Panasonic TH-46PZ81FV Bedienungsanleitung

Unauthorized copying and distribution is a violation

of law.

ORDER NO. PCZ0811192CE

Plasma Television

Model No. TH-46PZ81FV

GPF11DE Chassis

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.2. Touch-Current Check

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground

such as a water pipe, as shown in Figure 1.

3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reserve the AC plug in the AC outlet and repeat each of the above measure.

6. The potential at any point (TOUGH CURRENT) expressed as voltage U1and U2, does not exceed the following values:

For a. c.: U1= 35 V (peak) and U2= 0.35 V (peak);

For d. c.: U1= 1.0 V,

Note:

The limit value of U2= 0.35 V (peak) for a. c. and U1= 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0

mA d. c.

The limit value U1= 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.

7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be

repaired and rechecked before it is returned to the customer.

Figure 1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-

ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient

to damage an ES device).

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d

suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please

use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-

der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the

opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-

ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

3 Service Navigation

3.1. Service Hint

Board Name Function Board Name Function

P Power Supply C1 Data Driver (Lower Right)

A DC-DC Converter

Speaker out, Sound Processor

AV Terminal, AV Switch

Digital Signal Processor, MPU, HDMI Interface

Peaks Lite 2p, Fan control

C2 Data Driver (Lower Center)

C3 Data Driver (Lower Left)

SC Scan Drive

SU Scan out (Upper)

SD Scan out (Lower)

D Format Converter, Plasma AI, Sub-Field Processor SS Sustain Drive

K Remote receiver, Power LED GH HDMI3 in

S Power Switch G Front Terminal, Key Switch

GS SD Card Slot

3.2. Applicable signals

4 Specifications

Note

• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.

• This equipment complies with the EMC standards listed below.

EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.

Power Source AC 220 - 240 V, 50/60 Hz

Power Consumption

Average use 470 W

Standby condition 0.4 W (Without monitor out recording)

20 W (With monitor out recording)

Plasma Display panel

Aspect Ratio 16:9

Visible screen size 117 cm (diagonal)

1,019 mm (W) ×573 mm (H)

Number of pixels 2,073,600 (1,920 (W) ×1,080 (H)) [5,760 ×1,080 dots]

Sound

Speaker 160 mm ×42 mm ×2 pcs, 8 Ω

Audio Output 20 W (10 W + 10 W), 10% THD

Headphones M3 (3.5 mm) stereo mini Jack ×1

PC signals VGA, SVGA, XGA

SXGA ....... (compressed)

Horizontal scanning frequency 31 - 69 kHz

Vertical scanning frequency 59 - 86 Hz

Receiving Systems / Band name PAL B, G, H, I, SECAM B, G, SECAM L/L’ :

VHF E2 - E12 VHF H1 - H2 (ITALY)

VHF A - H (ITALY) UHF E21 - E69

CATV (S01 - S05) CATV S1 - S10 (M1 - M10)

CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)

PAL D, K, SECAM D, K :

VHF R1 - R2 VHF R3 - R5

VHF R6 - R12 UHF E21 -E69

PAL 520/60 : Playback of NTSC tape from some PAL Video recorders (VCR)

DVB : Digital terrestrial services via VHF / UHF aerial input.

M.NTSC : Playback from M. NTSC Video recorders (VCR)

NTSC (AV input only) : Playback from NTSC Video recorders (VCR)

TV signals may not be received in some areas.

Aerial - Rear VHF/UHF

Operating Conditions

Temperature: 0 °C - 35 °C

Humidity: 20 % - 80 % RH (non-condensing)

Connection Terminals

AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)

AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)

AV3

VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)

S-VIDEO Mini DIN 4-pin Y:1.0 V [p-p] (75 Ω) C:0.286 V [p-p] (75 Ω)

AUDIO L - R RCA PIN Type ×2 0.5 V [rms]

COMPONENT

VIDEO Y 1.0 V [p-p] (including synchronization)

PB, PR± 0.35 V [p-p]

AUDIO L - R RCA PIN Type ×2 0.5 V [rms]

Others

HDMI1 / 2 / 3 TYPE A Connectors This TV supports “HDAVI Control 3” function.

PC HIGH-DENSITY D-SUB 15PIN R, G, B/ 0.7 V [p-p] (75 Ω)

HD, VD/TTL Level 2.0 - 5.0 V [p-p] (high impedance)

Card slot SD Card slot ×1

Output

AUDIO L - R RCA PIN Type ×2 0.5 V [rms] (high impedance)

DIGITAL AUDIO OUT PCM/Dolby Digital/DTS, Fiber optic

Dimensions (W ×H ×D) 1,158 mm ×800 mm ×387 mm (With Pedestal)

1,158 mm ×747 mm ×99.7 mm (TV only)

Mass 40.0 kg Net (With Pedestal)

35.0 kg Net (TV only)

5 Service Mode

5.1. How to enter into Service Mode

While pressing [VOLUME ( - )] button of the main unit, press [0] button of the remote control three times within 2 seconds.

5.1.1. Key command

[1] button...Main items Selection in forward direction

[2] button...Main items Selection in reverse direction

[3] button...Sub items Selection in forward direction

[4] button...Sub items Selection in reverse direction

[RED] button...All Sub items Selection in forward direction

[GREEN] button...All Sub items Selection in reverse direction

[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )

5.1.2. Contents of adjustment mode

• Value is shown as a hexadecimal number.

• Preset value differs depending on models.

• After entering the adjustment mode, take note of the value in each item before starting adjustment.

5.1.3. How to exit

Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.

5.2. Service tool mode

5.2.1. How to access

1. Select [SRV-TOOL] in Service Mode.

2. Press [OK] button on the remote control.

5.2.2. Display of SOS History

SOS History (Number of LED blinking) indication.

From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.

This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory ship-

ment setting].

5.2.3. POWER ON TIME/COUNT

To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.

Time : Cumulative power on time, indicated hour : minute by decimal

Count : Number of ON times by decimal

Note : This indication will not be cleared by either of the self-checks or any other command.

5.2.4. Exit

1. Disconnect the AC cord from wall outlet or switch off the power with the [POWER] button on the main unit.

Inhaltsverzeichnis

Andere Panasonic Plasma-TV Handbücher

Panasonic

Panasonic Viera Link TH-42PZ80U Bedienungsanleitung

Panasonic

Panasonic TH-P54Z1D Bedienungsanleitung

Panasonic

Panasonic TCP54VT25 - 54" PLASMA 3D TV Bedienungsanleitung

Panasonic

Panasonic TH42PD60X - 42" SD PDP TV Bedienungsanleitung

Panasonic

Panasonic Viera TH-42PZ85E Bedienungsanleitung

Panasonic

Panasonic Viera TH-P50VT20D Bedienungsanleitung

Panasonic

Panasonic Viera TH-P42S10D Bedienungsanleitung

Panasonic

Panasonic TH-50PF20U Einrichtungshandbuch

Panasonic

Panasonic Viera TC-P50UT50 Bedienungsanleitung

Panasonic

Panasonic TCP60ST50X Bedienungsanleitung

Panasonic

Panasonic Viera TC-L32X2 Bedienungsanleitung

Panasonic

Panasonic TH42PV500EY Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42X1 Bedienungsanleitung

Panasonic

Panasonic TH-42PWD3 Bedienungsanleitung

Panasonic

Panasonic Viera TH-37PV70EY Bedienungsanleitung

Panasonic

Panasonic TH37PR10UA - HD PLASMA DISPLAY Bedienungsanleitung

Panasonic

Panasonic Viera TH-42PX75U Bedienungsanleitung

Panasonic

Panasonic TH-42PV700F Bedienungsanleitung

Panasonic

Panasonic TC P50G10 - TC - 49.9" Plasma TV Bedienungsanleitung

Panasonic

Panasonic VIERA TH-42PV30A Bedienungsanleitung

Panasonic

Panasonic TH-65PV500B Bedienungsanleitung

Panasonic

Panasonic TH-42PX20U/P Operating Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42X1 Bedienungsanleitung

Panasonic

Panasonic TH-P42UT30A Bedienungsanleitung

Beliebte Plasma-TV Handbücher anderer Marken

Hitachi

Hitachi 50PD9800TA Bedienungsanleitung

LG 60PA5500 Bedienungsanleitung

Sony

Sony WEGA KE-P42M1 Bedienungsanleitung

VESTEL

VESTEL PL2000 Bedienungsanleitung

VisionQuest

VisionQuest PVQ-32VGB Bedienungsanleitung

Maxent

Maxent MX-5020HPM Bedienungsanleitung

LG 50PK550 Bedienungsanleitung

LG PJ550N Bedienungsanleitung

Samsung

Samsung PA43H4000 Bedienungsanleitung

LG 42LG70ER Bedienungsanleitung

Samsung

Samsung 7+ series Bedienungsanleitung

LG DU-42PZ60H Bedienungsanleitung

Nexus

Nexus NX422 Bedienungsanleitung

JVC

JVC AV42PD20ES Bedienungsanleitung

Samsung

Samsung PS42A466P2M Bedienungsanleitung

Samsung

Samsung PL42E7SX/RCL Bedienungsanleitung

Samsung

Samsung PS-42D4S Kurzanleitung

Samsung

Samsung PS43F4900 Bedienungsanleitung