Panasonic VL-SWD275 Bedienungsanleitung

Installation Guide

Model Name Model No.

Wireless Video Intercom System VL-SWD275

Main Monitor Station VL-MWD275

RThis guide is for use with the above 2 models.

VL-V524 VL-MWD275

Door station Main monitor station

RDoor station is described as "doorphone" and Main monitor station is described as "main

monitor" in this guide.

RIn this guide, the suffix of each model number (e.g., the "BX" in "VL-MWD275BX") is omitted

unless necessary.

Note to the installer

RBefore attempting to connect or operate this product, please read the nameplate on

the bottom or rear of the product.

RPlease read this guide carefully, and install the product safely and correctly by following

the instructions. Carefully read the information found in the section titled "For your

safety" in particular.

ROnly use attachments/accessories specified by the manufacturer.

RThe installation shall be carried out in accordance with all applicable installation rules.

RAfter installation, make sure to leave this guide with the customer.

To the maximum extent permitted by law, Panasonic assumes no responsibility for

injuries or property damage resulting from failures arising out of improper installation or

operation inconsistent with this document.

For your safety

To prevent severe injury or loss of life or

property, and to ensure proper and safe

operation of your product, read this

section carefully before using the

product.

WARNING

Preventing fire, electric shock and

short circuits

RLeave installation work to the

dealer. Installation work requires

technique and experiences. Failure

to observe this may cause fire,

electric shock, injury, or damage

to the product. Consult the dealer.

RElectrical connection work should

be performed by certified

personnel only. Certification is

required for performing electrical

connection work. Consult your

dealer.

RUse only the specified power supply

unit and AC cable.

RDo not attempt to disassemble or

modify this product. Contact an

authorised service centre for repairs.

RNever install wiring during a lightning

storm.

RDo not connect non-specified devices.

RDo not connect a power cable to a

terminal that is not specified in this

guide.

RWhen opening holes in walls for

installation or wiring, or when

securing the power cable, make sure

you do not damage existing wiring

and ductwork.

RDo not make any wiring connections

when the power supply is turned on.

RDo not use the supplied power supply

unit for outdoor installations (it is for

indoor use only).

RDo not install the main monitor/

extension monitor in the following

places:

– Places where the main monitor/

extension monitor may be

splashed with water or chemicals.

– Places where there is a high

concentration of dust, or high

humidity.

RDo not place objects on the power

cables and the AC adaptor. Install the

product where no one can step or trip

on the power cables and the AC

adaptor.

RDo not allow the power cables and

the AC adaptor to be excessively

pulled, bent or placed under heavy

objects.

RWhen existing wires are used, it is

possible that they contain AC voltage.

Contact an authorised service centre.

Preventing accidents and injuries

RDo not install or use the product in

health care facilities if any regulations

posted in the area instruct you not to

do so. Hospitals or health care

facilities may be using equipment that

could be sensitive to external RF

(radio frequency) energy.

RDo not install or use this product near

automatically controlled devices such

as automatic doors and fire alarms.

Radio waves emitted from this

product may cause such devices to

malfunction, resulting in an accident.

CAUTION

Preventing electric shock

RIf the wiring is underground, do not

make any connections underground.

RIf the wiring is underground, use a

protection tube.

RIf the wiring is outdoors, use a

protection tube or a surge protector.

Preventing injury

RInstall the product securely adhering

to the instructions in this guide to

prevent it from falling off the wall.

Avoid installing onto low-strength

walls, such as gypsum board, ALC

(autoclaved lightweight concrete),

concrete block, or veneer (less than

18 mm thick) walls.

RTo prevent serious injuries due to the

product unexpectedly falling, the

product with a wall mount feature

must be installed at a height of 2 m or

lower.

Supplied accessories for installation

For the doorphone*1

Mounting base ´ 1

Screw ´ 2

(3.8 mm ´ 20 mm)

Screw ´ 4

(4 mm ´ 12 mm)

For the main monitor/extension monitor

Screw ´ 2

(4 mm ´ 16 mm)

Mounting bracket ´ 1

Power supply unit and related items*2

Cable binder ´

Power supply unit ´ 1

(VL-PS241)

AC cable ´ 1 Screw ´ 2

(4 mm ´ 40 mm)

Important:

RYou will need the following additional items to install and configure the doorphone and the

main monitor/extension monitor.

[Locally procured]

– DC cable*2 and wires (for doorphone and other connections):

Prepare a cable and wires of the appropriate specification. (a"Wire type and length")

Note:

RThe illustrations in the supplied manual(s) may vary slightly from the actual product.

*1 VL-SWD275 models only

*2 VL-SWD275AZ/VL-MWD275AZ models only

Precautions for installation

To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/

extension monitor in the following locations:

– Places where vibration or any other kind of impact occurs.

– Places where echoing is frequent.

– Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.

For the doorphone

RIf a strong light is shining on the doorphone, the visitor’s face may not be distinguishable. Do not place

the doorphone in the following locations:

– Where most of the background is the sky.

– Where the background is a white wall, and direct sunlight will reflect off it.

– Where direct sunlight will shine on the doorphone.

RDo not place the doorphone in locations where echoing occurs, as this will cause the doorphone to

beep frequently.

RDust protection/water protection is IP44.

Only when installation work specified in this guide is properly performed and appropriate water

protection treatment is performed.

RMake sure the rear of the doorphone is not subject to water.

RDepending on the installation location, condensation may form on the doorphone’s lens cover. This

may cause images to become obscured. Condensation will dissipate as the temperature rises.

For the main monitor/extension monitor

RInstall the main monitor away from electronic appliances such as TVs, radios, personal computers, air

conditioners, boiler control panels with intercom, home security equipment, wireless devices, or digital

cordless phones.

RLeave at least 20 cm of space above, below, and to the left and right sides of the main monitor/

extension monitor. Do not install on a wall that is deeply recessed.

RDo not install the main monitor/extension monitor inside a wall.

RBe sure to install the main monitor/extension monitor more than 5 m away from the doorphone.

RThe product operates in the frequency range of 1.88 GHz and 1.90 GHz with a peak transmission

power of 250 mW (max.). Refer to the "For best performance" section in the Operating Instructions.

RIn areas surrounded by a high electrical field, disturbances may occur in the main monitor’s/extension

monitor’s image or sound.

Important:

RDo not use any cleaning products that contain alcohol, polish powder, powder soap, benzine, thinner,

wax, petroleum, or boiling water. Also do not spray the product with insecticide, glass cleaner, hair

spray or wall paint. This may cause a change in colour or quality of the product.

Wiring schematic diagram

Set up correctly according to the following wiring schematic diagram and "Wire type and length".

RFor information, such as order numbers, about optional devices that can be connected to, refer to the

"Additional/replacement accessories" section in the Operating Instructions.

Ml-1

Ml-2

Ml-1

Ml-2

Ml-1

Ml-2

EXTENSION

MONITOR 1

EXTENSION

MONITOR 2

EXTENSION

MONITOR 3

DOORPHONE 1 DOORPHONE 2

Electric

lock

Electric

lock NP: Non-polarised

MAIN MONITOR

Ml-1

Ml-2

IN1

IN2

IN3

IN4

MO-1

MO-2

MO-3

MO-4

MO-5

MO-6

Connection device

for option Input

(A contact) *2 PBX

A A

Terminal box

(4-conductor

wiring)

You can also connect an

optional lobby station. (See

page 7.)

*1 *1

POWER SUPPLY UNIT

24 V DC

Power supply

*1 When you use an additional doorphone, the maximum number of the electric locks that can be

connected to the doorphone depends on the type of doorphone. Consult your dealer for further

information.

For VL-V554 users:

– The electric lock can also be connected to the S1/S2 terminals of the doorphone.

*2 Connection devices for option input (A contact).

– Make sure to connect doorbells to the IN3/IN4 terminals. A doorbell and doorphone 2 cannot be

used together.

– When a VL-V901 and VL-V700 series Video Intercom System for Apartment Complexes is used,

emergency terminals can be used. Make sure to connect emergency terminals to the IN1/IN2

terminals.

*3 VL-SWD275AZ/VL-MWD275AZ models only

Wire type and length

Wiring run Wire type*1

Diameter Length (Max.)

Doorphone –

Main monitor –

Extension monitor*2

ø 0.65 mm 22 AWG 100 m

ø 1.0 mm 18 AWG 130 m

ø 0.5 mm CAT 5 50 m

Main monitor –

Power supply unit

ø 0.65 mm 22 AWG 10 m

ø 1.0 mm 18 AWG 20 m

Main monitor –

Electric lock*3

ø 0.5 mm - ø 1.2 mm

(24 AWG - 17 AWG)

According to the

specifications of the

connected device.

Main monitor –

Connection device for

option input (A contact)*3

ø 0.5 mm - ø 1.2 mm

(24 AWG - 17 AWG)

According to the

specifications of the

connected device.

Main monitor –

PBX ø 0.65 mm CAT 3 or 22 AWG 100 m

*1 Type: Single-pair cable with outer sheath (jacket)

Conductor: Copper solid

RA certified power supply wiring has to be used with this equipment. The relevant national

installation and/or equipment regulations shall be considered. A certified power supply wiring not

lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.

*2 When an extension monitor is used, make sure that the total wiring length from the doorphone to the

main monitor and then to the extension monitor, is within about 100 m.

*3 When using an electric lock or a connection device for option input (A contact), select a device that

meets the following guidelines:

RElectric lock connection terminal (S1/S2, S3/S4):

– N/O dry closure contact

– 30 V AC (1 A)/24 V DC (1 A) or lower

RConnection device for option input (A contact) terminal (IN1/IN2/IN3/IN4):

– Input method: No-voltage contact

– Open-circuit voltage between terminals: DC 7 V or less

– Detection definite time: 0.1 second or more

– Short-circuit between terminals: 5 mA or less

– Resistance value: make: 500 W or less, break: 15 KW or more

n Connecting an optional lobby station

For information about connections, refer to the documentation of the lobby station to be connected.

MAIN MONITOR

Ml-1

Ml-2

IN1

IN2

IN3

IN4

MO-1

MO-2

MO-3

MO-4

MO-5

MO-6

Example: VL-V591 Lobby station

NP: Non-polarised

RConnecting an optional VL-V591 lobby station

– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the lobby station.

– Connect terminal S1/S2 on the main monitor with terminal S1/S2 on the lobby station.

– After connecting to the main monitor, change the [Lobby connection] setting to [Device connected]

using the main monitor. (®Operating Instructions of the Video Intercom System.)

Note:

RConnection for VL-V901 and VL-V700 series Video Intercom System for Apartment Complexes

– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the VL-V701 Distribution Box.

RConnection for VL-VM series/VL-VM701 Video Intercom System - Lobby station/Distributor

– Connect either terminal D1/D2 or D3/D4 on the main monitor with the terminal on the Lobby station

or VL-VM701 Distributor.

Doorphone installation position

Installation position of the doorphone and camera range

Views when the camera is facing forwards at 0° (default).

RExample: Installation height is 1450 mm (standard position).

(Units: mm)

A view when looking

from above

A Image range B Approx. 54° C Centre of doorphone D Approx. 1450 E Approx. 500

F Approx. 1740 G Approx. 510 H Approx. 1230 I Image range: Approx. 920 J Approx. 85°

K Approx. 500

The camera angle can be adjusted using the camera angle control lever on the rear of the

doorphone (step 3, “Installing the doorphone”), so that the image range can be changed.

Side view when the camera is installed

lower than the standard position, and

facing upwards at 15°.

Top view when the camera is facing left or

right at 15° *1.

RExample: Installation height is 1100 mm.

(Units: mm)

RExample: Camera angle faces left 15°.

A Image range B Approx. 54° C Centre of doorphone D Approx. 1100 E Approx. 500

F Approx. 1590 G Approx. 560 H Approx. 1030 I Image range: Approx. 1050 J Approx. 260

K Approx. 790 L Approx. 85° M Approx. 500

*1 If the camera points 15° upwards, the left or right angle is less than 5°.

Note:

RThe measurements and angles are for reference purposes and may vary depending on the

environment.

Installing the doorphone

Important:

ROn the bottom surface of the doorphone and the

mounting base, there are holes to allow water to

drain. Do not cover them up when installing.

RWhen existing wiring (such as chime wires) is

used:

– It may contain AC voltage that may cause

electric shock and/or damage the product.

– Never use the following types of wiring.

Consult a qualified technician/dealer.

RSee "Wire type and length" for information about

wiring materials.

1Attach the mounting base (B) (accessory) to

the wall securely.

RInstall the mounting base on a vertical flat

wall.

A Screws (accessory) ´ 2

C Wire (locally procured)

D 83.5 mm

*1 To prevent dew condensation, fill a hole

for wiring as much as possible.

When using flush mount box (option):

Model No. VL-MB524

Install the flush mount box (A) in the

wall.

B Knockout hole*1

C Approx. 90 mm D Approx. 138 mm

E Approx. 37 mm

*1 Only open the knockout holes as

required for the wiring.

2Use a slotted screwdriver (A) to push into the

holes on the bottom side of the front panel,

and remove the front panel (B) of the

doorphone.

3Adjust the camera angle using the camera

angle control lever.

Rear view

B C

A Camera angle control lever

B Left (maximum 15°)

C Right (maximum 15°)

D Upwards (maximum 15°)

Examples of camera angle

Facing upper leftFacing left

Facing forwards Facing upwards

RThe angle can also be adjusted to the right

or upper right.

Important:

RWhen the camera angle is adjusted to the

upper left or upper right, the image may be

slightly distorted.

4Connect the wires.

Loosen the screws. Push in the wires to the

terminal connectors (non-polar), then tighten

the screws (A).

A– Recommended torque: 0.5 N·m

{5.1 kgf·cm}

– Maximum torque: 0.7 N·m {7.1

kgf·cm}

5Attach the doorphone to the mounting base.

A Screws (accessory) ´ 4

When using flush mount box (option):

Model No. VL-MB524

Attach the doorphone to the flush mount

box.

A Screws (locally procured) ´ 4

R4 mm ´ 25 mm, stainless steel

(the same type of screw as the 4 mm ´

12 mm supplied accessory but with a

different length)

6Attach the front panel in the order of A ® B.

Andere Handbücher für VL-SWD275

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Gegensprechanlage Handbücher

Panasonic

Panasonic VL-SWD701KL Bedienungsanleitung

Panasonic

Panasonic VL-SWD501EX Bedienungsanleitung

Panasonic

Panasonic VL-SVN511 Series Bedienungsanleitung

Panasonic

Panasonic VL-WD619 Bedienungsanleitung

Panasonic

Panasonic KX-T7765X Bedienungsanleitung

Panasonic

Panasonic VL-SDM310 Bedienungsanleitung

Panasonic

Panasonic Condominiums HA D Series Bedienungsanleitung

Panasonic

Panasonic VL-SWD501EX Bedienungsanleitung

Panasonic

Panasonic VL-GC3700BX Technisches Handbuch

Panasonic

Panasonic VL-SVN511 Series Bedienungsanleitung

Panasonic

Panasonic VL-VC3500BX Technisches Handbuch

Panasonic

Panasonic VL-SV74 Bedienungsanleitung

Panasonic

Panasonic VL-SWD501BX Bedienungsanleitung

Panasonic

Panasonic VL-SW102BX Bedienungsanleitung

Panasonic

Panasonic VL-SWD501 Bedienungsanleitung

Panasonic

Panasonic VL-SV70 Betriebsanleitung

Panasonic

Panasonic VL-SV74 Bedienungsanleitung

Panasonic

Panasonic VL-VN1500 Bedienungsanleitung

Panasonic

Panasonic VL-MV26 Bedienungsanleitung

Panasonic

Panasonic KX-T7775 Bedienungsanleitung

Panasonic

Panasonic Windea VGDT18143W Bedienungsanleitung

Panasonic

Panasonic VL-VN1800 Bedienungsanleitung

Panasonic

Panasonic VL-MVN511 Bedienungsanleitung

Panasonic

Panasonic VL-MV72AZ Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung