Panasonic VL-SWD501 Bedienungsanleitung
2013 Wireless Video Intercom
INSTALLATION GUIDE
System
System configuration and wiring
configuration and wiring
VL-SWD501 System Component
VL-SWD501EX wiring schematic diagram
VL-SWD501EX wiring type and length
Door Station
Door Station Installation
Installation
Installing the door station (VL-V554EX)
Installing the door station (VL-V554UEX)
Door station installation position
Main
Main Monitor Station Installation
Monitor Station Installation
Installing the main monitor station
Main monitor station installation position
Power Supply Unit
Power Supply Unit Installation
Installation
Installing the power supply unit (VL-PS241)
Initial Setup
Initial Setup
Setting the date and time
Changing the date and time
Setting Demo mode
Registering wireless monitor stations
Installing Wireless Sensor Cameras
Installing Wireless Sensor Cameras
Install the wireless sensor camera
If connecting an external sensor
Using external sensor (About the external input terminal )
Wire type and length
Installation location for the wireless sensor camera
Registering the wireless sensor camera to the main monitor station
Viewing wireless sensor camera images
( Monitoring the out side with the wireless sensor camera)
Registering DECT repeaters
Registering DECT repeaters
Registering DECT repeaters to the main monitor station
Cancelling
Cancelling
Cancelling wireless monitor stations,
wireless sensor cameras, DECT repeaters
Specifications
Specifications
Main Monitor Station
Power Supply Unit
Door Station
Wireless Monitor Station (Main body)
Wireless Monitor Station (Charger)
Wireless Sensor Camera
DECT Repeater
…….………………………. 4
………….....… 5
………….……..…. 6
…….........…..… 8
……........….. 10
…………………………. 12
……………..………. 17
……......…. 19
…......…. 21
……………...………..………… 24
…………………..………….. 25
……………………..….………………… 26
………..………. 27
..………………………………… 29
…..…………..…………………….. 31
……….. 33
………………………………………………….……… 34
............ 35
.. 36
…………………………….. 38
………. 41
…….…… 43
………………………………………………………. 45
………………………………….……………………… 46
………………………………………….………………………. 47
……………………………… 48
…………………………………… 49
…………………………………………………… 50
………………………………………….………..……..……. 52
INDEX
INDEX
System configuration and wiring
System configuration and wiring
VL
VL-
-SWD501 System Component
SWD501 System Component
5-inch
wide screen
touch panel 2.2-inch TFT
colour LCD
Wireless
Monitor Station
(Sub monitor)
VL-WD613
Up to
2
DECT
Repeater
VL-FKD2
Up to
2Up to
4
Up to
6
Door Station
(Doorphone)
Door Station
(Doorphone)
VL-V554
Main Monitor Station
(Main monitor) Wireless Monitor Station
(Sub monitor)
Wireless
Sensor Camera
VL-WD812
Basic System Component
Optional Expandability
VL-SWD501
5
6
Power
supply
Power
supply
Power
supply
Power
supply
NP
NP NP
NP
NP
NP
NP
NP
Electric lock
(Electric vehicle gate lock)*1
12 VAC/DC
12 VAC/DC
12 VAC/DC
12 VAC/DC
220-240 VAC
24 V DC
Electric lock
(Electric vehicle gate lock)*1
Electric lock
(Electric door lock)*2
Electric lock
(Electric door lock)*2
DA
D
E
B
C
Connection device for option
output (A contact)
*1 Make sure to only connect electric vehicle gate locks to the S3/S4
terminals of the door stations.
*2 Make sure to only connect electric door locks to the S1/S2 terminals
of the door stations.
Main Monitor Station
Door Station 1
Door Station 2
Power Supply Unit
NP: Non-polarised
VL
VL-
-SWD501EX wiring schematic diagram
SWD501EX wiring schematic diagram
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
●A certified power supply wiring has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered.
A certified power supply wiring not lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When using an electric lock or a connection device for option output (A contact), select a device
that meets the following guidelines:
●Electric lock connection terminal (S1/S2, S3/S4):
--N/O dry closure contact
-- 12 V AC/DC, less than 1 A
●Connection device for option output (A contact) terminal (OUT1/OUT2):
-- 24 V AC/DC, less than 0.3 A (minimum contact: 5 V DC 1 mA)
Wiring run Wire type*1
Diameter Length (Max.)
Main Monitor Station –
Door station A
φ0.65 mm 22 AWG 100 m
φ1.0 mm 18 AWG 130 m
φ0.5 mm CAT 5 50 m
Main Monitor Station –
Power Supply Unit Bφ0.65 mm 22 AWG 10 m
φ1.0 mm 18 AWG 20 m
Power Supply Unit –
AC power source Cφ1.2 mm - φ2.0 mm
(17 AWG - 12 AWG) No requirement
Door Station –
Electric Lock*2 Dφ0.5 mm - φ1.2 mm
(24 AWG - 17 AWG) According to specification
of connected device.
Main Monitor Station -
Connection device for option
output (A contact)*2 Eφ0.5 mm - φ1.2 mm
(24 AWG - 17 AWG) According to specification
of connected device.
VL
VL-
-SWD501EX wiring type and length
SWD501EX wiring type and length
Door Station Installation
Door Station Installation
Screws x 2 *
Mounting base
Wire
83.5
mm
Wall
Installing the door station
(VL-V554EX)
Attach the mounting base to the wall
securely.
Use a hex wrench to loosen screw A and
remove the front panel of the door station.
Front panel
Screw A
2 mm hex wrench
Connect the wires
<Rear view>Terminals for the
electric locks
Terminal for the
main monitor station
1Loosen the screws.
2Push in the wires to the terminal connectors
(non-polar), then tighten the screws.
•Install the mounting base on a vertical flat wall.
Step 1 Step 2
Step 3
(locally procured)
Door Station
Door Station Installation
Installation
Installing the door station
(VL-V554EX)
Attach the door station to the mounting base.
Screws x 4
Name plate Screw A
•Write the name on the name plate as needed.
Attach the name plate to the door station and
use screw A to secure the front panel.
Important
• On the bottom surface of the door station and the
mounting base, there are holes to allow water to drain. Do
not cover them up when installing.
• When existing wiring (such as chime wires) is used:
- It may contain AC voltage that may cause electric shock
and/or damage the product.
-
Never use the following types of wiring. Consult a qualified
technician/dealer.
Step 4
Step 5
Door Station
Door Station Installation
Installation
Installing the door station
(VL-V554UEX)
Install the flush mounting box in the wall. Use a hex wrench to loosen screw A and
remove the front panel of the door station.
Front panel
Screw A
2 mm hex wrench
Connect the wires
<Rear view>
Terminal for the
electric lock
Terminal for the
main monitor station
1Loosen the screws.
2Push in the wires to the terminal connectors
(non-polar), then tighten the screws.
151mm
Flush mounting box
Knockout hole*1
100mm
37mm
*1 Only open the knockout holes as required for
the wiring.
Step 1 Step 2
Step 3
Door Station
Door Station Installation
Installation
Inhaltsverzeichnis
Andere Panasonic Gegensprechanlage Handbücher
Panasonic
Panasonic WX-CC411BP Bedienungsanleitung
Panasonic
Panasonic VG-M186D Bedienungsanleitung
Panasonic
Panasonic VL-VF580 Bedienungsanleitung
Panasonic
Panasonic VL-SW102BX Bedienungsanleitung
Panasonic
Panasonic Condominiums HA D Series Bedienungsanleitung
Panasonic
Panasonic VL-SW250BX Bedienungsanleitung
Panasonic
Panasonic Windea HA D Series Bedienungsanleitung
Panasonic
Panasonic VL-MWD275 Bedienungsanleitung
Panasonic
Panasonic VL-SV71 Bedienungsanleitung
Panasonic
Panasonic Windea VGDT18143W Bedienungsanleitung
Panasonic
Panasonic 1M Installationshandbuch
Panasonic
Panasonic VL-MW250BX Bedienungsanleitung
Panasonic
Panasonic VL-V900 Bedienungsanleitung
Panasonic
Panasonic VL-GC003A Betriebsanleitung
Panasonic
Panasonic VL-SWD501EX Bedienungsanleitung
Panasonic
Panasonic VL-SWD272BX Bedienungsanleitung
Panasonic
Panasonic VL-GM001 Betriebsanleitung
Panasonic
Panasonic VL-SWD272 Bedienungsanleitung
Panasonic
Panasonic VL-V900 Bedienungsanleitung
Panasonic
Panasonic VL-SV71 Betriebsanleitung
