Panasonic ER1411 Bedienungsanleitung
Operating Instructions
AC/Rechargeable Professional Hair Clipper
Model No. ER1411
Before operating this unit, please read these instructions completely and save
them for future use.
ER1411_AUS_JABARA.indd 1 2010/06/02 20:00:01
2
Thank you for choosing a Panasonic Hair Clipper. Please read all
instructions before use.
Important
Before use
This clipper is designed for professional use to trim hair and beards. Charge it
for 8 hours before use for the first time in order to activate the built‑in
rechargeable batteries. It can be operated on either an AC adaptor or
rechargeable batteries. Read all instructions carefully before use.
Charging the clipper
Do not use any power cord or AC adaptor other than this AC adaptor
(RE9‑41).
Avoid charging the batteries at temperatures below 5 °C or above 35 °C.
Avoid charging the batteries in direct sunlight or near a radiating heat source.
The charge status ( ) lamp may blink at an early stage when it is used for
the first time or if it has not been used for 6 or more months even if it is fully
charged. This is not a malfunction.
Even though the clipper may not be used for an extended period, charge
every 6 months to preserve battery life.
The power cord cannot be replaced. If it is damaged, the AC adaptor should
be discarded.
Using the clipper
This clipper has a built‑in rechargeable battery. Do not throw into fire, apply
heat, or charge, use, or leave in a high temperature environment.
Warning ‑ Keep the appliance dry.
The clipper may become warm during operation and/or charging. This is
normal.
Check that the blades and the attachments are not damaged before use.
Replace them if they are damaged.
Before each use, apply oil at the places marked with arrows. (See page 6.)
You should not allow permanent wave lotion, hair restorer or hair spray to
come into contact with the main body or the blades.
Doing so may result in cracking, discoloring or corrosion.
You should not drop the clipper on the floor.
You should not knock the blades and the attachments against hard objects.
You should not trim the hair of a pet.
Cleaning the clipper
Clean the housing using only a cloth slightly dampened with water or a mild
soap solution.
Never use a caustic solution.
Never submerge the clipper in water.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ER1411_AUS_JABARA.indd 2 2010/06/02 20:00:01
3
Storing the clipper
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
Never tamper with moving parts.
Do not wrap the appliance by the cord, as it may become detached causing
damage or injury.
If the clipper is not working properly, have it inspected at an authorized
service center.
Specifications
Power source: See the name plate on the product.
(Automatic voltage conversion)
Motor voltage: 2.4 V DC
Charging time: 1 hour
Parts identification
3
mm
6
mm
9
mm
12
mm
15
mm
18
mm
AMain body
1Power switch [0·CHARGE/1]
2Charge status ( ) lamp
3Appliance socket
BBlade
4Mounting hook
5Cleaning lever
6Moving blade
7Stationary blade
C3 mm/6 mm comb attachment
D9 mm/12 mm comb attachment
E15 mm/18 mm comb attachment
FAC adaptor (RE9‑41)
8Power cord
9Appliance plug
GCleaning brush
HOil
•
•
•
•
ER1411_AUS_JABARA.indd 3 2010/06/02 20:00:02
4
Charging the hair clipper
Charge
1
1Slide the power switch to
“0·CHARGE”.
2
2Plug in the AC adaptor into a
household outlet.
3
3Insert the appliance plug into the
clipper.
Charge status ( ) lamp glows in red and charging starts.
Charging is completed when Charge status ( ) lamp blinks in red
once every second. (Max. 1 hour later)
10 minutes after charging is completed, the charge status
( ) lamp blinks in red once every 2 seconds.
1 full charge will provide approximately 80 minutes of continuous
operation.
AC operation
If you connect the AC adaptor to the clipper in the same way as for charging,
and turn on the power, you can use it even if the battery capacity is low.
If the clipper does not operate, charge the clipper for approximately
1 minute.
Be careful not to discharge the battery completely with the power left turned
on. It results in shortening the battery life.
•
•
•
•
•
•
ER1411_AUS_JABARA.indd 4 2010/06/02 20:00:02
5
Using the hair clipper
Cut
Using the comb attachments
1
1Select the trimming heights indicated on
the insides and sides of the attachments.
2
2Mount the attachment to the clipper as
illustrated.
The actual cut length may be longer than the set
length.
Removing the attachment from the clipper
Slide one side of the attachment off the mounting in
direction indicated with the arrow.
Blade maintenance
Care
Removing and mounting the blade
Removing the blade
1. Hold the clipper with the power switch
facing upward and push the blade with
your thumb while catching the blade in
your other hand.
Be sure to turn off the power before you
remove the blade.
•
ER1411_AUS_JABARA.indd 5 2010/06/02 20:00:02
6
Mounting the blade
1. Fit the mounting hook into the blade
mounting on the clipper and push in
until it clicks.
Cleaning the blade
1. Brush off any
hairs from the
clipper and from
around the blade.
2. Remove the blade
and brush off the
hairs from the
blade edge.
3. Brush the hairs out
from between the
stationary blade and
the moving blade while
pressing down on the
cleaning lever to raise
the moving blade.
Lubrication
1. Apply a few drops of the oil to the space
between the stationary blade and moving
blade.
Apply the oil to the clipper before and after
each use.
2. Remount the blade on the clipper.
•
ER1411_AUS_JABARA.indd 6 2010/06/02 20:00:02
7
Removing the built‑in rechargeable batteries
Remove the batteries as illustrated.
Disconnect the clipper from a household outlet.
Fully discharge the batteries.
Be careful not to short‑circuit the batteries.
WARNING ‑ Do not attempt to replace the batteries for the purpose of
reusing the clipper. This could result in the risk of fire or electric shock.
Important notice regarding environmental protection
The built‑in rechargeable Nickel‑Metal Hydride batteries contain substances
that may be environmentally harmful. Please remove the batteries before
discarding your clipper.
For environmental protection and recycling materials
This clipper contains Nickel‑Metal Hydride batteries.
Please make sure that the batteries are disposed of at an officially assigned
location, if there is one in your country.
•
•
•
ER1411_AUS_JABARA.indd 7 2010/06/02 20:00:02
FEN
Printed in China
0000000000 X0000‑0
Panasonic Electric Works Wanbao (Guangzhou) Co., Ltd.
http://panasonic.net
ER1411_AUS_JABARA.indd 8 2010/06/02 20:00:02
Inhaltsverzeichnis
Andere Panasonic Haarschneider Handbücher
Panasonic
Panasonic ER-HGP72 Bedienungsanleitung
Panasonic
Panasonic ER-GP22 Bedienungsanleitung
Panasonic
Panasonic ER1510 Bedienungsanleitung
Panasonic
Panasonic ER508 Bedienungsanleitung
Panasonic
Panasonic ER-SC60 Bedienungsanleitung
Panasonic
Panasonic ER?GC20 Bedienungsanleitung
Panasonic
Panasonic ER-GC52 Bedienungsanleitung
Panasonic
Panasonic ER1611 Bedienungsanleitung
Panasonic
Panasonic ER131 Bedienungsanleitung
Panasonic
Panasonic ER1512 Bedienungsanleitung
Panasonic
Panasonic ER-GC51 Bedienungsanleitung
Panasonic
Panasonic ER-FGP72 Bedienungsanleitung
Panasonic
Panasonic ER-SC60 Bedienungsanleitung
Panasonic
Panasonic ER-206 Bedienungsanleitung
Panasonic
Panasonic ER1512 Bedienungsanleitung
Panasonic
Panasonic ER-GC70 Bedienungsanleitung
Panasonic
Panasonic ER?GC20 Bedienungsanleitung
Panasonic
Panasonic ER-GC30 Bedienungsanleitung
Panasonic
Panasonic ER5209 Bedienungsanleitung
Panasonic
Panasonic ER-GP80 Bedienungsanleitung
