Panasonic Viera TC-P60UT50 Bedienungsanleitung

Unauthorized copying and distribution is a violation

of law.

ORDER NO.MTNC120451CE

B34 Canada: B62

60 inch Class 1080p Plasma HDTV

Model No. TC-P60UT50

GPF15DU Chassis

For detailed troubleshooting information and circuit explanations,

refer to the "QSM/Service Hints/Troubleshooting Information(TI)" and Seminar/Training Manual/Technical

Guide(TG) documents posted on the TSN web site.

For information about this model, type TC-P2012 in the model box under "Direct Search".

TABLE OF CONTENTS

PAGE PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3

2 Warning --------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------4

2.2. About lead free solder (PbF) ----------------------------5

3 Service Navigation------------------------------------------------6

3.1. PCB Layout --------------------------------------------------6

4 Specifications ------------------------------------------------------7

5 Technical Descriptions------------------------------------------8

5.1. Specification of KEY for DTCP-IP, WMDRM

and Widevine------------------------------------------------8

6 Service Mode -------------------------------------------------------9

6.1. How to enter into Service Mode ------------------------9

6.2. Option - Mirror--------------------------------------------- 11

6.3. Service tool mode ---------------------------------------- 11

6.4. Hotel mode------------------------------------------------- 12

6.5. Data Copy by SD Card --------------------------------- 13

7 Troubleshooting Guide---------------------------------------- 16

8 Service Fixture & Tools --------------------------------------- 17

8.1. SC jig -------------------------------------------------------- 17

9 Disassembly and Assembly Instructions --------------- 18

9.1. Disassembly Flow Chart for the Unit ---------------- 18

9.2. Disassembly Procedure for the Unit----------------- 19

10 Measurements and Adjustments -------------------------- 25

10.1. Adjustment ------------------------------------------------- 25

11 Block Diagram --------------------------------------------------- 27

11.1. Main Block Diagram ------------------------------------- 27

11.2. Block (1/4) Diagram ------------------------------------- 28

11.3. Block (2/4) Diagram ------------------------------------- 29

11.4. Block (3/4) Diagram ------------------------------------- 30

11.5. Block (4/4) Diagram ------------------------------------- 31

12 Wiring Connection Diagram--------------------------------- 33

12.1. Caution statement.--------------------------------------- 33

12.2. Wiring (1) --------------------------------------------------- 33

12.3. Wiring (2) --------------------------------------------------- 34

12.4. Wiring (3) --------------------------------------------------- 35

12.5. Wiring (4) --------------------------------------------------- 36

12.6. Wiring (5) --------------------------------------------------- 37

13 Schematic Diagram

14 Printed Circuit Board

15 Exploded View

1 Safety Precautions

1.1. General Guidelines

1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the

wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.

3. When conducting repairs and servicing, do not twist the Fasten connectors but plug them straight in or unplug them straight

out.

4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed

metallic cabinet part on the equipment such as

screwheads, connectors, control shafts, etc. When the

exposed metallic part has a return path to the chassis, the

reading should be between 1Mohm and 5.2Mohm.

When the exposed metal does not have a return path to

the chassis, the reading must be .

1.1.2. Leakage Current Hot Check (See

Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5kohm, 10 watts resistor, in parallel with a

0.15μF capacitors, between each exposed metallic part

on the set and a good earth ground such as a water pipe,

as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more

sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the

voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliamp. In case a

measurement is outside of the limits specified, there is a

possibility of a shock hazard, and the equipment should

be repaired and rechecked before it is returned to the

customer.

Figure 1

2 Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or

comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)

sufficient to damage an ES device).

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it's manufacture due to environmental conservation issues. For service and repair work, we'd

suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please

use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb

solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the

opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.

However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

3 Service Navigation

3.1. PCB Layout

Board Name Function

P Power Supply

Non serviceable.

P-Board should be exchanged for service.

A Main AV input, processing

K Remote receiver, Power LED, C.A.T.S sensor

C1 Data Driver (Lower Right)

C2 Data Driver (Lower Center)

C3 Data Driver (Lower Left)

SC Scan Drive

SS Sustain Drive

SS2 Sustain out (Lower)

SU Scan out (Upper)

Non serviceable.

SU-Board should be exchanged for service.

SD Scan out (Lower)

Non serviceable.

SD-Board should be exchanged for service.

4 Specifications

QTV

QBluetooth

Note

Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.

Power Source AC 120 V, 60 Hz

Power Consumption

Rated Power 427 W

Standby Power 0.2 W

Display Panel

Panel System Plasma Display panel

Screen size 60 inch class (60.1 inches measured diagonally)

W ×H ×Diagonal 52.3 inch ×29.4 inch ×60.1 inch (1,330 mm ×748 mm ×1,526 mm)

Number of pixels 1,920 ×1,080

Speaker Output 20 W [10 W + 10 W] (10 % THD)

Channel Capability (Digital/Analog) VHF/ UHF: 2 - 69, CATV: 1 - 135

Operating Conditions

Temperature: 32 °F - 104 °F (0 °C - 40 °C)

Humidity: 20 % - 80 % RH (non-condensing)

Connection Terminals

VIDEO IN RCA PIN (VIDEO, AUDIO-L, AUDIO-R)

COMPONENT IN RCA PIN (Y, PB, PR, AUDIO-L, AUDIO-R)

HDMI IN 1/2 TYPE A Connector (supports [HDAVI Control 5] function)

USB 1/2 USB2.0 Type A connector

DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber Optic

OTHERS SD CARD slot, ETHERNET (10BASE-T/100BASE-TX)

Dimensions (W ×H ×D)

Including pedestal 55.2 inch ×34.8 inch ×15.3 inch (1,401 mm ×883 mm ×387 mm)

TV Set only 55.2 inch ×32.9 inch ×3.3 inch (1,401 mm ×835 mm ×84 mm)

Mass

Including pedestal 83.8 lb. (38.0 kg) NET

TV Set only 73.9 lb. (33.5 kg) NET

Standard Compliance Bluetooth®3.0

Frequency Range 2.402GHz~2.480GHz

• Use Panasonic 3D Eyewear supporting Bluetooth wireless technology.

5 Technical Descriptions

5.1. Specification of KEY for DTCP-IP, WMDRM and Widevine

5.1.1. General information:

1. EEPROM (IC8902) for spare parts has the seed of KEY for each DTCP-IP for DLNA, WMDRM for Netflix and Widevine for

CinemaNow.

2. The final KEY data will be generated by Peaks IC (IC8000) when SELF CHECK was done and are stored in both Peaks IC

(IC8000) and EEPROM (IC8902).

5.1.2. Replacement of ICs:

When Peaks IC is replaced, EEPROM should be also replaced with new one the same time.

When EEPROM is replaced, Peaks IC is not necessary to be replaced the same time.

After the replacement of IC, SELF CHECK should be done to generate the final KEY data.

How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for

more than 3 seconds.

TV will be forced to the factory shipment setting after this SELF CHECK.

6 Service Mode

6.1. How to enter into Service Mode

6.1.1. Purpose

After exchange parts, check and adjust the contents of adjustment mode.

While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds

Note:

Service Mode can not be entered when 3D signal input.

Input 2D signal to enter Service Mode.

6.1.2. Key command

[1] button...Main items Selection in forward direction

[2] button...Main items Selection in reverse direction

[3] button...Sub items Selection in forward direction

[4] button...Sub items Selection in reverse direction

[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )

6.1.3. How to exit

Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.

6.1.4. Contents of adjustment mode

• Value is shown as a hexadecimal number.

• Preset value differs depending on models.

• After entering the adjustment mode, take note of the value in each item before starting adjustment.

Main item Sub item Sample Data Remark

ADJUST CONTRAST 000

COLOR 3C

TINT 00

SUB-BRT 800

WB-ADJ R-CUT 80

G-CUT 80

B-CUT 80

R-DRV DF

G-DRV FF

B-DRV 7C

ALL-CUT 80

ALL-DRV FF

OPTION Boot ROM Factory Preset

STBY-SET 00

EMERGENCY OFF

CLK MODE 00

CLOCK 000

EDID-CLK HIGH

MIRROR 00 (See Option-Mirror)

VSUS LOW See Vsus selection

AGING ALL WHITE Built-in test patterns can be

displayed.

MIDDLE BLUE WITH MAGENTA OUTSIDE FRAME

MIDDLE STEP GREEN

MIDDLE STEP RED

LOW STEP WHITE

ALL BLUE

ALL GREEN

ALL RED

WHITE DIAGONAL STRIPE

RED DIAGONAL STRIPE

GREEN DIAGONAL STRIPE

BLUE DIAGONAL STRIPE

A-ZONE & B-ZONE

1% WINDOW

COLOR BAR

9 POINTS BRIGHT MEASURE

2 DOT OUTSIDE FRAME

DOUBLE FIXED 1% WINDOW

VERTICAL LINE SCROLL

ON/OFF

R/G/B/W ROTATION WITH COUNT DISPLAY

HALF FIXED ALL WHITE

ALL WHITE WITH COUNT DISPLAY

SRV-TOOL 00 See Service tool mode

Andere Handbücher für Viera TC-P60UT50

Inhaltsverzeichnis

Andere Panasonic Plasma-TV Handbücher

Panasonic

Panasonic Viera TC-P55ST30 Bedienungsanleitung

Panasonic

Panasonic TC-P50U20P Bedienungsanleitung

Panasonic

Panasonic TC-P42G10 - TC - 41.6" Plasma TV Bedienungsanleitung

Panasonic

Panasonic TC-42PX14 - 42" Plasma Panel Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42S1 Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42U2 Bedienungsanleitung

Panasonic

Panasonic Viera TC-42PX34X Bedienungsanleitung

Panasonic

Panasonic TC-P50VT25 Bedienungsanleitung

Panasonic

Panasonic TC-P42X60 Bedienungsanleitung

Panasonic

Panasonic TCP50U2 - 50" PLASMA TV Bedienungsanleitung

Panasonic

Panasonic Viera TH-42PZ8B Bedienungsanleitung

Panasonic

Panasonic TC-P58S1 - 58" Plasma TV Einrichtungshandbuch

Panasonic

Panasonic Viera TH-P42V20A Bedienungsanleitung

Panasonic

Panasonic Viera TH-P42ST30Z Bedienungsanleitung

Panasonic

Panasonic TC-P42C1 - 41.6" Plasma TV Bedienungsanleitung

Panasonic

Panasonic TC-P42C1 - 41.6" Plasma TV Bedienungsanleitung

Panasonic

Panasonic Viera TH-50PZ700B Bedienungsanleitung

Panasonic

Panasonic TXP65VT60Y Bedienungsanleitung

Panasonic

Panasonic TX-PR37C10 Bedienungsanleitung

Panasonic

Panasonic Viera TX-P42G10E Bedienungsanleitung

Panasonic

Panasonic TH-37PW4 Bedienungsanleitung

Panasonic

Panasonic Viera TC-P50U50 Bedienungsanleitung

Panasonic

Panasonic Viera TX-P42S20E Bedienungsanleitung

Panasonic

Panasonic Viera TC-P42G25 Einrichtungshandbuch

Beliebte Plasma-TV Handbücher anderer Marken

Hitachi

Hitachi 50PD9800TA Bedienungsanleitung

LG 60PA5500 Bedienungsanleitung

Sony

Sony WEGA KE-P42M1 Bedienungsanleitung

VESTEL

VESTEL PL2000 Bedienungsanleitung

VisionQuest

VisionQuest PVQ-32VGB Bedienungsanleitung

Maxent

Maxent MX-5020HPM Bedienungsanleitung

LG 50PK550 Bedienungsanleitung

LG PJ550N Bedienungsanleitung

Samsung

Samsung PA43H4000 Bedienungsanleitung

LG 42LG70ER Bedienungsanleitung

Samsung

Samsung 7+ series Bedienungsanleitung

LG DU-42PZ60H Bedienungsanleitung

Nexus

Nexus NX422 Bedienungsanleitung

JVC

JVC AV42PD20ES Bedienungsanleitung

Samsung

Samsung PS42A466P2M Bedienungsanleitung

Samsung

Samsung PL42E7SX/RCL Bedienungsanleitung

Samsung

Samsung PS-42D4S Kurzanleitung

Samsung

Samsung PS43F4900 Bedienungsanleitung