Panasonic AY-RP500 Bedienungsanleitung

AY-RP500 / AY-EB500

ORDER NO. BSD9802022C1

C1998 Matsushita Communication Industrial Co., Ltd.

distribution is a violation of law.

Nonlinear Editing System

Control Panel Kit / Hard Disk Box

SPECIFICATIONS

AY-RP500

Power Supply : 5V DC, -12V

Power Consumption : JOG Board : 37.7W

JOGPAD : 2.1W

Ambient Operating Temperature : 5˚C - +35˚C

Ambient Operating Humidity : 10% - 90%

Weight : JOG Board : 0.3kg

JOGPAD : 1.15kg

AY-EB500

Power Supply : 220-240V AC 50Hz

Power Consumption : 89W

WIDE SCSI Input : x2

WIDE SCSI Output : x2 (Loop through output)

HDD dimensions : 3.5” (102 (W) x 152 (D) x MAX. 42 (H) mm)

Installable HDD Units : max. 2

Connectable HDD-BOXes : max. 5

Ambient Operating Temperature : 0˚C - +35˚C

Ambient Operating Humidity : 10% - 90%

Dimensions : 210(W)x132(H)x310(D) mm

8-1/4”(W)x5-3/16”(H)x12-3/16”(D)

Weights : Min. 5.4 kg (11.9 lbs.)

without HDD

Max. 7.5 kg (16.6 lbs.)

with HDD's

Weight and dimensions are approximate.

Specifications are subject to change without notice

AY-RP500 AY-EB500

This service information is designed for experienced repair technicians only and is not designed for use by the

general public.

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to

service a product.

Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any

attempt to service or repair the product or products dealt with in this service information by anyone else could

result in serious injury or death.

!WARNING

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This symbol warns the user that uninsulated voltage within

the unit may have sufficient magnitude to cause electric

shock. Therefore, it is dangerous to make any kind of contact

with any inside part of this unit.

This symbol alerts the user that impotant literature concerning

the operation and maintenance of this has been included.

Therefore, it should be read carefully in order to avoid

any problems.

There are special components used in this equipment which are important for safety. These parts are indicated

by the ”Y” mark on the schematic diagram and the replacement parts list. It is essential that these critical

parts should be replaced with manufacturer's specified parts to prevent shock, fire, or other hazards.

Do not modify the original design without permission of manufacture.

IMPORTANT SAFETY NOTICE

CONTENTS

Major Operating Controls And Thier Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Board Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Hard Disk Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Location of Test Points and Adjusting Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Conductor View

JOG Board (AY-RP500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Power Board (AY-EB500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Schematic Diagram

JOG Board (AY-RP500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Power Board (AY-EB500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Exploded View of AY-RP500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Exploded View of AY-EB500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

MAJOR OPERATING CONTROLS AND THEIR FUNCTION

JOG BOARD

1. ISA connector

This connector is used to connect the personal comput-

er.

2. Interrupt number (IRQ) setting jumper (Pg)

Set the interrupt number (IRQ) where the jumper pin is

inserted.

3. I/O port setting jumper (P12)

Set the I/O address where the jumper pin is inserted.

4. RS422 control connector 1 (RS422-1)

This connector is used to connect a device that can be

controlled through a RS422 interface via the special

cable (accessory). This connection can be used to con-

trol recording and playback on a VTR.

5.RS422 control connector 2 (RS422-2)

This connector is used to connect a device that can be

controlled through a RS422 interface via the special

cable (accessory). This connection ca be used to con-

trol recording and playback on a VTR.

6. JOGPAD connector (JOGPAD)

This connection is used to connect a JOGPAD via the

special cable (accessory).

7. Time code, reference input/output connector

(LTC/REF)

This connector is used to connect, via the special time

code and reference I/O cable (accessory), with the time

code input and output on a VTR, etc., and with equip-

ment that inputs an external signal for synched compos-

ites (horizontal sync only).

• Time code input and output

This connector is used to connect with the time code

input and output on a VTR, etc. Make this connection

only if the VTR has a time code signal (LTC) output.

The time code output is not a loop-through of the signal

that was input on the time code input.

Ver. 1.0 software does not support time code input and

output.

• Reference input and output

This connector is used to connect with equipment that

inputs an external sync signal. Be sure to input the ref-

erence signal so as to maintain the frame precision. If a

reference signal is not input, video, audio, ant time code

synchronization, and time code I/O operation, cannot be

guaranteed. The reference code output is a loop-

through of the signal that was input on the reference

input.

8.Reference I/O 75-ohm terminator switch

No function.

When not using the REF OUT signal, turn off the switch

and connect the termination (accessory) to the REF

OUT cable.

OPEN

UNDO SHIFT

TRIM

MODE

DIVIDE

DELETE

ZOOM /

GOTO /

PLAY/STOP

MARK IN

MARKOUT

JOG PAD

er ty

1. Positioner

Set the key position. Is ineffective with Ver. 1.0 soft-

ware.

2. Wipe Lever

Controls the Wipe speed and audio volume. Is ineffec-

tive with Ver. 1.0 software.

3.TRIM / MODE / N

Used in Trim mode.

(Shift + TRIM/MODE) Turn Trim mode On/Off.

4.DIVIDE / DELETE B

Deletes a clip.

(SHIFT + DIVIDE / DELETE) Divides a clip

5.ZOOM / N

Zooms in the time line.

(SHIFT + ZOOM) Zooms out the time line.

6. GOTO / B

Jumps to the starting or editing mark.

(SHIFT + GOTO) Jumps to the beginning or end of a

sequence.

7. MARK OUT

Sets or cancels the ending mark.

(SHIFT + MARK OUT) Selects the grip of the OUT

point.

8.MARK IN

Sets or cancels the starting mark.

(SHIFT + MARK IN) Selects the grip of the IN point.

9.PLAY / STOP

Plays back or stops.

(SHIFT + PLAY /STOP) Plays back between the start-

ing and ending marks.

10. Shuttle Ring

Plays back video and audio forward (clockwise) or in

reverse (counterclockwise) with variable speed.

11. Jog Dial

Plays back video and audio forward (clockwise) or in

reverse (counterclockwise) frame by frame.

12. SHIFT

Switches button functions.

13. UNDO

Cancels the immediately previous operation.

14. OPEN / OK

Registers the Log in the Log List (when batch digitized

used).

15. Jog Pad Connector

Connects with the Main Unit by using the JOGPAD

Cable (accessory).

FRONT PANEL

REAR PANEL

1. Power Button/Power Indicator (POWER)(Red)

Press this button to turn on the power. The Power

Indicator lights red while the power is on.

Caution: Do not turn off the power during recording or

playback mode.

2. HDD Operating Indicator (HDD)(green)

Green light indicates that the HDD is in operation.

3. SCSI ID Setup Switch for Channel A (SCSI ID,

chA)

The SCSI-ID for Channel A is set with this switch.

Refer to page 8 for ID Number Setting.

4. SCSI ID Setup Switch for Channel B (SCSI ID,

chB)

The SCSI-ID for Channel B is set with this switch.

5. Fans

These Fans prevent temperature rise inside the unit.

Note: The fans are wear items and need to be replaced

periodically.

POWER HDD

AY-EB500

B A

chA

3210 chB

3210

SCSI ID

chA

I N OUT I N OUT

chB

~AC IN

io!0

Operating Time Operating Life

8 hours daily 6 years

12 hours daily 4 years

24 hours daily 2 years

6. AC Inlet (~ AC IN)

Connect the provided power cord to this Inlet.

7. SCSI Output Connector for Channel B

(chB/OUT)

Connect the “chB/IN” terminal of an additional HDD-BOX

to this connector.

8. SCSI Input Connector for Channel B (chB/IN)

Connect the “chB/OUT” terminal of an additional HDD-

BOX to this connector.

Used for connection with the channel B SCSI connector

of the SCSI PCB.

9. SCSI Output Connector for Channel A

(chA/OUT)

Connect the “chA/IN” terminal of an additional HDD-BOX

to this connector.

10. SCSI Input Connector for Channel A (chA/IN)

Connect the “chA/OUT” terminal of an additional HDD-

BOX to this connector.

Used for connection with the channel A SCSI connector

of the SCSI PCB.

AY-EB500

BOARD SETUP

Install the boards in the computer.

There are three boards to be installed.

1. Video compression board (TARGA200DV board)

2. SCSI board

3. JOG board [AY-RP500 board (JOG board)]

Preparation

1.Turn off the computer.

2.Open the case of the computer. For details on how to do so, refer to the instruction manual that was provided with the computer.

3.Confirm which PCI slot (the white connector on the motherboard) the video card is installed in. If the video card is already in the

PCI slot that is the farthest from the CPU, you do not need to move the video card.

4.In all other cases, move the video card according to the procedure described in steps 5 through 8 below.

5.Remove the screws that secure the cover for the PCI slot that is farthest from the PCI, and then remove that cover.

6.Remove the screws that secure the cover for the video card, and then remove the video card.

7.Plug the video card into the PCI slot that is farthest from the PCI, and secure the cover in place with the screws.

8.Store the screws and cover that were removed in a safe place.

CPU

SCSI board

TARGA2000DV board AY-RP500 board

(JOG board)

Video card

BIOS setup

1.This procedure sets up the motherboard BIOS.

2.Open the BIOS setup screen. (The method of calling up

the BIOS setting screen varies depending on the

computer. Refer to the user's manual of the computer.)

3.Set "Plug & Play OS" to "OFF". (The setting on your

computer system may be "Disable" or "No".)

4.Set Power Management to "OFF". (This may be "Disable"

or "No".)

5.Save the settings, and quit the BIOS setup screen. The

computer starts up automatically.

6.Once the computer has started up, confirm that it is

operating normally; then quit WindowsNT and turn off the

computer.

Insert the main board into

the grooves in the rail

guides on the board spacer.

Main board Grooves in the rail guide

on the board spacer.

Installing the Vide Compression board

(TARGA2000DV board)

Note that due to structural differences, the installation

location may differ depending on the model of computer

used.

1.Remove the cover for the PCI slot (the white connector on

the motherboard) that is closest to the CPU.

Note: The construction of some computers does not

physically allow the TARGA2000DV board to be

plugged into the PCI slot that is closest to the CPU. If

this is the case with your computer, remove the cover

for the adjacent PCI slot.

2.Carefully remove the TARGA200DV board from its anti-

static protective pack. If you need to set the board down,

place it on top of this pack.

3.Attach the board spacer to the main board (the longest

board) among the TARGA2000DV boards. (Refer to the

diagram below.)

4.Plug the TARGA2000DV board into the PCI slot that is

closest to the CPU (or the next closest slot, if the board

will not physically fit into the closest slot). Here, firmly

mount the board spacer between the guide rails on the

personal computer. The assembly diagram shown below

is intended as an example. The actual connection

locations may differ depending on the model of computer

used.

5.Connect the CA206 cable that was provided with the

TARGA2000DV board. Plug the connector labelled

"TARGA2000DV" into the connector on the

TARGA2000DV board, plug the connector labelled "VGA"

into the connector on the video card, and connect the

connector labelled "MONITOR" to the monitor cable.

Illustration of image compression board inserted into PC.

Connect the ground wire of the video compression board (board

spacer) to the chassis (metal portion) of the system unit. (Unscrew

the screw and then use it to secure the wire in place.)

6.Store the screws and cover that were removed in a safe

place.

7.Turn the power on and start up WindowsNT.

8.Next, install the driver. Load the CD-ROM of the software

package, and execute "\targa\disk1\setup.exe" of the File

Manager, of the CD-ROM.

9.Follow the instructions to install the driver from the CD-

ROM. Operate according to the procedures below.

1)The window for Truevision TARGA2000DV V1.0 Setup

appears.

Click .

2)The Product Type Inquiry window appears.

Select the type of board to use, and click .

For analog type, select "TARGA2000DV" (default).

For SDI type, select "TARGA2000DV SDX".

(When the type is selected, is displayed.)

3)The Choose Destination Location window appears.

Click .

4)The Select Program Folder window appears.

Click .

5)Installation begins.

6)The Readme window appears.

Click on the upper-right of the window and close it.

7)The Installation Completed Successfully window

appears. Select "Yes, I want to restart my computer

now".

(When this is selected, is displayed.)

Click .

10.Restarts after installation.

At this point, remove the CD-ROM from which the driver

was installed.

Finish

Insert the video compression boars with board spacer attached.

The rail guides

on the personal

computer

11.When WindowsNT has restarted, click "Start".

From Programs in the Start Menu, click "Administrative

Tools" p"Windows NT Diagnostics". The program

starts up.

12.The Windows NT Diagnostics Program window appears.

Click the "Resources" label. The resource list shown

below appears (not in the same layout).

Note: "DVRNTDRV" indicates the TARGA2000DV board.

Check which number is used for the IRQ. After

checking, lick to close the window.

13.Change the display driver.

1)Open the "Control Panel" and double-click "Display".

2)Select from "Display Properties" and click

3)Click in "Display Type".

4)Click in "Display Modification".

Hard Disk

Change

Settings

5)The directory of the display driver is to be opened, so

enter "c:\TARGA2KVD\WINNT\Display" and click .

7)The message "The drivers were successfully installed"

appears. Click .

8)Click in "Display Types".

9)Click in "Screen Properties".

10)The message "You must restart your computer..."

appears. Click .

11)WindowsNT starts up. When the Control Plane opens,

close it.

When the message "A new graphics driver has been

installed" appears, click .

12)Click and drag the mark on the frame of the desktop

area in "Screen Properties" to adjust it for the resolution

of 1152 x 870 pixels. Here, confirm that the font size is

"Small Fonts", and that the Refresh Frequency is 75 Hz.

13)Click , and click to enter test mode. The

test screen appears.

14)If the test screen is displayed correctly, click .

15)Click in "Display Properties" to close this

screen. The resolution will change.

Note: Be sure to modify the display and test it. Otherwise,

the display will not be correct.

Yes

Test

Installing the SCSI board

1.Remove the cover for the PC slot (the white connector on

the motherboard) that is adjacent to the slot where the

TARGA2000DV board is plugged in (on the side away

from the CPU).

2.Carefully remove the SCSI board from its anti-static

protective pack. If you need to set the board down, place

it on top of this pack.

3.Plug the SCSI board into the PCI slot adjacent to the

TARGA2000DV board on the side away from the CPU,

and secure the cover in place with the screws.

4.Store the screws and cover that were removed in a safe

place.

5.For details on the cable connections, refer to the fard disk

setup procedure. (Do not fail to connect the cables.)

6.Turn on the power and start up WindowsNT.

7.Open the Control Panel and start up WindowsNT.

8.Select "Driver" and click .

9.The manufacturer and the SCSI adapter list appear.

Select "Adaptec" for the manufacturer, and "AHA-

294x/AHA-394x or AIC-78xx PCI SCSI controller" for the

adapter, and click .

Here, the WindowsNT CD-ROM is required, so load it and

click .

The "Windows NT CD-ROM" window opens. This is not

needed, so click the on the upper-right of the window to

close it.

10.Specify the directory of the driver. For example, if the

CD-ROM drive is drive E, enter E:\i386, and click .

11.When installation is ended, the message "You must

restart your computer..." appears. Click .

Add

12.When WindowsNT has restarted, click "Start".

From Programs in the Start Menu, click "Administrative

Tools" p"WindowsNT Diagnostics". The program

starts up.

13.The WindowsNT Diagnostics Program window appears.

Click the "Resources" label. The resource list appears.

"aic78xx" indicates the SCSI board. Check which number

is used for the IRQ.

"aic78x" is displayed twice. Both numbers might be the

same or they might not; it does not matter in either case.

After checking, click to close the window.

Andere Handbücher für AY-RP500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Nichtlineares Bearbeitungssystem Handbücher anderer Marken

Sony

Sony EditStation ES-7 Bedienungsanleitung

Sony

Sony DMW-S05NL-C Bedienungsanleitung