Panasonic DMR-ES15EE Bedienungsanleitung

rights reserved. Unauthorized copying and

distribution is a violation of law.

DMR-ES15EE

DMR-ES15GC

DMR-ES15GCS

DMR-ES15GN

DMR-ES15GCA

Vol. 1

Colour

(S).......................Silver Type

DVD Recorder

ORDER NO.CHM0603012CE

1 Safety Precaution 3

1.1. General guidelines 3

2 Warning 4

2.1. Prevention of Electrostatic Discharge (ESD) to

Electrostatic Sensitive (ES) Devices 4

2.2. Precaution of Laser Diode 5

2.3. Service caution based on legal restrictions 6

3 Service Navigation 7

3.1. Service Information 7

3.2. Caution for DivX 7

4 Specifications 8

5 New Feature 10

5.1. About DivX 10

6 Location of Controls and Components 15

7 Operation Instructions 16

7.1. Taking out the Disc from DVD-Drive Unit when the Disc

cannot be ejected by OPEN/CLOSE button 16

8 Service Mode 17

8.1. Self-Diagnosis and Special Mode Setting 17

9 Service Fixture & Tools 25

10 Disassembly and Assembly Instructions 26

10.1. Disassembly Flow Chart 26

10.2. P.C.B. Positions 26

10.3. Top Case 27

10.4. Front Panel 27

10.5. RAM/Digital P.C.B. Module 27

10.6. DV Jack P.C.B. 28

10.7. Power P.C.B. 28

10.8. Rear Panel 29

10.9. Main P.C.B. and Front (L) P.C.B. 29

10.10. Tuner P.C.B. 29

11 Measurements and Adjustments 30

11.1. Service Positions 30

11.2. Caution for Replacing Parts 33

11.3. Standard Inspection Specifications after Making Repairs

12 Block Diagram 37

12.1. Power Supply Block Diagram 37

12.2. Analog Video Block Diagram 39

12.3. Analog Audio Block Diagram 40

12.4. Analog Timer Block Diagram 41

13 Schematic Diagram 43

13.1. Interconnection Schematic Diagram 43

13.2. Power Supply Schematic Diagram 44

13.3. Main Net (1/4) Section (Main P.C.B. (1/4)) Schematic

Diagram (M) 45

13.4. Main Net (2/4) Section (Main P.C.B. (1/4)) Schematic

Diagram (M) 46

13.5. Main Net (3/4) Section (Main P.C.B. (1/4)) Schematic

Diagram (M) 47

13.6. Main Net (4/4) Section (Main P.C.B. (1/4)) Schematic

Diagram (M) 48

13.7. A/V I/O (1/4) Section (Main P.C.B. (2/4)) Schematic

Diagram (AV) 50

13.8. A/V I/O (2/4) Section (Main P.C.B. (2/4)) Schematic

Diagram (AV) 51

13.9. A/V I/O (3/4) Section (Main P.C.B. (2/4)) Schematic

Diagram (AV) 52

13.10. A/V I/O (4/4) Section (Main P.C.B. (2/4)) Schematic

Diagram (AV) 53

13.11. Nicam Decoder Section (Main P.C.B. (3/4)) Schematic

Diagram (DE) 55

13.12. Timer (1/4) Section (Main P.C.B. (4/4)) Schematic

Diagram (T) 56

13.13. Timer (2/4) Section (Main P.C.B. (4/4)) Schematic

Diagram (T) 57

13.14. Timer (3/4) Section (Main P.C.B. (4/4)) Schematic

Diagram (T) 58

13.15. Timer (4/4) Section (Main P.C.B. (4/4)) Schematic

Diagram (T) 59

13.16. Tuner Pack Schematic Diagram 60

13.17. Front (L) Schematic Diagram 61

13.18. DV Jack Schematic Diagram 61

14 Printed Circuit Board 63

14.1. Power P.C.B. 63

14.2. Main P.C.B. 64

14.3. Tuner P.C.B. and DV Jack P.C.B. 69

14.4. Front (L) P.C.B. 70

15 Appendix for Schematic Diagram 71

15.1. Voltage and Waveform Chart 71

16 Parts and Exploded Views 78

16.1. Exploded Views 78

16.2. Replacement Parts List 80

CONTENTS

Page Page

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

1.1.1. Leakage current cold check

1.Unplug the AC cord and connect a jumper between the two

prongs on the plug.

2.Measure the resistance value, with an ohmmeter, between

the jumpered AC plug and each exposed metallic cabinet

part on the equipment such as screwheads, connectors,

control shafts, etc. When the exposed metallic part has a

return path to the chassis, the reading should be between

1MWand 5.2MW.

When the exposed metal does not have a return path to the

chassis, the reading must be .

Figure 1

1.1.2. Leakage current hot check

(See Figure 1 .)

1.Plug the AC cord directly into the AC outlet. Do not use an

isolation transformer for this check.

2.Connect a 1.5kW, 10 watts resistor, in parallel with a 0.15µF

capacitors, between each exposed metallic part on the set

and a good earth ground such as a water pipe, as shown in

Figure 1.

3.Use an AC voltmeter, with 1000 ohms/volt or more

sensitivity, to measure the potential across the resistor.

4.Check each exposed metallic part, and measure the

voltage at each point.

5.Reverse the AC plug in the AC outlet and repeat each of the

above measurements.

6.The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliampere. In case a

measurement is outside of the limits specified, there is a

possibility of a shock hazard, and the equipment should be

repaired and rechecked before it is returned to the

customer.

1 Safety Precaution

1.1. General guidelines

1.When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

2.After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

3.After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

2 Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive

(ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistor-sand

semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4.Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable

conductive material).

7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8.Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage

an ES device).

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

2.2. Precaution of Laser Diode

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

2.3. Service caution based on legal restrictions

2.3.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this

equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin

(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that

of the normal solder.

Definition of PCB Lead Free Solder being used

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.

(See right figure)

Service caution for repair work using Lead Free Solder (PbF)

· ·

· The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

· ·

· To put lead free solder, it should be well molten and mixed with the original lead free solder.

· ·

· Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

· ·

· Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt

the lead free solder.

· ·

· Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30

degrees C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

· ·

· The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01K-----------(0.3mm 100g Reel)

RFKZ06D01K-----------(0.6mm 100g Reel)

RFKZ10D01K-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

3 Service Navigation

3.1. Service Information

3.2. Caution for DivX

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

4 Specifications

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

5.1.2. Operating Instructions about DivX

Video-on-Demand Content

DivX Video-on-Demand (VOD) content is encrypted for

unit, you first need to register the unit.

Follow the on line instructions for purchasing DivX VOD content

to enter unit´s registration code and register unit. Visit

www.divx.com/vod for more information.

Display unit´s registration code.

5 New Feature

5.1. About DivX

5.1.1. General

DivX is a new video compressing format that is applied MPEG4 technology to improve image quality and the compressibility, and

it is developed by the DivXNetworks, Inc., Video file of high resolution and the high picture quality can be made though it is a high

compressibility.

DivX codec is necessary for converting video to DivX file and .playback files made.

DMR-ES15EE / DMR-ES15GC / DMR-ES15GCS / DMR-ES15GN / DMR-ES15GCA

Andere Handbücher für DMR-ES15EE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic DVD-Recorder Handbücher

Panasonic

Panasonic Diga DMR-ES20DEB Bedienungsanleitung

Panasonic

Panasonic DMREA38V - DVD RECORDER - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic Diga DMR-E50 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-ES10 Bedienungsanleitung

Panasonic

Panasonic WJ-NV200VK Bedienungsanleitung

Panasonic

Panasonic DMR-EZ48K Bedienungsanleitung

Panasonic

Panasonic DMR-ES18 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EX75EB Bedienungsanleitung

Panasonic

Panasonic DMR-ES35VGN Bedienungsanleitung

Panasonic

Panasonic DIGA DMR-XS350EB Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EZ28EB Bedienungsanleitung

Panasonic

Panasonic DMR-EX75 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EX97 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EX89 Bedienungsanleitung

Panasonic

Panasonic DMR-EX97C Bedienungsanleitung

Panasonic

Panasonic DMR-EX75 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EZ48VEB Bedienungsanleitung

Panasonic

Panasonic DMR-EH57EC Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EZ48V Bedienungsanleitung

Panasonic

Panasonic DMR-XW440 Bedienungsanleitung

Panasonic

Panasonic DMR-EZ49VEB Bedienungsanleitung

Panasonic

Panasonic DIGA DMR-ES15 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-ES20 Bedienungsanleitung

Panasonic

Panasonic DMR-EH50EB Bedienungsanleitung

Beliebte DVD-Recorder Handbücher anderer Marken

Pioneer

Pioneer DVR-65H-S Einrichtungshandbuch

Sony

Sony RDR-VX525 - DVDr/ VCR Combo Bedienungsanleitung

Daewoo

Daewoo DHD-4000D Bedienungsanleitung

Medion

Medion MD 40570 Bedienungsanleitung

Philips

Philips ShowView DVDR3460H Bedienungsanleitung

Sony

Sony RDR-GX355 - Tunerless DVD Recorder Bedienungsanleitung

Sony

Sony DVDirect VRD-MC3 Bedienungsanleitung

Samsung

Samsung DVD-R130/XAA Bedienungsanleitung

FUNAI

FUNAI HD-B2735 Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Technisches Handbuch

Sanyo

Sanyo DRW-1000 Bedienungsanleitung

Philips

Philips DVDR610/05 Bedienungsanleitung

JVC

JVC DR-M10 Bedienungsanleitung

Samsung

Samsung SV-DVD40 Bedienungsanleitung

Philips

Philips DVDR3355 Bedienungsanleitung

FUNAI

FUNAI FDR-90E Bedienungsanleitung

LG RC298 Bedienungsanleitung

Samsung

Samsung DVD-R130 Bedienungsanleitung