Panasonic SC-HT1500 Bedienungsanleitung

STEP 1Front speaker assembly

∑ Front speaker units ∑ Pipes ∑ Large bases ∑ Washer screws

Supplied Accessories

Make sure you have all

the indicated components

before assembly, setup,

and connection.

Preparation

≥

To prevent damage or scratches, lay a soft cloth and perform assembly on it.

≥ For assembly, use a Phillips-head screwdriver.

1Attach the pipe to the large base.

2Attach the stand to the front speaker.

≥There is no difference between the right and left speakers and stands.

≥Using the polyfoam and packaging cover included with this unit may be

convenient.

1Remove the mounting plate screw, and remove plate B.

2Place the pipe on plate A and attach plate B.

Rotate the pipe so that the ﬂat side is facing away from the back of the

speaker.

3Secure the plate with the same screw removed in

procedure 1.

Thread the speaker

cable through here.

Groove

Lessen excess speaker cable.

2Insert the pipe.

Insert the pipe while slightly

pulling on the speaker cable.

Washer screw

Cable

Rear side of base

The supplied stands are specially designed for

attachment to Panasonic SB-FS1500 front speakers.

Only use as indicated in this setup.

Cable Hole for screw

1Thread the speaker cable through the base. 3Secure the pipe to the base.

Ensure the screws are securely fastened.

Fit the offset into the slot

and slide the plate B into the

locked position.

Plate B

Mounting plate screw

Speaker

Packaging cover

Polyfoam

Plate A

Plate B

Pipe

Offset

Slot

Align the surface of

plate B so that it is even

with the pipe surface.

SC-HT1500(P,PC)04.6.39:07AMページ1

1122.5 mm

(443/16q)

Stopper screw

Do not remove.

Speaker

Pipe

Base

∫Front speaker height (Assembled diagram)

715.5 mm

(285/32q)

You can adjust within this range.

For your reference

You can enjoy good acoustics by adjusting the

height of the speaker with the height of the

television so the center position of both are

approximately the same.

Press the speaker cable into the groove.

r:Copper

s:Silver

Be careful not to loosen the screw too

much or the speaker may detach and fall.

4Adjust the speaker height.

≥Check the screws you tightened in procedures 1–3 and 2–3if the pipe and speaker are loose. (➜page 2)

1Loosen the attached mounting plate

screw until the attached speaker is

slightly loose and adjustable.

2With one hand on the base, and the

other holding the speaker, adjust the

height of the speaker up and down.

3 Connect the speaker cables.

Push !

1Press the speaker cable and thread between

the hooks.

Cable

∫For rear side of speaker

Stopper screw

Screw to stop mounting plate from moving or sliding

below this point.

∫For rear side of base

If there is any excess

speaker cable, thread the

speaker cable from the

opening near the top of the

pipe while lightly pulling the

speaker cable from the

bottom of the base.

Phillips-head screwdriver

5Fasten the speaker cable.

2Fit the speaker cable into the base

cover groove as far as possible.

Connect the speaker cables.

≥Twist off the vinyl ends of the speaker cables.

3Tighten the mounting plate screw

securely.

≥Using the same polyfoam as done in procedure 2 will assist you in safely and securely fastening the speaker cables.

Rear side of speaker

SC-HT1500(P,PC)04.6.39:07AMページ2

STEP 2Surround speaker assembly

∑ Surround speaker units ∑ Small bases ∑ Long screws

∑ Surround speaker cables

[10 m (33 feet) cable]

Press the speaker cable into the groove.

r:Copper

s:Silver

2 Connect the speaker cables.

Push !

1Press the speaker cable

and thread between the

hooks.

Cable

3Fasten the speaker cable.

2Fit the speaker cable into the

base cover groove as far as

possible.

Connect the speaker cables.

≥Twist off the vinyl ends of the speaker cables.

The supplied stands are specially designed for

attachment to Panasonic SB-PS1500 surround speakers.

Only use as indicated in this setup.

1Attach the surround speaker to the small base.

Thread the speaker

cable through here.

Cable Rear side of base

Rear side of base

Approx.

350 mm (1325/32q)

Cable

≥There is no difference between the right and left speakers and bases.

1Thread the speaker cable through the base and mount the

speaker on it.

2Secure the speaker to the base.

Ensure the screws are securely fastened

by lightly tightening the two screws

alternately until fully tightened.

Long screws

If there is any excess speaker cable, pull lightly

on the speaker cable from the bottom of the base

to eliminate the excess, and press the speaker

cable into the groove.

∫For rear side of speaker

∫For rear side of base

Rear side of speaker

SC-HT1500(P,PC)04.6.39:07AMページ3

Other speaker setup options

Attaching to a wall

[Note]

≥The wall or pillar on which the speakers are to be attached should be capable of supporting 10 kg(22 Ib.) per screw.

Consult a qualiﬁed building contractor when attaching the speakers to wall. Improper attachment may result in damage to the wall and

speakers.

≥When mounting the front and surround speakers to a wall, we recommend using a string (not included) to prevent it from a fall (➜ below).

≥Use of optional speaker cables are recommended for wall mounted front speakers. (You can also remove the speaker cables from the pipes

supplied with this system).

≥Two screws are needed per speaker when attaching the speakers

to the wall.

Center speaker

Vertical

240 mm

(97/16q)

Vertical

142 mm

(519/32q)

Vertical

27 mm (11/16q)

Vertical

340 mm (133/8q)

Vertical

84 mm (35/16q)

Horizontal

185 mm (79/32q)

Front speakers Surround speakers

30–35 mm (13/16q–13/8q)

Wall or pillar

‰7.5–9.4 mm (19/64q–3/8q)

8–11 mm (3/8q–7/16q)

1Drive a screw (not included) into the wall. 2Fit the speaker securely onto the screw(s)

with the hole(s).

Surround speakers

Center speaker

Front speakers

Move the speaker so the screw is in this

position.

In this position, the speaker will likely fall if

moved to the left or right.

∫Preventing the speakers from falling over

Preparation

Attach screw eyes (not included) to secure the speakers to a wall

(➜ diagram on the right).

≥You will need to obtain the appropriate screw eyes to match the walls

and pillars to which the screw eyes are going to be fastened.

≥Consult a qualiﬁed housing contractor concerning the appropriate

procedure when attaching to a concrete wall or a surface that may not

have strong enough support. Improper attachment may result in damage

to the wall or speakers.

1Thread the string (not included) through the slot on the

rear of the front and surround speakers to prevent it from

falling over.

2Loop the string through the screw eye and tie tightly.

String (not included)

Approx. 150 mm (529/32q)

Wall

Screw eye (not included)

Rear of the front speaker

e.g. Front speaker

SC-HT1500(P,PC)04.6.39:07AMページ4

STEP 3Setup and connection of speakers

Center speaker

≥Vibration caused by the center speaker can

disrupt the picture if it is placed directly on the

television.

Put the center speaker on a rack or shelf.

≥To prevent the speakers from falling do not

place the speakers directly on top of the

television. Surround speakers

Front speakers

Main unit

[Note]

Keep your speakers at least

10 mm (13/32q) away from the

system for proper ventilation.

(L)

(R)

Preparation

Check to make sure the washer screws on the bottom of the front

speaker bases are not loose.

Place the front, center, and surround speakers at approximately

the same distance from the seating position.

The angles in the diagram are approximate.

Positioning for best effect

How you set up your speakers can affect the bass and the sound ﬁeld.

Note the following points.

≥Place speakers on ﬂat secure bases.

≥Placing speakers too close to ﬂoors, walls, and corners can result in

excessive bass. Cover walls and windows with a thick curtain.

[Note]

≥The left and right speaker pairs are the same with respect to the front

and surround speakers. Place each of the speakers in accordance with

the stickers you just attached.

≥Before moving the main unit, ensure the disc tray is empty.

Failure to do so will risk severely damaging the disc and the main unit.

Subwoofer

Place to the right or left of the television

on the ﬂoor so that it won’t cause

vibration.

Leave 10 cm (4q) at the rear for

ventilation.

You can enjoy more effective

surround effects by placing the

surround speakers on shelves at

approximately the same height as

the front speakers.

1Place the speakers.

(R)

(L)

∑ Center speaker

∑ Sheet of speaker-cable

stickers

∑ Front speakers ∑ Surround speakers

∑ Center speaker cable

[4 m (13 feet) cable]

∑ Subwoofer

About 10 cm (4q)

For the center speaker cable [4 m (13 feet) cable ]

≥In the same way, attach the sticker to the front speaker cable (R) and the

surround speaker cables (L,R).

Copper

Silver

Preparation

Attach the stickers to the speaker cables.

e.g., For the front speaker (L) cable

About 10 cm (4q)

SC-HT1500(P,PC)04.6.39:07AMページ5

2Connect the speaker cables to the subwoofer.

Push!

Copper

Silver

If irregular coloring occurs on your television

The supplied speakers are designed to be used close to a television,

but the picture may be affected with some televisions and setup

combinations.

If this occurs, turn the television off for about 30 minutes.

The television’s demagnetizing function should correct the problem.

If it persists, move the speakers further away from the television.

SUBWOOFER

5CENTER

3SURROUND (L)

4SURROUND (R)

1FRONT (L)

2FRONT (R)

Speaker-cable sticker

[Note]

≥Never short-circuit positive (i) and negative (j) speaker wires.

Notes on speaker use

≥You can damage your speakers and shorten their useful life if you play

sound at high levels over extended periods.

≥Reduce the volume in the following cases to avoid damage.

–When playing distorted sound.

–When the speakers are receiving howling from a record player, noise

from FM broadcasts, or continuous signals from an oscillator, test disc,

or electronic instrument.

–When adjusting the sound quality.

–When turning the unit on or off.

≥Do not stand on the base and shake the speaker. Be cautious when

children are near.

≥Be sure to connect only positive (copper) wires to positive (i) terminals and negative (silver) wires to negative

(j) terminals.

Incorrect connection can damage the speakers. Copper Silver

Insert the wire fully.

Push !

SC-HT1500(P,PC)04.6.39:07AMページ6

R-AUDIO

–

G-LINK

–

AUDIO

–

OUT1

OPTICAL

TO SB-WA1500

VIDEO S

VIDEO

VIDEO S

VIDEO

–

AUDIO

–

VIDEO S

VIDEO

OUT2

IN1

IN3

–

AUDIO

–

LOOP

ANT

GND

LOOP 75ΩEXT

VIDEO S

VIDEO (L1)

(L3)

AM ANT FM ANT

AUX

RF IN

RF OUT

COMPONENT

VIDEO OUT

(480/480I)

VHF/UHF

RF IN

VIDEO

OUT

VHF/UHF

RF IN

R L

AUDIO OUT

COMPONENT

VIDEO IN

S-VIDEO IN

S-VIDEO OUT

VIDEO IN

Do not connect the unit through a video cassette

recorder

Video signals fed through video cassette recorders will be affected by

on the television.

≥When connecting to a television with a built in VCR, connect to the

input terminals on the television side, not the VCR side.

STEP 4Video connections

∑ 75 ≠coaxial cable ∑ Video cable

Outdoor antenna

Cable TV

Indoor antenna

Main unit

Television

VCR

Television

Main unit

VCR

Television

VCR

Main unit

75 ≠coaxial

cable

➜ page 9

75 ≠coaxial cable

Use a splitter if

you also want to

connect the

antenna to your

VCR.

Video cable S-Video cable

S-Video cable

COMPONENT VIDEO OUT

terminal ➜ page 9

Audio/Video cable

Component

video cable

S-VIDEO OUT

terminal ➜ page 9

Preparation

Before connection, turn off all equipment and read the appropriate operating instructions.

≥The equipment connections described are examples.

≥Peripheral equipment and optional cables sold separately unless otherwise indicated.

∑ Main unit

To the antenna

Splitter

Antenna

cable

VIDEO OUT

RF IN

RF OUT

Red White Yellow

To OUT1 or OUT2

To IN1 (L1)

indicates included accessories.

indicates accessories not included.

Connecting a cable TV box.

(➜ page 10)

Connecting a television and VCR

SC-HT1500(P,PC)04.6.39:07AMページ7

∫COMPONENT VIDEO OUT terminal

These terminals can be used for either interlace or progressive output

(Operations Guide➜page 45) and provide a purer picture than

the S-VIDEO OUT terminal.

≥Connect to terminals of the same color.

∫S-VIDEO OUT terminal

The S-VIDEO OUT terminal achieves a more vivid picture than the VIDEO

OUT terminal. (Actual results depend on the television.)

Use one of the following connections to suit the antenna lead.

≥If your television has both lead and coaxial VHF terminals, use the lead

connection to minimize signal loss. Use one of the following connections to suit the antenna terminals on your

television. Refer to the television’s operating instructions.

∫75 ≠coaxial cable

The picture and sound signal from this unit does not go through the

75 ≠coaxial cable to the television. Make sure you connect one of

the following terminals on this unit to the television: the VIDEO OUT

terminal, the S-VIDEO OUT terminal or the COMPONENT VIDEO OUT

terminal. If the television has none of these terminals, consult your local

dealer.

≥Refer below if the antenna connector doesn’t match.

∫A single twin lead

∫A twin lead and a coaxial cable

∫A twin lead and coaxial plug terminal

∫Two twin leads

from the antenna

VHF/UHF band mixer

(Flat) Twin lead 300 ≠cable

(Round) 75 ≠coaxial cable

To this unit’s RF IN

terminal

To this unit’s RF IN

terminal

300–75 ≠transformer

(Flat) Twin lead

300 ≠cable

VHF/UHF band separator

75 ≠coaxial cable

VHF

UHF

VHF

UHF

Television

VHF/UHF band separator

≥Connect to one of the ANT terminals, then change the television’s

settings as necessary.

75 ≠coaxial cable

Television

Split out

ANT 2

ANT 1

Television

∫A twin lead terminal

∫Two twin lead terminals

∫Multiple antenna terminals

75–300 ≠transformer

75 ≠coaxial cable

VHF or UHF

Television

To this unit’s RF IN terminal

If the antenna connecter doesn’t match

Other antenna connections to the unit Other antenna connections from the unit to the

television

SC-HT1500(P,PC)04.6.39:07AMページ8

VIDEO S-VIDEO

R L

AUDIO

OUT IN

G-LINK

OUT1

OPTICAL

–

AUDIO

–

TO SB-WA1500

VIDEO S

VIDEO

–

AUDIO

–

VIDEO S

VIDEO

–

AUDIO

–

VIDEO S

VIDEO

OUT2

IN1

IN3

–

AUDIO

–

LOOP

ANT

GND

LOOP 75ΩEXT

VIDEO S

VIDEO (L1)

(L3)

AM ANT FM ANT

AUX

RF IN

RF OUT

COMPONENT

VIDEO OUT

(480/480I)

VHF/UHF

RF IN

S-VIDEO IN

VIDEO IN

∑ IR Blaster

STEP 4Video connections

≥You need to subscribe to a cable TV service to enjoy viewing their programming.

≥Consult your service provider regarding appropriate cable TV box.

≥If you receive your programming solely from a satellite service, the program guide in this unit will not receive program listings or channel

information. Without this information, program-based recordings cannot be made. However, recordings can still be set manually.

Television

Main unit

S-Video cable

Audio/video cable

From antenna or cable TV jack

Connect to either this unit’s RF IN

terminal or IN3 (L3) terminal.

Video cable※

75 ≠coaxial cable※

75 ≠coaxial cable

Connecting a cable TV box

IR Blaster

Insert the IR Blaster jack into the G-LINK

terminal.

The cable TV box is controlled by an IR signal

transmitted through the IR Blaster.

When selecting channels on this unit, the

corresponding channels on the cable TV box also

change accordingly.

≥Only use the included IR Blaster.

Red White Yellow

Cable TV box

※For more information on connections (➜page 8, 9 )

∫If your cableTV box has both AUDIO/VIDEO OUT terminals and RF OUT terminals,

we recommend connecting the AUDIO/VIDEO OUT terminal with the unit’s IN3 (L3) terminal. Using this connection provides better picture quality.

≥The S-VIDEO terminal achieves a more vivid picture than the VIDEO terminal.

Place the IR Blaster in front of the signal sensor of the cable TV box.

Cable TV box Signal sensor

If necessary, use the double sided adhesive tape (included) to secure the

IR Blaster to a ﬂat surface

Setting the IR Blaster

Read the cable TV box operating instructions regarding

positioning of the signal sensor.

If you peel off the adhesive tape, the surface may become

damaged.

Once you have conﬁrmed the cable TV box is operating

correctly, secure it by attaching the adhesive tape.

e.g. Television stand surface

Setting the IR Blaster ➜below

indicates included accessories.

indicates accessories not included.

SC-HT1500(P,PC)04.6.39:07AMページ9

G-LINK

OUT1

OPTICAL

–

AUDIO

–

TO SB-WA1500

VIDEO S

VIDEO

–

AUDIO

–

VIDEO S

VIDEO

OUT2

STEP 5Radio and system connections

∑ System cable ∑ AM loop antenna ∑ FM indoor antenna ∑ AC power supply cords

DEO

IDEO

—

AUDIO

—

VIDEO S

VIDEO

IN1

—

AUDIO

—

LOOP

ANT

GND

LOOPEXT

VIDEO S

VIDEO (L1)

(L3)

AM ANT FM ANT

COMPONENT

VIDEO OUT

(480/480I)

IN3

Adhesive tape

Fix the other end of the

antenna where the

reception is best.

Stand the antenna up on

its base.

Place the antenna where

the reception is best.

Keep loose antenna

cable away from other

wires and cables.

FM indoor antenna

Main unit

Catch is facing up Catch is facing down

Loosen the terminal with a

Phillips-head screwdriver.

Tighten the terminal screw again.

White Red

Black

Main unit

1Connect the antennas. 3Connect the AC power supply cords.

≥Connect both AC power supply cords to enjoy all the features of this

system. (The cords are the same.)

Push up.

Insert the antenna cables fully.

To disconnect

Press the catch and pull out.

Catch

Subwoofer

Click!

2Connect the system cable.

AM loop antenna

System cable

AC power supply cords

AC IN terminal

Main unit

Subwoofer

AC IN terminal

Conserving power

The main unit consumes a small amount of power, even when it is turned

off (approx. 14.0 W). To save power when the unit is not to be used for a

long time, unplug it from the household AC outlet.

Turn off the power on the main unit, and remove the AC power

supply cord once “BYE” disappears from the unit’s display.

≥Note that the television program list (Operations Guide➜page 6) is not

downloaded while the unit is unplugged.

To household AC outlet

(AC 120 V, 60 Hz)

Lights when the main unit turns on.

SC-HT1500(P,PC)04.6.39:07AMページ10

Andere Handbücher für SC-HT1500

Inhaltsverzeichnis

Andere Panasonic Heimkinosystem Handbücher

Panasonic

Panasonic SCBTT350 - 3D BLU-RAY HOME THEATRE Bedienungsanleitung

Panasonic

Panasonic SC-HT67 Bedienungsanleitung

Panasonic

Panasonic SCHTB10 - HOME THEATER AUDIO SYSTEM Bedienungsanleitung

Panasonic

Panasonic SC-HT280 Bedienungsanleitung

Panasonic

Panasonic sc-pt460 Bedienungsanleitung

Panasonic

Panasonic SAHT80 - RECEIVER W/ 5-DISK D Bedienungsanleitung

Panasonic

Panasonic SC-HT500 Bedienungsanleitung

Panasonic

Panasonic sc-pt150 Bedienungsanleitung

Panasonic

Panasonic SC-PT170 Bedienungsanleitung

Panasonic

Panasonic SCBT330 - BLU RAY HOME THEATER SYSTEM Gebrauchsanweisung

Panasonic

Panasonic SCHT930 - DVD THEATER RECEIVER Bedienungsanleitung

Panasonic

Panasonic SC-XH150 Bedienungsanleitung

Panasonic

Panasonic SC-XH385GA Bedienungsanleitung

Panasonic

Panasonic SA-HT822VP Bedienungsanleitung

Panasonic

Panasonic SCPTX5 - DVD HOME THEATER SOUND SYSTEM Bedienungsanleitung

Panasonic

Panasonic SA-HT855E Bedienungsanleitung

Panasonic

Panasonic SC-HT855 Bedienungsanleitung

Panasonic

Panasonic SCBT300 - BLU-RAY DISC HOME THEATER SOUND... Bedienungsanleitung

Panasonic

Panasonic SC-BTT190 Gebrauchsanweisung

Panasonic

Panasonic SA-HT840GC Bedienungsanleitung

Panasonic

Panasonic SC-PT760 Bedienungsanleitung

Panasonic

Panasonic SC-PT860 Bedienungsanleitung

Panasonic

Panasonic SA-BT235P Bedienungsanleitung

Panasonic

Panasonic SC-HT80 Bedienungsanleitung

Beliebte Heimkinosystem Handbücher anderer Marken

Samsung

Samsung HT-ES4200K Bedienungsanleitung

Harman Kardon

Harman Kardon HS 100 Bedienungsanleitung

Samsung

Samsung HT-P10 Bedienungsanleitung

Philips

Philips HTS5131 Betriebsanleitung

Goodmans

Goodmans GDVD19SWS Bedienungsanleitung

Moxi

Moxi media center Bedienungsanleitung

Samsung

Samsung HT-EM35 Bedienungsanleitung

LG HE903PAW Bedienungsanleitung

Bose

Bose SoundTouch 520 Bedienungsanleitung

Sony

Sony BDV-N990W Bedienungsanleitung

Manta

Manta GK-500 Bedienungsanleitung

Sharp

Sharp SBW800 Bedienungsanleitung

Philips

Philips HTS3541 Bedienungsanleitung

LG LHT799 Bedienungsanleitung

Samsung

Samsung HT-TWZ415 Bedienungsanleitung

Loewe

Loewe REFERENCE 52 SL FHD+ 200 NMP Bedienungsanleitung

Samsung

Samsung AH68-02166R Bedienungsanleitung

RCA

RCA 600-Watt Bedienungsanleitung