Panasonic WJ-PB85A32 Bedienungsanleitung

-1-

■Preface

The WJ-PB85A32 Alarm Input Board is an optional board for expanding the capabilities of the

System 850 Matrix Switcher.

It transmits a received alarm signal to the CPU (Central Processing Unit) via Ethernet to activate

the assigned alarm event.

The board an also be used an as alarm output board by changing the position of internal switch-

es.

■Appearance

qAlarm Input Port (1 - 32)

This port accepts alarm input from the associated alarm sensors through either Normally

Open (N.O) or Normally Closed (N.C) contacts.

1-32

ALARM

Before attempting to connect or install this product,

please read these instructions carefully and save this manual for future use.

Extend Card (Alarm in)

Model No. WJ-PB85A32

Ground

Not used

Alarm 32

Alarm 31

Alarm 30

Alarm 29

Alarm 28

Alarm 27

Alarm 26

Alarm 25

Alarm 24

Alarm 23

Alarm 22

Alarm 21

Alarm 20

Pin No. Designation

Alarm 19

Alarm 18

Alarm 17

Alarm 16

Alarm 15

Alarm 14

Alarm 13

Alarm 12

Alarm 11

Alarm 10

Alarm 9

Alarm 8

Alarm 7

Alarm 6

Alarm 5

Alarm 4

Alarm 3

Alarm 2

Alarm 1

33 15

37 19

Hold this board only by its edges. Otherwise components on the board may be damaged by static electricity.

Caution

-2-

■Board Setting

Before installing this board, the following settings should be made by qualified service personnel or system installers.

SW3 SW7 SW6 SW5 SW4

SW2

SW1SW8

ALARM INPUT BOARD

Reset Switch

1 2 3 4 5 6 7 8

SW4

OFF

CH1 - 8

1 2 3 4

SW3

OFF

H19 1725

816 2432

Board

No. Alarm Input SW Positions

SW2 SW1

1 - 32

33 - 64

65 - 96

97 - 128

129 - 160

161 - 192

193 - 224

225 - 256

257 - 288

289 - 320

321 - 352

353 - 384

385 - 416

417 - 448

449 - 480

481 - 512

1. Set switches (SW1 and SW2) on the board to designate the Alarm Input board number as shown in the following table.

The factory default setting is Board Number 1 (00).

-3-

2. Set switches (SW4, SW5, SW6, and SW7) on the

board to meet the alarm input requirements.

ON: Normally Closed (N.C)

OFF: Normally Open (N.O)

The factory default settings are OFF.

1 2 3 4 5 6 7 8

SW4

OFF

CH1 - 8

■Installation

The following installation should be made by qualified

service personnel or system installers.

●Installing Additional Extension

Boards

1. Remove the screws from the rear panel(s) of the

WJ-SX850 Matrix Switcher Card Cage.

2. Remove the rear panel(s).

3. Remove the front panel of the cage by removing the

two screws on the panel shown below.

3. If this board is used for Alarm Output, set switches

(SW3) on the board as follows.

ON: Output mode

OFF: Input mode

The factory default settings are OFF.

1 2 3 4

SW3

OFF

H1 9 17 25

8 16 24 32

4. Place the Boards into the specified positions in the

front or rear of the Cage by sliding them along the

board guides as shown below.

5. Make sure to push in the Boards until they are seat-

ed firmly.

6. Secure the rear board by tightening the two screws

on the board.

■Specifications

Alarm Input (1 - 32): Normally Open or Normally Closed selectable

37-pin D-sub connector

(Alarm Output): Open Collector Output, 12 V DC 50 mA maximum

Dimensions: Front Board; 255(W) x 250(H) x 12(D) mm

10-1/16”(W) x 9-13/16”(H) x 1/2”(D)

Rear Board; 117.5(W) x 265(H) x 20(D) mm

4-5/8”(W) x 10-7/16”(H) x 13/16”(D)

Weight: 0.5 kg (1.1 lbs)

Weight and dimensions indicated are approximate.

Specifications are subject to change without notice.

NM1099-0 YWV8QA5059AN Printed in Japan

N19

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada (905)624-5010

Panasonic Sales Company

Division of Matsushita Electric of Puerto Rico Inc.

Ave. 65 de Infanteria. Km. 9.5

San Gabriel Industrial Park, Carolina,

Puerto Rico 00985 (809)750-4300

Panasonic Security and Digital Imaging Company

A Division of Matsushita Electric Corporation of America

Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094

Regional Offices:

Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303

Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838

Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211

Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840

7. Close open spaces on the rear of the Cage with the

supplied rear panel(s).

8. Close the front of the cage by fixing the front panel.

Board

Tighten screws

Rear

panel

Rear

panel

Tighten screws

Andere Panasonic Extender Handbücher

Panasonic

Panasonic WJHDE300 - DIGITAL DISK RECORDER Bedienungsanleitung

Panasonic

Panasonic WJHDE510 - EXTENTION BOARD Bedienungsanleitung

Panasonic

Panasonic KX-TGA405 Bedienungsanleitung

Panasonic

Panasonic KX-TGA405 Bedienungsanleitung

Panasonic

Panasonic KX-TGA405 Bedienungsanleitung

Panasonic

Panasonic KX-TGA407 Bedienungsanleitung

Panasonic

Panasonic KX-TGA407B Bedienungsanleitung

Panasonic

Panasonic WJHDE510 - EXTENTION BOARD Bedienungsanleitung

Panasonic

Panasonic SH-WL40 Bedienungsanleitung

Panasonic

Panasonic WV-AD110A Bedienungsanleitung

Panasonic

Panasonic WJHD500 - DIGITAL DISC RECORDE Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung