shock reasons prior to
applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place
the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an antistatic solder removal device. Some solder removal
devices not classified as "antistatic (ESD protected)" can generate
electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical
charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package
until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparableconductive material).
7. Immediately before removing the protective material from the leads of
a replacement ES device, touch the protective material to the chassis
or circuit assembly into which the device will be installed.
CAUTION:
Be sure no power is applied to the chassis or circuit, and observe all
other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES
devices. (Otherwise harmless motion such as the brushing together of
your clothes fabric or the lifting of your foot from a carpeted floor can
generate static electricity (ESD)sufficient to damage an ES device).
“NOTE toCATV system installer:
This reminder is provided to call the CATV system installerís attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding systemof the building, as close to the point of cable entry as
practical.”
3. ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a printing on the PCB.
6
(Please refer to figures.)
CAUTION:
- Pb free solder has a higher melting point than standard solder;
Typically the melting point is 50°F - 70°F (30°C - 40°C) higher.
Please use a soldering iron with temperature control and adjust it to
700°F ± 20°F (370°C ± 10°C).
In case of using high temperature soldering iron, please be carefull not
to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F/
600°C).
- All products with the printed circuit board with printing must be
serviced with lead free solder.
When soldering or unsoldering, completely remove all of the solder
from the pins or solder area, and be sure to heat the soldering points
with the lead free solder until it melts sufficiently.
Recommendations
Recommended lead free solder composition is Sn96.5 Ag3.0 Cu0.5.
7
4. SERVICE NOTES (PLEASE READ)
4.1. SELF-DIAGNOSIS INDICATION DISPLAY
This VCR has a self-diagnosis and display function.
1. Keep pressing CH DOWN Button on VCR for over 3 seconds in Power
off condition, or keep pressing CH DOWN button on VCR in Shut off
condition.
Fig. 1-1
2. Fault code (4-digit number) will be displayed in F.I.P. as shown.
Fig. 1-2
4.1.1. Explanation of I 2 C bus transmission number
The condition of I2C bus transmission befor shut off is displayed.
Fig. 1-3
8
4.1.2. Explanation of VCR mode code number
The condition of VCR Mode before shut off is displayed.
Fig. 1-4
4.1.3. Explanation of Error code number
The detecting condition and movement of mechanism is displayed.
Fig. 1-5
9
4.1.3.1. Reason of Ejection
When an error code is 80, the reason of ejection is displayed on the F.I.P. of “TIMER”, “VCR” and
“HiFi”.
Fig. 1-6
Note:
The location of above indications is different for each type of F.I.P..
10
Andere Handbücher für DoubleFeature PV-D4734S
1
Dieses Handbuch passt für folgende Modelle
6
Andere Panasonic DVD-Player Handbücher
Panasonic
Panasonic DVD-LS80P Bedienungsanleitung
Panasonic
Panasonic DVDS58 - DVD/CD PLAYER - MULTI LANGUAGE Bedienungsanleitung
Panasonic
Panasonic DVD-RV80 Bedienungsanleitung
Panasonic
Panasonic DVD-S500EB Bedienungsanleitung
Panasonic
Panasonic DVDRV22 - DIG. VIDEO DISC PLAY Bedienungsanleitung
Panasonic
Panasonic DVD Home Theatre System Bedienungsanleitung
Panasonic
Panasonic DMP-BD50 Bedienungsanleitung
Panasonic
Panasonic DVD-S59 Bedienungsanleitung
Panasonic
Panasonic DVD-S48 Bedienungsanleitung
Panasonic
Panasonic DVD-S47 Bedienungsanleitung
Panasonic
Panasonic DVD-A112 Bedienungsanleitung
Panasonic
Panasonic DVD-S29EE Bedienungsanleitung
Panasonic
Panasonic DVD-A360A Bedienungsanleitung
Panasonic
Panasonic DIGA DMR-ES15 Bedienungsanleitung
Panasonic
Panasonic DVD-S500 Bedienungsanleitung
Panasonic
Panasonic DVDRV60 - Bedienungsanleitung
Panasonic
Panasonic DVD-S49 Bedienungsanleitung
Panasonic
Panasonic DVD-CP72P Bedienungsanleitung
Panasonic
Panasonic ET-MWP100G Bedienungsanleitung
Panasonic
Panasonic DVD-S100 Bedienungsanleitung
