Panasonic Viera TC-L65WT600 Bedienungsanleitung

Unauthorized copying and distribution is a violation

of law.

ORDER NO.MTNC130957CE

B32 Canada: B61

65 inch Class 4K Ultra HD TV

Model No. TC-L65WT600

LA46 Chassis

TABLE OF CONTENTS PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3

2Warning--------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------4

2.2. About lead free solder (PbF) ----------------------------5

3 Service Navigation------------------------------------------------6

3.1. PCB Layout--------------------------------------------------6

4 Specifications ------------------------------------------------------7

5 Technical Descriptions------------------------------------------8

5.1. Specification of KEY for DTCP-IP, WMDRM

and Widevine------------------------------------------------8

6 Service Mode-------------------------------------------------------9

6.1. How to enter into Service Mode------------------------9

6.2. SRV-TOOL-------------------------------------------------10

6.3. Hotel mode------------------------------------------------- 11

6.4. Data Copy by USB Memory---------------------------12

7 Troubleshooting Guide----------------------------------------15

7.1. Check of the IIC bus lines------------------------------15

7.2. Power LED Blinking timing chart---------------------16

7.3. LCD Panel test mode -----------------------------------16

8 Disassembly and Assembly Instructions---------------17

8.1. Disassembly Flow Chart for the Unit----------------17

8.2. Disassembly Procedure for the Unit-----------------18

9 Measurements and Adjustments --------------------------42

9.1. Voltage chart of P-board--------------------------------42

9.2. Voltage chart of A-board-------------------------------42

9.3. Voltage chart of TC-board-----------------------------42

10 Block Diagram ---------------------------------------------------43

10.1. Main Block Diagram-------------------------------------43

10.2. Block (1/2) Diagram -------------------------------------44

10.3. Block (2/2) Diagram -------------------------------------45

11 Wiring Connection Diagram---------------------------------46

11.1. Caution statement.---------------------------------------46

11.2. Wiring 1-----------------------------------------------------46

11.3. Wiring 2-----------------------------------------------------47

11.4. Wiring 3-----------------------------------------------------49

11.5. Wiring 4-----------------------------------------------------48

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

4. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

5. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the

wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.

6. When conducting repairs and servicing, do not twist the Fasten connectors but plug them straight in or unplug them straight

out.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed

metallic cabinet part on the equipment such as

screwheads, connectors, control shafts, etc. When the

exposed metallic part has a return path to the chassis, the

reading should be 100 Mohm and over.

When the exposed metal does not have a return path to

the chassis, the reading must be .

1.1.2. Leakage Current Hot Check (See

Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5kohm, 10 watts resistor, in parallel with a

0.15F capacitors, between each exposed metallic part

on the set and a good earth ground such as a water pipe,

as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more

sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the

voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliamp. In case a

measurement is outside of the limits specified, there is a

possibility of a shock hazard, and the equipment should

be repaired and rechecked before it is returned to the

customer.

Figure 1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES)Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or

comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)

sufficient to damage an ES device).

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it's manufacture due to environmental conservation issues. For service and repair work, we'd

suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 F (30~40 C) higher. Please

use a high temperature soldering iron and set it to 700 ± 20 F (370 ± 10 C).

• Pb free solder will tend to splash when heated too high (about 1100 F or 600 C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb

solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the

opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.

However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

3 Service Navigation

3.1. PCB Layout

Board Name Function

A-Board Tuner, OFDM, ADV, LD4, STBY EEP

K-Board IR/LED/AI

P-Board Power Supply

GK-Board SW

FR-Board GCX

LL-Board Lighting (Left)

LR-Board Lighting (Right)

LA-Board Lighting (Left add)

LB-Board Lighting (Right add)

4 Specifications

■Built-in Camera

■Wireless LAN

■Bluetooth

■3D Eyewear

Note

Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.

3D Eyewear and VIERA Touch Pad Controller use Bluetooth wireless technology.

Power Source AC 110-127 V, 60 Hz

Power Consumption

Rated Power 282 W

Standby Power 0.2 W

Display Panel

Panel System LCD panel (LED backlight)

Screen size 65 inch class (64.5 inches measured diagonally)

W x H x Diagonal 56.2 inch x 31.6 inch x 64.5 inch (1,428 mm x 804 mm x 1,639 mm)

Number of pixels 3840 x 2160

Speaker Output 18 W [4 W + 4 W + 10 W] ( 10 % THD )

Channel Capability (Digital/Analog) VHF/ UHF: 2 - 69, CATV: 1 - 135

Operating Conditions Temperature: 32 F - 95 F (0 C - 35C)

Humidity: 20 % - 80 % RH (non-condensing)

Connection Terminals

VIDEO IN RCA PIN (VIDEO, AUDIO-L, AUDIO-R)

COMPONENT IN RCA PIN (Y, PB, PR, AUDIO-L, AUDIO-R)

HDMI IN 1/2/3/4 TYPE A Connector (supports [HDAVI Control 5] function)

USB 1/2/3 USB1/2: Type A connector DC 5V, Max. 500mA [Hi-Speed USB (USB 2.0)]

USB3: Type A connector DC 5V, Max. 900mA [SuperSpeed USB (USB 3.0)]

DisplayPort VESA DisplayPort (applicable to 4K format)

DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber Optic

OTHERS SD CARD slot, ETHERNET (10BASE-T/100BASE-TX)

Dimensions (W x H x D)

Including pedestal 57.8 inch x 37.8 inch x 16.8 inch (1,468 mm x 960 mm x 425 mm)

TV Set only 57.8 inch x 34.0 inch x 2.2 inch (1,468 mm x 863 mm x 56 mm)

Mass Including pedestal 94.8 lb. (43.0 kg) NET

TV Set only 83.8 lb. (38.0 kg) NET

Lens F2.0 Lens; FOV (D) 50.9° (in HD mode)

Focus Fixed focus

Resolution 1280 x 720

Standard Compliance and

Frequency Range*1,*2IEEE 802.11a/n : 5.15 Ghz - 5.35 Ghz, 5.47 GHz - 5.85 Ghz

IEEE 802.11b/g/n : 2.400 Ghz - 2.4835 GHz

Security WPA2-PSK (TKIP/AES), WPA-PSK (TKIP/AES), WEP (64bit/128bit)

*1The frequency and channel differ depending on the country.

*2802.11b/g/n CH1 ~ CH11 only use for United States and Canada.

Standard Compliance Bluetooth 3.0

Frequency Range 2.402GHz - 2.480 GHz

Battery Coin-shaped lithium battery CR2025

Operation time: Approx. 75 hours in continuos use of the battery made by Panasonic

5 Technical Descriptions

5.1. Specification of KEY for DTCP-IP, WMDRM and Widevine

5.1.1. General information:

1. NAND Flash (IC8900) for spare parts has the seed of KEY for each DTCP-IP for DLNA, WMDRM for Netflix and Widevine for

CinemaNow.

2. The final KEY data will be generated by Main IC (IC8000) when SELF CHECK was done and are stored in both Main IC

(IC8000) and NAND Flash (IC8900).

5.1.2. Replacement of ICs:

When Main IC is replaced, NAND Flash should be also replaced with new one the same time.

When NAND Flash is replaced, Main IC is not necessary to be replaced the same time.

After the replacement of IC, SELF CHECK should be done to generate the final KEY data.

How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for

more than 3 seconds.

TV will be forced to the factory shipment setting after this SELF CHECK.

6 Service Mode

6.1. How to enter into Service Mode

6.1.1. Purpose/

After exchange parts, check and adjust the contents of adjustment mode.

While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.

Note:

Service Mode can not be entered when 3D signal input.

Input 2D signal to enter Service Mode.

6.1.2. Key command

[1] button...Main items Selection in forward direction

[2] button...Main items Selection in reverse direction

[3] button...Sub items Selection in forward direction

[4] button...Sub items Selection in reverse direction

[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )

6.1.3. How to exit

Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.

6.1.4. Contents of adjustment mode

• Value is shown as a hexadecimal number.

• Preset value differs depending on models.

• After entering the adjustment mode, take note of the value in each item before starting adjustment.

Main item Sub item Sample Data Remark

ADJUST CONTRAST 000

COLOR 3A

TINT 00

SUB-BRT 800

BACKLGT FFF

B-Y-G 40

R-Y-A 00

V COM 000

WB-ADJ R-GAIN 80

G-GAIN 76

B-GAIN 59

R-CENT 82

G-CENT 80

B-CENT 6D

OPTION Boot ROM Factory Preset.

STBY-SET 00

EMERGENCY ON

CLK MODE 01

CLOCK FFF

EDID-CLK HIGH

SRV-TOOL 00 See next.

6.2. SRV-TOOL

6.2.1. How to access

1. Select [SRV-TOOL] in Service Mode.

2. Press [OK] button on the remote control.

6.2.2. Display of SOS History

SOS History (Number of LED blinking) indication.

From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.

This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory

shipment setting].

6.2.3. POWER ON TIME/COUNT

Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3 sec.

Time : Cumulative power on time, indicated hour : minute by decimal

Count : Number of ON times by decimal

Note : This indication will not be cleared by either of the self-checks or any other command.

6.2.4. Exit

Disconnect the AC cord from wall outlet or press the [POWER] button on the main unit for 3 seconds to turn off and then turn on

automatically.

Andere Handbücher für Viera TC-L65WT600

Inhaltsverzeichnis

Andere Panasonic HDTV Handbücher

Panasonic

Panasonic TC-55EZ950C Bedienungsanleitung

Panasonic

Panasonic PT52LCX15B - MULTI MEDIA DISP Bedienungsanleitung

Panasonic

Panasonic TC-P42G10 Bedienungsanleitung

Panasonic

Panasonic VIERA TC-P54G20 Bedienungsanleitung

Panasonic

Panasonic TC-65FZ1000C Montageanleitung

Panasonic

Panasonic TC-L37G1 Bedienungsanleitung

Panasonic

Panasonic PT47WX54 - 47" PROJECTION TV Bedienungsanleitung

Panasonic

Panasonic PT47WX52F - 47" PROJECTION TV HD Bedienungsanleitung

Panasonic

Panasonic VIERA TH-42PZ85U Bedienungsanleitung

Panasonic

Panasonic TH-C50HD18 Bedienungsanleitung

Panasonic

Panasonic P54V10 - TC - 54.1" Plasma TV Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42X3L Bedienungsanleitung

Panasonic

Panasonic Viera TC-L42E60 Bedienungsanleitung

Panasonic

Panasonic TH-55LRU50 Bedienungsanleitung

Panasonic

Panasonic VIERA TC-58DX800C Bedienungsanleitung

Panasonic

Panasonic PT-56LCX70 - 56" Rear Projection TV Bedienungsanleitung

Panasonic

Panasonic TC-65EZ1000C Montageanleitung

Panasonic

Panasonic LIFI PT-50LCZT0 Bedienungsanleitung

Panasonic

Panasonic Viera TC-L50ET60 Bedienungsanleitung

Panasonic

Panasonic TH-32LRH30U Bedienungsanleitung

Panasonic

Panasonic TC-P42XT50L Gebrauchsanweisung

Panasonic

Panasonic Viera TC-L50ET60 Bedienungsanleitung

Panasonic

Panasonic Viera TC-P54Z1 Bedienungsanleitung

Panasonic

Panasonic Viera TC-26LX85 Bedienungsanleitung

Beliebte HDTV Handbücher anderer Marken

Vizio

Vizio M602i-B3 Bedienungsanleitung

JVC

JVC LT-40C750 Bedienungsanleitung

Pendo

Pendo PNDLFHU55 Bedienungsanleitung

RCA

RCA RTU7575-B Bedienungsanleitung

Sharp

Sharp LC60LE830UN Bedienungsanleitung

LEECO

LEECO uMax85 Bedienungsanleitung

LG 50PC1DRA Bedienungsanleitung

Samsung

Samsung Tantus HCJ555W Bedienungsanleitung

Sceptre

Sceptre X23 Bedienungsanleitung

Medion

Medion LIFE P13901 Bedienungsanleitung

Vizio

Vizio D32h-C0 Bedienungsanleitung

JVC

JVC EM39T Bedienungsanleitung

Sceptre

Sceptre X460BV-FHD Bedienungsanleitung

BEA

BEA 49B4KUHD Bedienungsanleitung

EQD

EQD Auria EQ3288 Bedienungsanleitung

JVC

JVC LT-24C660 Bedienungsanleitung

RCA

RCA Scenium D32TF20 Bedienungsanleitung

LG M3702C Bedienungsanleitung