Panasonic DMRES10P Bedienungsanleitung

rights reserved. Unauthorized copying and

distribution is a violation of law.

DMR-ES10P

DMR-ES10PC

Vol. 1

Colour

(K).......................Black Type

(S).......................Silver Type

DVD Video Recorder

ORDER NO.DSD0502037C1

B24

DMR-ES10P / DMR-ES10PC

1 Safety precautions 4

1.1. General guidelines 4

1.2. Caution for fuse replacement 4

2 Prevention of Electrostatic Discharge (ESD) to Electrostatic

Sensitive (ES) Devices 5

3 Precaution of Laser Diode 6

4 Handling the Lead-free Solder 6

4.1. About lead free solder (PbF) 6

5 Each Button 7

6 New Feature 8

6.1. Quick start function(REC) 8

7 Taking out the Disc from RAM-Drive Unit when the Disc

cannot be ejected by OPEN/CLOSE button 9

7.1. Forcible Disc Eject 9

7.2. When the Forcible Disc Eject can not be done. 9

8 Service Explorer 10

9 Self-Diagnosis and Special Mode Setting 13

9.1. Self-Diagnosis Functions 13

9.2. Special Modes Setting 14

9.3. Service Modes 16

10 Assembling and Disassembling 19

10.1. Disassembly Flow Chart 19

10.2. P.C.B. Positions 19

10.3. Top Cover 20

10.4. Front Panel 20

10.5. Digital P.C.B. 20

10.6. DVD-RAM Drive 21

10.7. Power P.C.B. 21

10.8. Rear Panel 21

10.9. Front (L) P.C.B. 22

10.10. Main P.C.B. 22

11 Service Fixture and Tools 23

12 Service Positions 23

12.1. Checking and Repairing of Power P.C.B. 23

12.2. Checking and Repairing of Digital P.C.B. 24

12.3. Checking and Repairing of Main P.C.B. 25

12.4. Checking and Repairing of DVD-RAM Drive 26

13 Caution after replacing parts 27

13.1. After replacing the RAM Drive with new one 27

13.2. When the unit does not operate normally after replacing

the Timer Microprocessor or Main P.C.B. 27

14 Standard Inspection Specifications after Making Repairs 27

15 Voltage and Waveform Chart 28

15.1. Power P.C.B. 28

15.2. Main P.C.B. 28

15.3. Tuner P.C.B. 30

15.4. P9001 Connector 30

15.5. Waveform Chart 31

16 Abbreviations 32

17 Block Diagram 35

17.1. Power Supply Block Diagram 35

17.2. Analog Video Block Diagram 37

17.3. Analog Audio Block Diagram 38

17.4. Analog Timer Block Diagram 39

18 Schematic Diagram 41

18.1. Interconnection Schematic Diagram 41

18.2. Main Power Supply Schematic Diagram 42

18.3. Sub Power Section (Main P.C.B. (1/5)) Schematic

Diagram (P) 43

18.4. Main Net Section (Main P.C.B. (2/5)) Schematic Diagram

(M) 44

18.5. Video I/O Section (Main P.C.B. (3/5)) Schematic Diagram

(V) 45

18.6. Audio Main Section (Main P.C.B. (4/5)) Schematic

Diagram (A) 47

18.7. Timer Section (Main P.C.B. (5/5)) Schematic Diagram (T)

18.8. Tuner Pack Schematic Diagram 50

19 Print Circuit Board 51

19.1. Power P.C.B. 51

19.2. Main P.C.B. 52

19.3. Tuner P.C.B., Front (L) P.C.B. 57

20 Exploded Views 59

20.1. Casing Parts & Mechanism Section 59

20.2. Packing & Accessories Section 60

21 Replacement Parts List 61

CONTENTS

Page Page

DMR-ES10P / DMR-ES10PC

1.1.1. Leakage current cold check

1. Unplug the AC cord and connect a jumper between the two

prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between

the jumpered AC plug and each exposed metallic cabinet

part on the equipment such as screwheads, connectors,

control shafts, etc. When the exposed metallic part has a

return path to the chassis, the reading should be between

1MΩand 5.2MΩ.

When the exposed metal does not have a return path to

the chassis, the reading must be .

Figure 1

1.1.2. Leakage current hot check

(See Figure 1 .)

1. Plug the AC cord directly into the AC outlet. Do not use an

isolation transformer for this check.

2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF

capacitors, between each exposed metallic part on the set

and a good earth ground such as a water pipe, as shown in

Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more

sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the

voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the

above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliampere. In case a

measurement is outside of the limits specified, there is a

possibility of a shock hazard, and the equipment should be

repaired and rechecked before it is returned to the

customer.

1 Safety precautions

1.1. General guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.2. Caution for fuse replacement

DMR-ES10P / DMR-ES10PC

2 Prevention of Electrostatic Discharge (ESD) to

Electrostatic Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistor-sand

semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable

conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing

together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage

an ES device).

DMR-ES10P / DMR-ES10PC

3 Precaution of Laser Diode

4 Handling the Lead-free Solder

4.1. About lead free solder (PbF)

Distinction of PbF P.C.B.:

P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B.

Caution:

Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher.

Please use a high temperature soldering iron. In case of the soldering iron with temperature control, please set it to 700 ±

20°F (370 ± 10°C).

Pb free solder will tend to splash when heated too high (about 1100°F/600°C).

When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat

the soldering points with the Pb free solder until it melts enough.

DMR-ES10P / DMR-ES10PC

5 Each Button

DMR-ES10P / DMR-ES10PC

6 New Feature

6.1. Quick start function(REC)

1. General

A few seconds after tuning on the unit,you can start recording to DVD-RAM,HDD.

You can switch the operation of this function (ON/OFF) on the menu screen. .

2. Quick start(REC) principle

In the power-off at Quick start, only power supplies for video IC,tuner and storage media are cut off.

When the REC button is pushed a few second after the power button is pushed, Audio and Video data are stored in

DDR SDRAM before a storage media(DVD-RAM or HDD) preparation.

*Preparation time →DVD-RAM: Fabout 8seconds

After a storage media(DVD-RAM or HDD) preparation,Audio and Video data are transfer from DDR SDRAM to the

storage media.

DMR-ES10P / DMR-ES10PC

7 Taking out the Disc from RAM-Drive Unit when the Disc

cannot be ejected by OPEN/CLOSE button

7.1. Forcible Disc Eject

7.1.1. When the power can be turned off.

1. Turn off the power and press [STOP] [CH UP] keys on the front panel simultaneously for 5 seconds.

7.1.2. When the power can not be turned off.

1. Press [POWER] key on the front panel for over 10 seconds to turn off the power forcibly, and press [STOP] [CH UP] keys on

the front panel simultaneously for 5 seconds.

7.2. When the Forcible Disc Eject can not be done.

1. Turn off the power and pull out AC cord.

2. Remove the Top Case.

3. Remove the Front Panel.

4. Remove 4 screws and Upper Base Unit from DVD-RAM Drive.

5. Take out the disc and put the Opener Roller on fully position for direction of Arrow.

6. Put the Upper Base Unit so that the Opener Roller is inserted into the groove.

7. Check Opener Roller is seen through the Opener position Checking Hole, and tighten 4 screws.

DMR-ES10P / DMR-ES10PC

8 Service Explorer

Confirm “RAM-Drive Last Error” in Service Mode

Execute Service Mode

1. Press [REC], [CH UP] and [OPEN/CLOSE] simultaneously for 5 seconds when P-off.

FL Display:

*After finishing display “(7). Factor of Drive Error occurring”, press [0] [2] ~[1] [9] keys of the Remote Controller so that

19 memories can be displayed as maximum.

2. Press [4] [2] keys of remote controller.

Example of FL Display:

(1) Error Number is displayed for 5 seconds.

(2) Time when the error has occurred is displayed for 5 seconds.

(3) Last Drive Error (1/2) is displayed for 5 seconds.

(4) Last Drive Error (2/2) is displayed for 5 seconds.

DMR-ES10P / DMR-ES10PC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic DVD-Recorder Handbücher

Panasonic

Panasonic DMR-EZ48VP Bedienungsanleitung

Panasonic

Panasonic DMR-EX77EG Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EZ48V Bedienungsanleitung

Panasonic

Panasonic DMR-EX97C Bedienungsanleitung

Panasonic

Panasonic DMR-EH63 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-ES30V Bedienungsanleitung

Panasonic

Panasonic DMR-EX93CEG Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EH57 Bedienungsanleitung

Panasonic

Panasonic DIGA DMR-XS350EB Bedienungsanleitung

Panasonic

Panasonic DMR-EZ45VEB Bedienungsanleitung

Panasonic

Panasonic Diga DMR-ES15EBL Bedienungsanleitung

Panasonic

Panasonic DMR-EH65EC Bedienungsanleitung

Panasonic

Panasonic DMR-EX78EB Bedienungsanleitung

Panasonic

Panasonic DMR-E85HS Gebrauchs- und Pflegehandbuch

Panasonic

Panasonic Diga DMR-EH695 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EX89 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EH50 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EH675 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EH585 Bedienungsanleitung

Panasonic

Panasonic DIGA DMR-XW380 Bedienungsanleitung

Panasonic

Panasonic Diga DMR-EX89EB Bedienungsanleitung

Panasonic

Panasonic DMREA18 - DVD RECORDER - MULTI LANGUAGE Bedienungsanleitung

Panasonic

Panasonic DIGA DMR-E85H Bedienungsanleitung

Panasonic

Panasonic Diga DMR-E75V Bedienungsanleitung

Beliebte DVD-Recorder Handbücher anderer Marken

Pioneer

Pioneer DVR-65H-S Einrichtungshandbuch

Sony

Sony RDR-VX525 - DVDr/ VCR Combo Bedienungsanleitung

Daewoo

Daewoo DHD-4000D Bedienungsanleitung

Medion

Medion MD 40570 Bedienungsanleitung

Philips

Philips ShowView DVDR3460H Bedienungsanleitung

Sony

Sony RDR-GX355 - Tunerless DVD Recorder Bedienungsanleitung

Sony

Sony DVDirect VRD-MC3 Bedienungsanleitung

Samsung

Samsung DVD-R130/XAA Bedienungsanleitung

FUNAI

FUNAI HD-B2735 Bedienungsanleitung

Pioneer

Pioneer PRV-LX1 Technisches Handbuch

Sanyo

Sanyo DRW-1000 Bedienungsanleitung

Philips

Philips DVDR610/05 Bedienungsanleitung

JVC

JVC DR-M10 Bedienungsanleitung

Samsung

Samsung SV-DVD40 Bedienungsanleitung

Philips

Philips DVDR3355 Bedienungsanleitung

FUNAI

FUNAI FDR-90E Bedienungsanleitung

LG RC298 Bedienungsanleitung

Samsung

Samsung DVD-R130 Bedienungsanleitung