Panasonic KX-TDA100AL Bedienungsanleitung

ORDERNO. KMS0303678C3

HybridIP-PBX

KX-TDA100AL

(for Australia)

Unauthorizedcopying and distribution isaviolation oflaw.

IMPORTANTINFORMATION ABOUTLEAD FREE, (PbF), SOLDERING

Ifleadfree solderwas usedinthe manufacture of this productthe printedcircuitboards will be

markedPbF.

Standardleaded, (Pb), soldercanbe usedas usual on boards without the PbF mark.

Whenthis mark does appearplease readand followthe special instructions describedinthis

manual on the use of PbF and howitmight be permissible to use Pbsolderduring service and

repairwork.

1. ABOUTLEADFREE SOLDER(PbF:Pbfree)

Note:

Inthe information below, Pb, the symbol forleadinthe periodic table of elements, will referto

standardsolderorsolderthatcontains lead.

We will use PbF whendiscussing the leadfree solderusedinourmanufacturing process which

is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufacturedusing leadfree solderwill have PbF stampedon

the PCB. Forservice and repairwork we suggestusing the same type of solderalthough, with

some precautions, standardPbsoldercanalsobe used.

Caution

-PbF solderhas amelting pointthat is50° ~70° F, (30° ~40°C)

higherthanPbsolder. Please use asoldering iron with

temperaturecontrol and adjust itto700° ±20° F, (370° ±10°C). In

case ofusing high temperaturesoldering iron, please becareful

nottoheat too long.

-PbF solderwill tend tosplashifitisheatedmuchhigherthanits

melting point, approximately1100°F, (600°C).

-Ifyou must use Pbsolderon aPCB manufacturedusing PbF

solder, removeas muchoftheoriginal PbF solderas possibleand

besurethat anyremaining ismeltedprior toapplying thePb

solder.

-Whenapplying PbF soldertodoublelayeredboards, please check

thecomponentsidefor excess whichmayflowontotheopposite

side(See figure, below).

1.1. SUGGESTEDPbF SOLDER

There are several types of PbF solderavailable commercially. While this productis

manufacturedusing Tin, Silver, and Copper,

(Sn+Ag+Cu), you canalsouse Tinand Copper, (Sn+Cu), orTin, Zinc, and Bismuth, (Sn+Zn+Bi).

Please check the manufac

turer’s specific instructions forthe melting points of theirproducts and anyprecautions for

using theirproductwith other

materials.

The following leadfree (PbF) solderwire sizes are recommendedforservice of this product:

0.3mm, 0.6mm and 1.0mm.

1.2. HOWTO RECOGNIZE THATPbFREE SOLDERIS USED

2. FORSERVICE TECHNICIANS

ICs and LSIs are vulnerable to static electricity.

Whenrepairing, the following precautions will helpprevent recurring malfunctions.

1. Covertheplasticparts boxes withaluminum foil.

2. Ground thesoldering irons.

3. Use aconductivemat on theworktable.

4. DonottouchICor LSI pinswithbarefingers.

3. CAUTION

3.1. NOTE

Whenyou note the serial number, write downall of the 11 digits.

The serial numbermaybe found on the label affixedto the bottom of the unit.

3.2. SAFETY PRECAUTIONS

1. Beforeservicing, unplug thepowercord topreventanelectric

shock.

2. Whenreplacing parts, use onlythemanufacturer's recommended

components for safety.

3. Check thecondition ofthepowercord. Replace ifwearor

damageisevident.

4. Afterservicing, besuretorestoretheleaddress, insulation

barriers, insulation papers, shields, etc.

5. Beforereturning theservicedequipmenttothecustomer, besure

toperform thefollowing insulation resistance test topreventthe

customerfrom being exposedtoshock hazards.

3.3. INSULATIONRESISTANCE TEST

1. Unplug thepowercord and shortthetwoprongsoftheplug with

ajumperwire.

2. Turn on thepowerswitch.

3. Measuretheresistance valuewithohmmeterbetweenthe

jumperedACplug and eachexposedmetal cabinet part, suchas

screwthreads, control shafts, handlebrackets, etc.

Note:

Some exposedparts maybe isolatedfrom the chassis bydesign. These will readinfinity.

4. Ifthemeasurementisoutsidethespecifiedlimits, thereisa

possibilityofshock hazard. Theequipmentshouldberepaired

and recheckedbeforeitisreturnedtothecustomer.

3.4. BATTERY CAUTION

1. Dangerofexplosion ifbatteryisincorrectlyreplaced. Replace

onlywiththesameor equivalenttyperecommendedbythe

manufacturer. Dispose ofusedbatteries according tothe

manufacturer’sInstructions.

2. Thelithium batteryisacritical component(typeNo.CR23541).

Please observefor theproperpolarityand theexact location

whenreplacing itand soldering thereplacementlithium batteryin.

3.5. CAUTION

The powersocketwall outletshouldbe locatednearthis equipment and be easilyaccessible.

4. SPECIFICATIONS

4.1. GENERALDESCRIPTION

Control Bus Original bus (16 bit, 8 MHz,10 megabytes persecond)

Communication Bus H.100 bus conformity(1024 time slot)

Switching Non Blocking DistributedTime Switch

PowerInput PSU-S

(KX-TDA0108) 100 VAC to 130 VAC/200 VAC to 240 VAC, 1.4 A/0.8 A,

PSU-M

(KX-TDA0104) 100 VAC to 130 VAC/200 VAC to 240 VAC, 2.5 A/1.4 A,

External Battery +36 VDC (+12 VDC x 3, batterycapacityof 28 Ahor

below

recommendedfor1 external battery)

Maximum PowerFailure Tolerance 300 ms (without using backup battery)

MemoryBackup Duration 7 years

Dialling Trunk Dial Pulse (DP)10 pps, 20 pps

Tone (DTMF) Dialling

Extension Dial Pulse (DP)10 pps, 20 pps

Tone (DTMF) Dialling

Mode Conversion DP-DTMF, DTMF-DP

Ring Frequency 20 Hz/25 Hz(selectable)

Trunk Loop Limit 1600 maximum

Operating

Environment Temperature 0 °C to 40 °C

Humidity 10%to 90%(non condensing)

Conference Call Trunk From 10 x 3-partyconference call to 4 x 8-party

conference

Music on Hold(MOH) 2 ports (Level Control:-6 dB to +6 dB in3 dB steps)

MOH1:External Music Source port

MOH2:Selectable Internal/External Music Source port

Paging Internal Level Control:-6 dB to +3 dB in3 dB steps

External 2 ports (Volume Control:-15 dB to +6 dB in3 dB steps)

Serial Interface Port RS-232C 1 (max 115.2 kbps)

USB 1

Extension Connection Cable SLT 1 pairwire (T, R)

DPT 1-pairwire (D1, D2)or

2-pairwire (T, R, D1,

D2)

APT 2-pairwire (T, R, D1,

D2)

DSS Consoles and Add-on Key

Module 1-pairwire (D1, D2)

Dimension KX-TDA100 334 mm (W)x 390 mm (H)x 270 mm (D)

(13 5/32 inx 15 11/32 inx 10 5/8 in)

Weight (whenfully

mounted) KX-TDA100 Under12 kg(26.5 lb)

4.2. CHARACTERISTICS

Terminal Equipment Loop Limit -PT:KX-T76xx series and KX-T7560/KX-T7565:90 ;all otherDPTs/APTs:40

-SLT:600 including set

-Doorphone:20

-CS:130

Minimum Leakage Resistance 15000 maximum

Maximum Numberof Extension

Instruments perLine 1 forPTorSLT

2 byParallel oreXtra Device Portconnection of a PTand

Ring Voltage 75 Vrms at20 Hz/25 Hzdepending on the Ringing Load

Trunk Loop Limit 1600 maximum

HookswitchFlash/Recall Timing

Range 24 ms to 2032 ms

BRI Cards Internal ISDN Mode SupplyVoltage:40 V

PowerSupply:4.5 Wper1 line,10 Wper4 lines (BRI4)

4.5 Wper1 line, 20 Wper4 lines (BRI8)

PowerSupplyMethod: Phantom PowerSupply

DoorOpenerCurrent Limit 24 VDC/30 VAC, 1 Amaximum

Paging Terminal Impedance 600

MOH (Music on Hold) Terminal

Impedance 10000

4.3. SYSTEMCAPACITY

4.3.1. MaximumTrunkand Extension Cards

The following numberof trunk and extension cards canbe installedinthe HybridIP-PBXfor

expansion.

CardType KX-TDA100

Trunk Card*1 4

Extension Card 4

Total 5

*1 One T1, E1, PRI30 and PRI23 cardcounts as 2 cards.

Note:

-For eachcard, amaximum numberthat canbeinstalledinthe

HybridIP-PBX islistedin"Installation Manual".

-Anycard that exceedsthecapacityoftheHybridIP-PBX will be

ignored.

-WhentheHybridIP-PBX starts up withaninvalidconfiguration

mode, somecardswill beignored.

4.3.2. MaximumTerminal Equipment

The following numberof terminal equipment canbe supportedbythe HybridIP-PBX.

Terminal Equipment Type KX-TDA100

Telephone *1 64

CS 16

PS 128

Voice Mail 2

Doorphone 8

DoorOpener 8

*1 WhenonlyT76xx series and T7560, T7565 DPTs and SLTs are connected. IfotherDPTs or

APTs are connected, the maximum numberwill decrease as eachof these units is countedas 4

sets of SLTs orDPTs (T76xx series and T7560, T7565).

4.3.3. Power SupplyUnitSelection

HybridIP-PBXneeds anoptional powersupplyunit(PSU)suitable forits configuration.

Calculate the amount of "loadfigures"from the type and numberof equipment to be connected,

and determine the type of PSU thatwill be required.

LoadFigure Calculation

Equipment Type Load

Figure

PT DPT(T76xx series and

T7560, T7565) 1

OtherDPT/APT/DSS Console 4

Extension Card*1 DHLC8 8

SLC8 8

SLC16 16

MSLC16 16

CS 4

ISDN Extension 2

Voice Mail 1

*1 Onlythe extension cards thatcansupportSLTs count forthe loadfigures.

PSU Capability

EachPSU supports a different amount of loadfigures.

PSU Type Maximum LoadFigures

PSU-S 64

PSU-M*2 128

*2 Available forthe KX-TDA100 and KX-TDA200.

5. SYSTEMOVERVIEW

5.1. SYSTEMCONFIGURATIONS

5.2. SYSTEMCOMPONENTS

Model CardName Description

Shelves KX-

TDA100AL Basic Shelf

MainProcessing

Card MPR MainProcessing Card

MPR Option Card KX-

TDA0196XJ RMT Remote Card

COLine Cards KX-

TDA0180AL

KX-

TDA0181AL

KX-

TDA0184AL

KX-

TDA0188XJ

KX-

TDA0189XJ

KX-

TDA0193XJ

KX-

TDA0284XJ

KX-

TDA0288XJ

KX-

TDA0290CJ

KX-

TDA0480X

LCO8

LCOT16

E&M8

CID/PAY8

CID8

BRI4

BRI8

PRI30

IP-GW4

8-PortAnalogue Trunk Card

16-PortAnalogue Trunk Card

8-PortE&MTrunk Card

E-1 Trunk Card

8-PortCallerID/PayTone Card

8-PortCallerID Card

4-PortBRI Card

8-PortBRI Card

PRI Card

4-Channel VoIPGatewayCard

Extension Cards KX-

TDA0144XJ

KX-

TDA0170XJ

KX-

TDA0171XJ

KX-

TDA0172XJ

KX-

TDA0173XJ

KX-

TDA0174XJ

KX-

TDA0175XJ

CSIF8

DHLC8

DLC8

DLC16

SLC8

SLC16

MSLC16

8 Cell Station Interface Card

8-PortDigital HybridExtension Card

8-PortDigital Extension Card

16-PortDigital Extension Card

8-PortSingle Line Telephone Extension Card

16-PortSingle Line Telephone Extension Card

16-PortSingle Line Telephone Extension with

Message

Lamp Card

Inhaltsverzeichnis

Andere Panasonic Telefonanlage Handbücher

Panasonic

Panasonic KX-TDA30 Betriebsanleitung

Panasonic

Panasonic HYBRID IP-PBX KX-TDA100 Bedienungsanleitung

Panasonic

Panasonic KX-TDA150 Bedienungsanleitung

Panasonic

Panasonic KX-TDE100 Betriebsanleitung

Panasonic

Panasonic KX-NS300 Bedienungsanleitung

Panasonic

Panasonic KX-TDE100 Bedienungsanleitung

Panasonic

Panasonic KX-TD500 Bedienungsanleitung

Panasonic

Panasonic KX- TAW848 Bedienungsanleitung

Panasonic

Panasonic KX-TD1232 Fehlerbehebungshandbuch

Panasonic

Panasonic KX-NS500 Betriebsanleitung

Panasonic

Panasonic KX-TVP200 Bedienungsanleitung

Panasonic

Panasonic KX-NS1000 Bedienungsanleitung

Panasonic

Panasonic HYBRID IP-PBX KX-TDA200 Technisches Datenblatt

Panasonic

Panasonic KX-TDA50 Betriebsanleitung

Panasonic

Panasonic KX-TVS50 - 2 Port Voicemail System Bedienungsanleitung

Panasonic

Panasonic HYBRID IP-PBX KX-TDA100 Bedienungsanleitung

Panasonic

Panasonic KX-TD1232 Bedienungsanleitung

Panasonic

Panasonic KX-TDA600BX Bedienungsanleitung

Panasonic

Panasonic KX-HTS824 Bedienungsanleitung

Panasonic

Panasonic KX-TD816 Bedienungsanleitung

Panasonic

Panasonic KX-TDE100 Bedienungsanleitung

Panasonic

Panasonic KX-TDE100 Montage- und Wartungsanleitung

Panasonic

Panasonic KX-HTS824 Bedienungsanleitung

Panasonic

Panasonic KX-TDA30 Technisches Datenblatt

Beliebte Telefonanlage Handbücher anderer Marken

Allo.com

Allo.com Nano 2 Bedienungsanleitung

ZYCOD

ZYCOD ZX50 Bedienungsanleitung

LV switch

LV switch IPPBX800 Gebrauchsanweisung

Edge-Core

Edge-Core VST3305 Bedienungsanleitung

Rauland-Borg

Rauland-Borg Telecenter IV Bedienungsanleitung

Grandstream Networks

Grandstream Networks UCM6208 Bedienungsanleitung

ATCOM

ATCOM IPPBX IP02 Bedienungsanleitung

bintec elmeg

bintec elmeg elmeg hybird 600 Bedienungsanleitung

MCK

MCK EXTender PBXgateway Bedienungsanleitung

NEC

NEC SL1000 Bedienungsanleitung

Epygi

Epygi Quadro Quadro 2xi Bedienungsanleitung

SMC Networks

SMC Networks TigerVoIP SMCPBX10 Bedienungsanleitung

AGFEO

AGFEO AC 14 analog Bedienungsanleitung

Nortel

Nortel QSY22 Bedienungsanleitung

Epygi

Epygi Quadro Quadro 4xa Bedienungsanleitung

Samsung

Samsung NX-308 Bedienungsanleitung

SpectraLink

SpectraLink Link 3000 Handbuch

Allo.com

Allo.com Nano 2 Bedienungsanleitung