Panasonic BT-S1315DA Bedienungsanleitung

bt_s1415.html
Table Of Contents 
COVER 
1 Safety Precautions 
1.1 General Guidelines 
1.2 Leakage Current Cold Check 
1.3 Leakage Current Hot Check 
1.4 X-Radiation 
1.5 Horizontal Osc. Disable Circuit 
Test 
1.6 Repair Procedure of Horizontal 
Osc. Disable Circuit 
2 Disassembly Instructions 
2.1 Printed Circuit Board Layout 
2.2 Removal of Top Cabinet 
2.3 Removal of Rear Cover 
2.4 Removal of DS-P.C.Board (for 
BT-S1315DAD&sol;S1415DAD only) 
2.5 Removal of B- andW-
P.C.Boards 
2.6 Removal of A-P.C.Board 
3 Picture Tube Replacement 
3.1 Replacement Procedure 
3.2 Location of Magnets 
4 Measurements and Adjustments 
4.1 Adjustment procedure Flowchart 
4.2 Location of Test Points and 
Adjustment Control 
4.3 Warnings 
4.4 Caution 
Service Manual
TOP NEXT 
VED0006296C0
D6
Color Video Monitor
BT-S1315DA/BT-S1315DAD/BT-S1415DA/BT-S1415DAD
G19M-1 Chassis
file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/PVAccel.html (1 z 4) [2006-02-04 08:28:01]

bt_s1415.html
5 Notes 
6 Switching between USER and 
FACTORY Modes 
7 Purity Adjustment 
7.1 Equipment to be used 
7.2 Adjustment Procedure 
8 Convergence Adjustment 
8.1 Equipment to be used 
8.2 Adjustment Procedure 
9 Deflection Adjustment and 
Check 
9.1 Equipment to be used 
9.2 Initial Settings 
9.3 Adjustment Procedure 
10 Cut Off Adjustment 
10.1 Equipment to be used 
10.2 Initial Settings 
10.3 Adjustment Procedure 
11 Contrast Adjustment 
11.1 Equipment to be used 
11.2 Initial Settings 
11.3 Adjustment Procedure 
12 NTSC Color Output 
Adjustment 
12.1 Equipment to be used 
12.2 Initial Settings 
12.3 Adjustment Procedure 
13 White Balance Adjustment 
13.1 Equipment to be used 
13.2 Initial Setting 
© 2000 Matsushita Electric Industrial Co., Ltd./All rights reserved. Unauthorized copying and distribution is a violation of law.
•@
TOP NEXT 
file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/PVAccel.html (2 z 4) [2006-02-04 08:28:01]

bt_s1415.html
13.3 Preparations 
13.4 6500K Adjustment 
13.5 9300K Adjustment 
14 SECAM Black Level 
Adjustment 
14.1 Equipment to be used 
14.2 Initial Settings 
14.3 Adjustment Procedure 
15 Brightness and ABL 
Adjustment 
15.1 Equipment to be used 
15.2 Initial Settings 
15.3 Adjustment Procedure 
16 Focus Adjustment 
16.1 Equipment to be used 
16.2 Initial Settings 
16.3 Adjustment Procedure 
17 C&sol;Y Output Adjustment 
(BT-S1315DAD&sol;S1415DAD only) 
17.1 Equipment to be used 
17.2 Adjustment Procedure 
18 X-radiation Protection Circuit 
Adjustment 
18.1 Equipment to be used 
18.2 Initial Settings 
18.3 Adjustment Procedure 
Troubleshooting 
1 The power is not turned on 
2 No raster appears 
3 The raster is a horizontal 
file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/PVAccel.html (3 z 4) [2006-02-04 08:28:01]

bt_s1415.html
5.4 No picture appears 
5.5 No on-screen display appears 
5.6 No sound comes out 
6 Operating Instructions 
7 Block Diagram 
8 Schematic Diagram for Models BT-
S1315DA&sol;DAD and BT-
S1415DA&sol;DAD 
9 Schematic Diagram 
9.1 W-P.C.Board 
9.2 A-P.C.Board(1&sol;2) 
9.3 A-P.C.Board(2&sol;2) 
9.4 B-P.C.Board(1&sol;2) 
9.5 B-P.C.Board(2&sol;2) 
10 Circuit Boards 
10.1 A-P.C.Board 
10.2 B-P.C.Board&sol; W-
P.C.Board(Foil Side) 
10.3 B-P.C.Board (Component Side) 
Y&sol;S&sol;T&sol;N&sol; Board(Foil 
Side) 
11 Exproded Views   
12 Replacement Parts List 
file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/PVAccel.html (4 z 4) [2006-02-04 08:28:01]
PV

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0100000000x.html

1 Safety Precautions

TOP PREVIOUS NEXT

1.1 General Guidelines

1.2 Leakage Current Cold Check

1.3 Leakage Current Hot Check

1.4 X-Radiation

1.5 Horizontal Osc. Disable Circuit Test

1.6 Repair Procedure of Horizontal Osc. Disable Circuit

•@

TOP PREVIOUS NEXT

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0101000000.html

1.1 General Guidelines

TOP PREVIOUS NEXT

It is advisable to insert an isolation transformer in the power line and AC supply before servicing a hot

chassis.

When servicing this monitor, observe the original lead dress, especially the lead dress in the high

voltage circuits. If a short circuit is found, replace all parts which have been overheated or damaged

by the short circuit.

After the service, check that all the protective devices such as insulation barriers, insulation papers,

shields, and isolation R-C combinations are properly installed.

Before turning the monitor on, measure the resistance between B+ Iine and chassis ground. Connect

the "-" side of an ohmmeter to each B+ Iine, and the "+" side to chassis ground. The resistance of each

line must behigher than specified as follows:

When the monitor is not used for a long period of time, unplug the power cord from the AC outlet.

High voltage points, as high as 23.5 kV, are present when this monitor is in operation. Operating the

monitor without the rear cover involves you in a dangerous electric shock from the monitor power

supply. Servicing must not be attempted byanyone who is not thoroughly familiar with the necessary

precautions when working on high voltage equipment. Always discharge the anode of the picture tube

to the chassis ground before handling the picture tube.

After the service, make the following leakage current checks to prevent the customer from getting an

electric shock.

•@

TOP PREVIOUS NEXT

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0102000000.html

1.2 Leakage Current Cold Check

TOP PREVIOUS NEXT

1. Unplug the AC power cord and connect a jumper wire between the two prongs of the AC plug.

2. Set the power switch of this monitor to the ON position.

3. Measure the resistance with an ohmmeter between the prongs of the AC plug and each exposed

metallic cabinet part on the monitor such as screw heads, connectors, and control shafts. When

the exposed metallic part has a return path to the chassis,the ohmmeter should read between 5

MΩ and 15 MΩ. When the exposed metallic part does not have a return path to the chassis, the

reading must be infinity.

•@

TOP PREVIOUS NEXT

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0103000000.html

1.3 Leakage Current Hot Check

TOP PREVIOUS NEXT

1. Plug the AC power cord directly into the AC outlet. Do not use an isolation transformer for

this check.

2. Connect the test jig shown in Fig.1 between each exposed metallic part on the monitor and an

earth ground such as a water pipe.

3. Use an AC voltmeter having high impedance (1 kΩ/V or higher) to measure the voltage.

4. Measure the voltage at each exposed metallic part.

5. The voltage at any point must be less than 0.25 V[rms].

6. A Ieakage current tester (Simpson Model 228 or equivalent) may be used to make the hot

checks. In this case, the current must be less than 0.5 mA.

7. If the reading is outside of the specified limit, the monitor must be repaired and rechecked

before it is returned to the customer because of a possibility of an electric shock.

Fig.1

•@

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0103000000.html (1 z 2) [2006-02-04 08:28:11]

TOP PREVIOUS NEXT

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0103000000.html (2 z 2) [2006-02-04 08:28:11]

file:///E:/BT-S1315DA_BT-S1315DAD_BT-S1415DA_BT-S1415DAD/SVC/s0104000000.html

1.4 X-Radiation

TOP PREVIOUS NEXT

Warnings:

The potential sources of X-Radiation in the monitor are the high voltage section and the picture tube.

When using a picture tube test jig for service, check that the jig is capable of handling 28.5 kV

without causing X-Radiation.

Note:

It is important to use an accurate, periodically calibrated high-voltage meter (electrostatic type).

1. Turn the BRIGHT and CONTRAST controls counterclockwise fully.

2. Check that the high voltage is 23.5 kV±1.5 kV. If not, immediate service and correction is

required to prevent a possibility of premature component failure.

3. To prevent an X-Radiation possibility, it is essential to use the specified picture tube.

•@

TOP PREVIOUS NEXT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Monitor Handbücher

Panasonic

Panasonic M-900 Series Bedienungsanleitung

Panasonic

Panasonic PT47WXD63G - 47" PROJECTION TV Bedienungsanleitung

Panasonic

Panasonic CY-VM5899U Bedienungsanleitung

Panasonic

Panasonic CY-V7100U Bedienungsanleitung

Panasonic

Panasonic TH-65PF9BK Bedienungsanleitung

Panasonic

Panasonic TH-65LFB70E Bedienungsanleitung

Panasonic

Panasonic TH-85PF12U Bedienungsanleitung

Panasonic

Panasonic TH-42PM50U Bedienungsanleitung

Panasonic

Panasonic TH-65PF12EK Bedienungsanleitung

Panasonic

Panasonic PT53WX52F - 53" PROJECTION TV HD Bedienungsanleitung

Panasonic

Panasonic TH-65PB1W Bedienungsanleitung

Panasonic

Panasonic Viera TH-42PW3 Bedienungsanleitung

Panasonic

Panasonic BT-LH80W Bedienungsanleitung

Panasonic

Panasonic TH-42LFP30W Bedienungsanleitung

Panasonic

Panasonic PT-56DLX25 Bedienungsanleitung

Panasonic

Panasonic BTLH1800 - LCD HD MONITOR Bedienungsanleitung

Panasonic

Panasonic BT-LH2550 Bedienungsanleitung

Panasonic

Panasonic TH-65PF10WK Bedienungsanleitung

Panasonic

Panasonic TH-43LFE8U Bedienungsanleitung

Panasonic

Panasonic TY-ST08S Bedienungsanleitung

Panasonic

Panasonic TH-85VX200C Betriebsanleitung

Panasonic

Panasonic Toughbook CF08 Handbuch

Panasonic

Panasonic WVCM1420 - COLOR MONITOR Bedienungsanleitung

Panasonic

Panasonic TH-42PWD8WK Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung