Panasonic CF-VDL01 Bedienungsanleitung

Panasonic®

LCD Monitor

OPERATING INSTRUCTIONS

Model No. CF-VDL01

Contents

introduction 4

Names and Functions of Parts .....5

Mounting the LCD Monitor .....6

Starting Up/Shutting Down 8

Touchscreen IMM V

Adjusting the LCD Monitor 1

Troubleshooting .............*BB.BBBBBBBBB.BBBBB 14

Specifications 15

WARNING

ALCD monitor may be installed in amotor vehicle and visible to the driver if the LCD monitor is used for vehicle information,

system control, rear or side observation or navigation. If the LCD monitor is used for television reception or video or DVD play,

the LCD monitor should be installed so that these features will only function when the parking brake is applied. ALCD monitor

used for television reception, video or DVD play or text data that operates when the parking break is not applied must be installed

to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. This statement

should be reviewed with each state to allow for the safe and lawful use of this product while operating avehicle.

Car Directive Compliance Notice

This LCD monitor is in conformance with the requirements of the European Council Directive 95/54/EC adapting to technical

progress 72/245/EEC.

e-mark certificate No. el 3*72/245*95/54*0550*00

(D Use This Product Safely

WARNING

To avoid risk of serious injury or possible violation of laws, make sure that the monitor is placed visible to the driver for

no other purpose than navigational or with the use of rear view camera only.

When Driving

0The driver must not operate the LCD monitor.

(Operating the LCD monitor while driving is adistraction and may lead to an accident.)

©As asafety factor, driving with the television, video or DVD player is prohibited.

®Keep the unit at an appropriate sound level. Driving with the sound at a level that prevents you from hearing sounds

outside and around the car may cause an accident

When Car Washing

Do not expose the LCD monitor to water or excessive moisture. This could cause electrical shorts, fire or other damag*

When Parked

OParking in direct sunlight can produce very high temperatures inside your car. Let the interior of the car cool down before

switching the unit on.

ODo not watch the LCD monitor with the engine off. It will consume battery power and may prevent the engine from starting.

Use Panasonic Technical Support

GDo not attempt to disassemble or adjust this precision product. Contact Panasonic Technical Support.

For Installation

•Be sure to install the LCD monitor in aposition that does not obstruct the driver's vision.

•If the LCD monitor has been installed for the rear seat passengers, they must be careful to prevent injury by hitting their heads

on the LCD monitor in case of an accident.

•Do not expose the LCD monitor to direct sunlight or excessive heat.

•Be sure not to install the LCD monitor in alocation at which it is exposed to water, hot air such as near heater duct, or where

it may stepped on.

•Do not install the unit in an area where it would obstruct the operation of an air bag.

•Ask atrained technician to install the unit. Installation and wiring require training and experience.

To be safe, ask the sales outlet where you purchased the unit to perform the installation.

When Operating

#Make sure the LCD monitor is firmly secured and protected from strong impact, because this may cause amalfunction or

possible fire.

[Illustration in this manual]

(indicates Microsoft® Windows® 95 Operating System,

(indicates Microsoft® Windows® 98 Operating System,

(indicates Microsoft® Windows NT® Operating System,

(indicates Microsoft® Windows* 2000 Professional Operating System.

Windows 95

Windows 98

Windows NT

Windows 2000

Microsoft®, MS-DOS® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other coun-

tries.

Introduction

Thank you for purchasing the LCD Monitor for the Panasonic CF-17/M34 notebook computer series.

This LCD monitor features atouchscreen function, which makes computer operation possible by simply touching the surface of

the LCD monitor and pressing buttons -even when the computer is not being held.

/LCD Monitor. Operating Instructions

Keyboard

RGB Cable

Serial Cable

Sound Cable PS/2 Cable. Function Cable

Names and Functions of Parts

Emergency Button

The applicationsoftware alio

cated to (F11 )is started up.

Brightness Volume| (#

Qdown

Speaker Volume |(B

Cdown

Temperature LED Indicator

<Front>

Green :Normal

The brightness can be ad-

justed freely.

Orange :Drops the brightness auto-

matically due to an in-

crease in the internal tem-

perature.

Red :The backlight goes OFF

automatically due to an in-

crease in the internal tem-

perature.

Speaker Function Buttons

LED Indicator

Green :power on

Orange :power on but no VGA Sig-

nal or the cable is not con-

nected.

|Power Switch (|)

Speaker

Does the same operation as (ZD

through CFS) of the keyboard.

Sound Port line in

DC-INJack ^<&<2>DCMNi5V n

Display Port RGB IN

-\Function Key Port Fn KEY

Serial Port serial i/f

Binder]

Bind the cables and

fix firmly. OSD buttons I(D

C^page11 Reserve

Do not have anyone except an

authorized repairperson push

this button.

Mounting the LCD Monitor

7Connect your computer to the port replicator

((^Operating Instructions of the port replicator)

2Remove the cover of the LCD Monitor

Remove the four screws, and remove the cover.

£Connect the LCD Monitor to your computer (through the port replicator) and stand-

alone keyboard via the connection cables (included)

Fn KEY

(?) RGB cable

(2) Serial cable

(3) Sound cable

0PS/2 cable

(5) Function cable

4Attach the cover of the LCD Monitor

Attach the four screws.

Mount the LCD Monitor

Use these M4 screw holes to mount the LCD Monitor.

•When installing the LCD monitor, locate the monitor under the dashboard as

shown in the figure to prevent the monitor from interrupting the sight of the

driver and to prevent the monitor from being hit by direct sunlight.

#Do not expose the computer to direct sunlight or excessive heat.

Starting Up/Shutting Down

Starting Up

7Turn the LCD Monitor on

Press the power switch.

2Turn your computer on (cooperating Instructions of the computer)

3Select your application

You are able to start working on your computer.

Shutting Down (power off your computer)

This procedure is shutting down without using the suspend or hibernation function.

(C2? Reference Manual of the computer "Suspend/Hibernation Functions")

Display the shut down screen

After saving important data and closing each application, select [Shut Down] from the [Start] menu.

Confirm shut down

Windows 95 IWindows 98 IWindows 2000

Select [OK] after selecting [Shut down].

Your computer will power off automatically.

(In the OFF state, if you are not recharging your battery pack or if the pack is fully charged, your computer consumes approximately 1.5 W.)

Windows NT

Select [OK] after selecting [Shut down the computer].

Your computer will power off automatically.

(In the OFF state, if you are not recharging your battery pack or if the pack is fully charged, your computer consumes approximately 1.5 W,)

Turn the LCD Monitor off

Press the power switch.

The LCD Monitor will not turn off until the computer is shut down completely.

Touchscreen

The LCD Monitor is equipped with atouchscreen function allowing you to perform the same operations as the touch pad or mouse

by touching the surface of the display with your finger. (The operation settings can be changed in [Start] -[Programs] -[Updd] -

[Settings].)

Moving the cursor Clicking

Cursor

Double-clicking Dragging

Touch and hold the object (i. e.

file or icon), move your finger

on the surface (dragging the

object to the desired location),

then release your finger.

The touchscreen function can not be used in the MS-DOS mode and when using the full

screen in [MS-DOS prompt].

When the operation ofpanning (only LCD) is performed while the screen resolution is

set to [1024 x768 dots] or more, the touchscreen function will not work properly.

If achange is made to the screen resolution, or the cursor can not be pointed correctly

with your finger, be sure to perform calibration in the [Start]-[Programs]-[Updd]-[Cali-

brate] menu.

Handling-theTouchscreen-,

•Do not place any object on the surface or press down forcefully with sharp-pointed objects

(e.g., nails), hard objects that can leave marks (e.g., pencils and ball point pens).

•Do not apply pressure within 5mm of the perimeter of the display panel. The cursor may

move to the edge of the display.

•Do not operate the computer when such things as dust are on the screen, or allow contact

with substances that could dirty the touchscreen, such as oil. The cursor may not work

properly in such cases.

•When the touchscreen becomes dirty:

Use adry soft cloth such as agauze to clean the dirty areas.

Do not use benzene, thinner, or disinfectant- type alcohol.

Touchscreen

Configuringthe Touchscreenn

When needed, the touchscreen can be configured using the following steps.

7Select from the taskbar or select [Settings] from [Start] -[Programs] -[Updd]

The following screen will appear.

Windows

Set the "double-click" set-

tings.

Devices

Configure the device controller.

Hardware

Set the hardware resources.

Match this setting with the setting

for [Touchscreen] and [Serial Port

B] in the Setup Utility.

Settings

Set the general protocol

settings.

i— Calibration

Define the calibration setup.

Use when the cursor can not be pointed correctly with your

finger. (Needed if the alignment of the touchscreen with the

visual image change or adjust the display resolution).

Before you run the calibration, you need to set the device at

[Calibration settings for] as followings.

[Device 1] is for the computer

[Device2] is for the LCD Monitor

Status

Display the status of the controller.

About

Display the version number.

Button Modes

Set the button modes.

General

Set the general settings and functions.

Events

Set the events that can be generated by a

controller.

Advanced

Set the advanced settings. /note)-

IFor more inFor more information, refer to [Help]. J

Make necessary changes

Click [OK]

^oteV

Adjustments can be made when double-click operations are assumed by the computer although single-click opera-

tions are intended, by clicking [Windows] from the display shown above and decreasing the value for [Time] in

[DoublcClick Settings].

It is also possible to change the double click speed for [Buttons] in [Start] -[Settings] -[Control Panel] -[Mouse]. It

is important to note that when the double click speed for [Mouse] is changed, the double click time for [Windows] is

also changed. However, the double click time for [Windows] and [Mouse] returns to its value before the change

when the computer is restarted.

Immediately run [Calibrate] when the number of points of calibration is changed.

Andere Handbücher für CF-VDL01

Inhaltsverzeichnis

Andere Panasonic Monitor Handbücher

Panasonic

Panasonic PANASYNC PRO P110I Bedienungsanleitung

Panasonic

Panasonic TH-42LF6U Bedienungsanleitung

Panasonic

Panasonic TH-85VX200W Bedienungsanleitung

Panasonic

Panasonic TH-42PF50U Bedienungsanleitung

Panasonic

Panasonic WVCK1420A - COLOR MONITOR Bedienungsanleitung

Panasonic

Panasonic TH-85PF12U Bedienungsanleitung

Panasonic

Panasonic TH-42PF11UK - 42" Plasma Panel Bedienungsanleitung

Panasonic

Panasonic TH-37PX60U Kurzanleitung

Panasonic

Panasonic TH-42PH12ES Bedienungsanleitung

Panasonic

Panasonic VIERA TH-P55VT60A Bedienungsanleitung

Panasonic

Panasonic TH-65PB1U Bedienungsanleitung

Panasonic

Panasonic 58PF12UK - TH - 58" Plasma Panel Bedienungsanleitung

Panasonic

Panasonic CY-VMR5800N Bedienungsanleitung

Panasonic

Panasonic TH-42PHD6BX Bedienungsanleitung

Panasonic

Panasonic TH-55LFV50W Bedienungsanleitung

Panasonic

Panasonic TH-103PF12U Betriebsanleitung

Panasonic

Panasonic PT-60LCX64-K Bedienungsanleitung

Panasonic

Panasonic TH-58PF20U TENTATIVE Bedienungsanleitung

Panasonic

Panasonic TH-42LF8U Bedienungsanleitung

Panasonic

Panasonic CY-VM5800U Bedienungsanleitung

Panasonic

Panasonic PT-51HX42CF Bedienungsanleitung

Panasonic

Panasonic TH50PH10UKA - 50" Plasma Panel Bedienungsanleitung

Panasonic

Panasonic WVBM1400 - B&W CAMERA Bedienungsanleitung

Panasonic

Panasonic CYVM5800U - 5.8" CLR MONITOR/DVD Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung

LG M1950D-PZ Bedienungsanleitung