Panasonic CF-VDW07HM Bedienungsanleitung
Panasonic Wireless Display Monitor – CF-VDW07HM
Installation & Configuration
General
The Panasonic Wireless Display Monitor (WDM) can be installed either in Ad-Hoc mode or
Infrastructure mode. In Ad-Hoc mode, the WDM communicates directly with the PC it is
controlling via the wireless card in the PC. In Infrastructure mode, the WDM communicates
through a Wireless Access Point (or Wireless Router) to the PC it is controlling. In
Infrastructure mode, the PC that is being controlled does not need to have a wireless card. Since
this is the typical configuration for use with Scrap Dragon, that is the method that is described
herein. Each WDM can be configured with 4 different profiles, allowing a single WDM to
control up to 4 different computers on the network.
Installing the Software on the PC
1. On the computer that will be controlled by the Wireless Display Monitor (WDM).
2. Install the MeiWDS software from the installation CD. Run setup.exe from the \meiwds
folder.
3. Reboot the computer. The Wireless Display Setup Utility icon will appear in the
system tray. This is a Windows service, WDS Server.
4. Install the software keyboard from the installation CD. Run setup.exe from the \softkb
folder.
Infrastructure Setup
It is necessary to set the parameters of the Access Point and the PC to the WDM defaults to
establish the initial connection. Once the WDM is connected to the PC, the Wireless Display
Setup Utility is used to change the parameters to the ones that are appropriate for your network.
Isolate the PC and the Access Point from the
rest of the network. Turn on the WDM. If
the WDM has never been connected, you
will see this screen:
If you don’t see this screen, it is because the
WDM has previously been connected.
Follow the instructions on the next page to
get to this screen.
Skip this page if you see this screen:
Press the MENU button on the WDM, you
will see this screen:
Select [Option] using the stylus, you will see
this screen:
Select [Setup] using the stylus, you will see
this screen:
Choose the Profile you wish to configure,
you will see this screen:
Select Infrastructure, you will see this screen
with the information needed to make the
initial connection using the built in default
values. The IP Address of the PC and the IP
Address, SSID and Encryption of the Access
Point MUST match the values displayed
here. While you can use Class A, Class B or
Class C, these instructions assume you are
using Class C.
Select Class C. The default IP Address will be something like 192.168.19.49, and the subnet
mask will be 255.255.255.0. Follow these steps:
1. Determine the current IP address of the Access Point and the user name and password to
login. If this is a new unit, then it will be the default IP address and login. Consult the
user manual for the specific values.
2. In Internet Explorer enter the IP address of the Access Point and login to the
configuration page. Note that the IP address scheme of the PC must match the IP address
scheme of the Access Point or it will not be accessible. You may have to temporarily
change the IP address of the PC.
3. Set the SSID of the Access Point to cfvdw07 and disable encryption. Save the changes.
4. Change the IP address of the Access Point to an address that is the same scheme as the
default address for the PC that is indicated in the WDM. For example, if the default
address is 192.168.19.49, then set the Access Point address to 192.168.19.1. Do not use
an IP address that is just one larger than the default as this is assigned to the WDM. Save
the changes.
5. Change the IP address and subnet mask of the LAN card in the PC to match the default
address for the PC that is indicated in the WDM. For example, 192.168.19.49.
6. It is NOT necessary to create a wireless network profile as indicated in the Panasonic
instruction manual.
7. Left click on the MeiWDS icon in the system tray, then click Password. Enter the
default password wdsp and then OK.
8. Disable any Windows firewall software that might prevent connectivity, or create a port
exception for TCP 11900.
9. On the WDM, select [Connect] with the stylus. If the connection is successful, the screen
on the handheld will mirror the PC, and the MeiWDS icon in the system tray will change
from to .
At this point, the WDM should be communicating with the PC and the screens should be
mirrored. This will also enable access to the Wireless Display Setup Utility that allows the
WDM to be reconfigured to the actual parameters that you wish to use on your network.
Left click on the MeiWDS icon in the system tray and then click Run Setup Utility. Or run
the Wireless Display Setup Utility from the start menu.
Wireless Display Setup Utility
The Wireless Display Setup Utility can only
be run when the WDM is connected to the
PC. The first screen of the Wireless Display
Setup Utility looks like this:
Make sure you are on the correct profile.
You can change the SSID, the encryption,
the IP Addresses and the subnet mask. You
can also give the profile a meaningful name.
When you click the Next button, the new
settings will be saved in the WDM and you
will be prompted to make the corresponding
changes in the Access Point and in the PC.
When changing IP Addresses, always
change the Access Point first, or you will
not be able to connect to it from your
browser.
If necessary, you can repeat this process for other PC’s, using a different profile for each.
You can now reconnect the Access point and the PC to the rest of the network. The WDM
should connect to the PC whenever the WDM is turned on and this profile selected.
Inhaltsverzeichnis
Andere Panasonic Monitor Handbücher
Panasonic
Panasonic BTLH1700W - 17" HD MONITOR Bedienungsanleitung
Panasonic
Panasonic TH-50PH30U Bedienungsanleitung
Panasonic
Panasonic TH-65SF2U Bedienungsanleitung
Panasonic
Panasonic TH-65PF11WK Bedienungsanleitung
Panasonic
Panasonic PANASYNC TX-D9S45MB Bedienungsanleitung
Panasonic
Panasonic PANASYNC TX-D7S35 Bedienungsanleitung
Panasonic
Panasonic BT-LH1770P Bedienungsanleitung
Panasonic
Panasonic TH-42PF20U Bedienungsanleitung
Panasonic
Panasonic BTH1390Y - COLOR VIDEO MONITOR Bedienungsanleitung
Panasonic
Panasonic TH-37PR10R Bedienungsanleitung
Panasonic
Panasonic CT-1030M Bedienungsanleitung
Panasonic
Panasonic TH-65PHD8BK Bedienungsanleitung
Panasonic
Panasonic TH-75CQ1W Bedienungsanleitung
Panasonic
Panasonic PT-56LCX70 - 56" Rear Projection TV Bedienungsanleitung
Panasonic
Panasonic TH-50PF9EK Bedienungsanleitung
Panasonic
Panasonic BT-S915 Bedienungsanleitung
Panasonic
Panasonic TH-65PF9BK Bedienungsanleitung
Panasonic
Panasonic TH-50LFB70E Bedienungsanleitung
Panasonic
Panasonic TH-58PH10UKA - 58" Plasma Panel Bedienungsanleitung
Panasonic
Panasonic PT-44LCX65 - 44" Rear Projection TV Bedienungsanleitung
