Panasonic TH-C46FD18A Bedienungsanleitung

rights reserved. Unauthorized copying and distribu-

tion is a violation of law.

ORDER NO. MTNC080960CE

B34 Canada: B07

46 inch Class 1080p Plasma HDTV

Model No. TH-C46FD18A

GPF11DU Chassis

1 Safety Precautions

1.1. General Guidelines

1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the

wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.

3. When conducting repairs and servicing, do not twist the Faston connectors but plug them straight in or unplug them straight

out.

4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-

lic cabinet part on the equipment such as screwheads,

connectors, control shafts, etc. When the exposed metal-

lic part has a return path to the chassis, the reading

should be between 1Mohm and 5.2Mohm.

When the exposed metal does not have a return path to

the chassis, the reading must be .

1.1.2. Leakage Current Hot Check (See

Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5kohm, 10 watts resistor, in parallel with a

0.15μF capacitors, between each exposed metallic part

on the set and a good earth ground such as a water pipe,

as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensi-

tivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliamp. In case a measure-

ment is outside of the limits specified, there is a possibility

of a shock hazard, and the equipment should be repaired

and rechecked before it is returned to the customer.

Figure 1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-

ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient

to damage an ES device).

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d

suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please

use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-

der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the

opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-

ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

3 Service Navigation

3.1. Important Notice

3.1.1. MANUFACTURING ID NO.

This service manual is for MANUFACTURING ID NO. TH-C46FD18A as indicated in the label at side and the model name plate of

the unit.

3.2. Different P.C.B.

Parts No. Parts name & Description Remarks

TH-C46FD18 TH-C46FD18A

TNPH0721AMS TNPH0721APS CIRCUIT BOARD A PAVCA

TNPA4243AES TNPA4243ABS CIRCUIT BOARD PB PAVCA

ETX2MM704MGB CIRCUIT BOARD P (AC) PAVCA

ETX2MM704MGH CIRCUIT BOARD P (MAIN) PAVCA

TNPA4439AKS TNPA4439BKS CIRCUIT BOARD D PAVCA

TNPA4501S CIRCUIT BOARD G PAVCA

TNPA4603ABS CIRCUIT BOARD GH PAVCA

TNPA4139ADS CIRCUIT BOARD GS PAVCA

TNPA4500S CIRCUIT BOARD K PAVCA

TNPA4499S CIRCUIT BOARD S PAVCA

TXNC11RKTC CIRCUIT BOARD C1 PAVCA

TXNC21RKTC CIRCUIT BOARD C2 PAVCA

TXNC31RKTC CIRCUIT BOARD C3 PAVCA

TXNSC1RKTC TXNSC1BJUC CIRCUIT BOARD SC PAVCA

TXNSD1RKTC CIRCUIT BOARD SD PAVCA

TXNSS1RKTC TXNSS1BJUC CIRCUIT BOARD SS PAVCA

TXNSU1RKTC CIRCUIT BOARD SU PAVCA

3.3. Service Hint

Board Name Function Board Name Function

P Power Supply C1 Data Driver (Lower Right)

A DC-DC Converter

Speaker out, Sound Processor

AV Terminal, AV Switch

Digital Signal Processor, Micom, HDMI Interface

Peaks Lite 2p

C2 Data Driver (Lower Center)

C3 Data Driver (Lower Left)

SC Scan Drive

SU Scan out (Upper)

SD Scan out (Lower)

D Format Converter, Plasma AI, Sub-Field Processor SS Sustain Drive

K Remote receiver, Power LED GH HDMI3 in

S Power Switch G Front Terminal, Key Switch

GS SD Card Slot PB Fan control

3.4. Applicable signals

* Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC

Note

• Signals other than above may not be displayed properly.

• The above signals are reformatted for optimal viewing on your display.

horizontal frequency (kHz) vertical frequency (Hz) COMPONENT HDMI PC

525 (480) / 60i 15.73 59.94 * *

525 (480) /60p 31.47 59.94 * *

750 (720) /60p 45.00 59.94 * *

1,125 (1,080) /60i 33.75 59.94 * *

1,125 (1,080) /60p 67.43 59.94 *

1,125 (1,080) /60p 67.50 60.00 *

1,125 (1,080) /24p 26.97 23.98 *

1,125 (1,080) /24p 27.00 24.00 *

640 ×400 @70 31.47 70.08 *

640 ×480 @60 31.47 59.94 *

Macintosh 13 inch (640 ×480) 35.00 66.67 *

640 ×480 @75 37.50 75.00 *

852 ×480 @60 31.47 59.94 *

800 ×600 @60 37.88 60.32 *

800 ×600 @75 46.88 75.00 *

800 ×600 @85 53.67 85.08 *

Macintosh 16 inch (832 ×624) 49.73 74.55 *

1,024 ×768 @60 48.36 60.00 *

1,024 ×768 @70 56.48 70.07 *

1,024 ×768 @75 60.02 75.03 *

1,024 ×768 @85 68.68 85.00 *

Macintosh 21 inch (1,152 ×870) 68.68 75.06 *

1,280 ×1,024 @60 63.98 60.02 *

1,366 ×768 @60 48.36 60.00 *

4 Specifications

Power Source AC 120 V, 60 Hz

Power Consumption

Maximum 628 W

Standby condition 0.2 W

Plasma Display panel

Drive method AC type

Aspect Ratio 16:9

Visible screen size 46 inch class (46.0 inches measured diagonally)

(W ×H ×Diagonal) 40.1 inch ×22.5 inch ×46.0 inch (1,019 mm ×573 mm ×1,169 mm)

(No. of pixels) 2,073,600 (1,920 (W) ×1,080 (H))[5,760 ×1,080 dots]

Sound

Audio Output 20 W [ 10 W + 10 W ] ( 10 % THD )

PC signals VGA, SVGA, XGA, WXGA, SXGA

Horizontal scanning frequency 31 - 69 kHz

Vertical scanning frequency 59 - 86 Hz

Channel Capability (Digital/Analog) VHF/ UHF: 2 - 69, CATV: 1 - 135

Operating Conditions

Temperature: 32 °F - 104 °F (0 °C - 40 °C)

Humidity: 20 % - 80 % RH (non-condensing)

Connection Terminals

VIDEO IN 1-2 VIDEO: RCA PIN Type ×1 1.0 V [p-p] (75 Ω)

S-VIDEO: Mini DIN 4-pin Y: 1.0 V [p-p] (75 Ω) C: 0.286 V [p-p] (75 Ω)

AUDIO L-R: RCA PIN Type ×2 0.5 V [rms]

COMPONENT INPUT 1-2 Y: 1.0 V [p-p] (including synchronization)

PB, PR: ±0.35 V [p-p]

AUDIO L-R: RCA PIN Type ×2 0.5 V [rms]

HDMI 1-3 TYPE A Connector ×3

This TV supports [HDAVI Control 3] function.

PC D-SUB 15PIN: R,G,B / 0.7 V [p-p] (75 Ω)

HD, VD / 1.0 - 5.0 V [p-p] (high impedance)

AUDIO L-R: Stereo Mini Jack ( 3.5 mm) ×1

Card slot SD CARD slot ×1

AV PROG OUT VIDEO: RCA PIN Type ×1 1.0 V [p-p] (75 Ω)

AUDIO L-R: RCA PIN Type ×2 0.5 V [rms]

DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber Optic

FEATURES 3D Y/C FILTER

CLOSED CAPTION V-Chip

Photo Viewer HDAVI Control 3

Dimensions (W ×H ×D)

Including pedestal 44.3 inch ×31.6 inch ×15.3 inch (1,124 mm ×800.5 mm ×387 mm)

TV Set only 44.3 inch ×29.4 inch ×3.7 inch (1,124 mm ×746.5 mm ×92.5 mm)

Mass

Including pedestal 79.4 lb. (36.0 kg)

TV Set only 75.0 lb. (34.0 kg)

Note

• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.

5 Service Mode

5.1. How to enter into Service Mode

While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.

5.1.1. Key command

[1] button...Main items Selection in forward direction

[2] button...Main items Selection in reverse direction

[3] button...Sub items Selection in forward direction

[4] button...Sub items Selection in reverse direction

[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )

5.1.2. Contents of adjustment mode

• Value is shown as a hexadecimal number.

• Preset value differs depending on models.

• After entering the adjustment mode, take note of the value in each item before starting adjustment.

5.1.3. How to exit

Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.

Main item Sub item Sample Data Remark

ADJUST CONTRAST 000

COLOR 3C

TINT 03

SUB-BRT 800

WB-ADJ R-CUT 80

G-CUT 80

B-CUT 80

R-DRV FC

G-DRV F8

B-DRV D9

ALL-CUT 80

ALL-DRV FC

OPTION BOOT ROM Factory Preset

STBY-SET 00

EMERGENCY ON

CLK MODE 00

CLOCK 000

AGING RGBW

COUNT

ALL WHITE

ALL RED

ALL GREEN

ALL BLUE

ON/OFF

RAMP WHITE

RAMP RED

RAMP GREEN

RAMP BLUE

1% WINDOW

COLOR BAR

A-ZONE B-ZONE/4 TRIO

SCROLL

WHITE FLAME

RM-SET CODE A Fixed

SRV-TOOL - See next

Inhaltsverzeichnis

Andere Panasonic Plasma-TV Handbücher

Panasonic

Panasonic TH-42PV60A Bedienungsanleitung

Panasonic

Panasonic TH-42PX6U Bedienungsanleitung

Panasonic

Panasonic TH-37PA30 Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42S1 Bedienungsanleitung

Panasonic

Panasonic 50PZ700U - 50" Plasma TV Bedienungsanleitung

Panasonic

Panasonic Viera TX-P50G20ES Bedienungsanleitung

Panasonic

Panasonic VIERA TC-P55GT30 Bedienungsanleitung

Panasonic

Panasonic Viera TC-65PST34 Bedienungsanleitung

Panasonic

Panasonic TC-P65VT25 (English, Spanish) Bedienungsanleitung

Panasonic

Panasonic TH-50PV600AZ Bedienungsanleitung

Panasonic

Panasonic X50D series Bedienungsanleitung

Panasonic

Panasonic Viera TC-P50X20P Bedienungsanleitung

Panasonic

Panasonic Viera TX-P42ST50Y Bedienungsanleitung

Panasonic

Panasonic TH-103PF9UK - 103" Plasma Panel Kurzanleitung

Panasonic

Panasonic Viera TH-37PX60B Bedienungsanleitung

Panasonic

Panasonic TXP65VT60Y Bedienungsanleitung

Panasonic

Panasonic Viera TH-50PE8U Bedienungsanleitung

Panasonic

Panasonic VIERA TH-58PZ800U Bedienungsanleitung

Panasonic

Panasonic TCP50U2 - 50" PLASMA TV Bedienungsanleitung

Panasonic

Panasonic TC-P42U1 - 42" Plasma TV Bedienungsanleitung

Panasonic

Panasonic Viera U50A series Bedienungsanleitung

Panasonic

Panasonic VIERA TH-42PZ800U Bedienungsanleitung

Panasonic

Panasonic viera TH-P54V20A Bedienungsanleitung

Panasonic

Panasonic MBS0407S0 Bedienungsanleitung

Beliebte Plasma-TV Handbücher anderer Marken

Hitachi

Hitachi 50PD9800TA Bedienungsanleitung

Pioneer

Pioneer PDP-LX508G Bedienungsanleitung

LG 60PM9700 Bedienungsanleitung

LG 50PX4D Bedienungsanleitung

LG 60PA5500 Bedienungsanleitung

Sony

Sony WEGA KE-P42M1 Bedienungsanleitung

VESTEL

VESTEL PL2000 Bedienungsanleitung

VisionQuest

VisionQuest PVQ-32VGB Bedienungsanleitung

Maxent

Maxent MX-5020HPM Bedienungsanleitung

XOCECO

XOCECO PH-42T8 Bedienungsanleitung

Maxent

Maxent MX-42VM7 Bedienungsanleitung

Sampo

Sampo PME-42S6 Bedienungsanleitung

Hitachi

Hitachi 32PD7800 Bedienungsanleitung

LG 50PK550 Bedienungsanleitung

Haier

Haier P42A1-AK Bedienungsanleitung

Insignia

Insignia NS-42P650A11 Bedienungsanleitung

Hitachi

Hitachi 42PD3200A Bedienungsanleitung

LG 50PS70FD-AA Bedienungsanleitung