Panasonic EYFME1C Bedienungsanleitung

Unauthorized copying and distribution is a violation

of law.

Order Number PTD1710E39CE

Cordless Right Angle Impact

Model No. EYFME1C

Europe

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 6

5 Appendix -----------------------------------------------------------11

6 Exploded View and Replacement Parts List -----------12

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please

use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-

ing iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).

2 Specifications

3 Troubleshooting Guide

3.1. Troubleshooting Guide

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A and B by pinching lead wires.

• There is no dust or deformation on battery terminals.

3.2.2. Operation

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Check whether the tool operates properly in both the forward and reveres directions.

• Set the LED light to switch-linked mode (L2) and check whether the LED light turns on when the trigger is engaged and that it

turns off when the trigger is released.

• Set the buzzer to each of its three modes and verify that there is no buzzer in b0 mode, that the buzzer sounds when the green

lamp is on in b1 mode, and that the buzzer sounds when the Red lamp is on b2 mode.

• Check whether the ID setting has been properly configured after repair and reassembly.

[ Method of confirmation ]

1. Press D button on the remote control

2. Confirm the operation panel display

• Initializing all settings (revert settings to factory defaults).

[ Setting method ]

3.2.3. Integrity

• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.

4 Disassembly and Assembly Instructions

* To reduce the risk of injury, always remove battery pack before removing/installing the tool.

* To assemble the tool, start with 4-10 and proceed to 4-1.

4.1. How to remove the gear case assembly

4.2. How to remove the SQ bevel gear assembly and bevel pinion assembly

4.3. How to remove the housing B

4.4. How to remove assemblies

4.5. Precautions when removing the module assembly

4.6. Checking and setting the module assembly’s DIP switches

4.7. How to remove the anvil, anvil bushing, thrust plate and slider

4.8. How to remove the driving shaft assembly and motor mounting plate

assembly

4.9. How to remove the driving shaft assembly

4.10. Caution in replacing the switch (WEYFGA1NK207)

4.11. Wiring and Assembly Points

Inhaltsverzeichnis

Andere Panasonic Elektrowerkzeuge Handbücher

Panasonic

Panasonic EYFLC1A Bedienungsanleitung

Panasonic

Panasonic EYFMH1WC Bedienungsanleitung

Panasonic

Panasonic EYFEA1N Betriebsanleitung

Panasonic

Panasonic EYFLA4 Bedienungsanleitung

Panasonic

Panasonic 7552LJ Bedienungsanleitung

Panasonic

Panasonic EY4541 Bedienungsanleitung

Panasonic

Panasonic EY75A8 Bedienungsanleitung

Panasonic

Panasonic EY7541 - CORDLESS IMPACT WRENCH Bedienungsanleitung

Panasonic

Panasonic EYFPA1J Bedienungsanleitung

Panasonic

Panasonic EY4541 Bedienungsanleitung

Panasonic

Panasonic EY3640 Bedienungsanleitung

Panasonic

Panasonic EY3610 Bedienungsanleitung

Panasonic

Panasonic EYFPA1C Bedienungsanleitung

Panasonic

Panasonic 4541OLOA Bedienungsanleitung

Panasonic

Panasonic AccuPulse QP Low Noise Series Bedienungsanleitung

Panasonic

Panasonic EYFLA4A Bedienungsanleitung

Panasonic

Panasonic EYFLA4A Bedienungsanleitung

Panasonic

Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG Bedienungsanleitung

Panasonic

Panasonic EYFLA9C Bedienungsanleitung

Panasonic

Panasonic EY46A5 Bedienungsanleitung

Panasonic

Panasonic EY74A2 Bedienungsanleitung

Panasonic

Panasonic EY7552X57 Bedienungsanleitung

Panasonic

Panasonic EY4541 Bedienungsanleitung

Panasonic

Panasonic EY7550LR2S Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch