Panasonic PT-FX400 Bedienungsanleitung

SPEC FILE

Produc Number : PT-FX400

Produc Name : LCD Projector

As of March 2011. Specifica ions and appearance are subjec o change wi hou no ice.

SFL11M006-1

1/13

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

2/13

Specifications

Main unit

Power supply

Power consumption

LCD panel Panel size

Display method

Pixels

Pixel configuration

Lens

Throw ratio

Lamp

Screen size

Colors

Brightness*2

Center-to-corner uniformity*2

Contrast*2

Resolution

Scanning frequency HDMI/DVI-I (digital)

DVI-I (analog)/RGB

YPBPR(YCBCR)

Video/S-Video

Optical axis shift

Keystone correction range

Installation

Built-in speaker Size

Output power

Terminals HDMI IN

100–240 V AC, 3.9–1.4 A, 50/60 Hz

330 W

(0.3 W at 100–120 V AC, 0.4 W at 220–240 V AC when standby mode

set to eco,*19 W when standby mode set to normal, 20 W when

standby mode set to normal and audio monitor out.)

20.3 mm (0.8 inches) diagonal (4:3 aspect ratio)

Transparent LCD panel (× 3, R/G/B)

786,432 (1,024 × 768) × 3, total of 2,359,296 pixels

Stripe

Manual (2× zoom), manual focus F 1.7–2.6, f 24.0–47.2 mm

1.48–2.96:1

250 W UHM lamp

0.84–7.62 m (33–300 inches) diagonally, 4:3 aspect ratio

Full color (16,777,216 colors)

4,000 lumens

80%

600:1 (full on/full off)

1,024 × 768 pixels (Input signals that exceed this resolution will be

converted to 1,024 × 768 pixels.)

fH: 27.0 kHz–68.7 kHz, fV: 24.0 Hz–85.0 Hz,

dot clock: 25.2 MHz–148.5 MHz

fH: 15.6 kHz–91.1 kHz, fV: 24.0 Hz–85.1 Hz,

dot clock: 162 MHz or lower

480i (525i): fH15.75 kHz; fV60 Hz,

576i (625i): fH15.63 kHz; fV50 Hz,

480p (525p): fH31.50 kHz; fV60 Hz,

576p (625p): fH31.25 kHz; fV50 Hz,

720 (750)/60p: fH45.00 kHz; fV60 Hz,

720 (750)/50p: fH37.50 kHz; fV50 Hz,

1080 (1125)/60i: fH33.75 kHz; fV60 Hz,

1080 (1125)/50i: fH28.13 kHz; fV50 Hz,

1080 (1125)/24p: fH27.00 kHz; fV24 Hz,

1080 (1125)/60p: fH67.50 kHz; fV60 Hz,

1080 (1125)/50p: fH56.25 kHz; fV50 Hz

fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]

fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

Vertical: ±50% from center of screen (manual),

horizontal: ±27% from center of screen (manual)

Vertical: ±30°

Ceiling/desk, front/rear (menu selection)

4 cm (1-9/16 inches) (round) × 1

5.0 W (monaural)

HDMI 19-pin × 1, Deep Color, HDCP compatible

480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p,

1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p,

1080 (1125)/50p

VGA (640 × 480)–WSXGA+(1,680 × 1,050), compatible with non-

interlaced signals only, dot clock: 25.2 MHz–146.25 MHz

Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz,

32 kHz)

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

3/13

DVI-I IN*3

Digital

R, G, B

Y, PB(CB), PR(CR)

COMPUTER (RGB) IN

R, G, B

Y, PB(CB), PR(CR)

VIDEO IN

S-VIDEO IN

AUDIO IN 1

AUDIO IN 2

AUDIO IN 3

AUDIO OUT

SERIAL IN

LAN

WIRELESS MODULE

Power cord length

Cabinet materials

Dimensions (W × H × D)

Weight

Operation noise

Operating temperature

Operating humidity

Remote control unit

Power supply

Operation range*6

Dimensions (W × H × D)

Weight

Supplied accessories

DVI-I 29-pin × 1

DVI 1.0 compliant, compatible with HDCP, compatible with single link

only480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p,

1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p,

1080 (1125)/50p

VGA (640 × 480)–WSXGA+(1,680 × 1,050), compatible with non-

interlaced signals only, dot clock: 25.2 MHz–146.25 MHz

G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;

B, R: 0.7 Vp-p, 75 ohms;

HD/VD, SYNC: high impedance, TTL (positive/negative)

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal);

PB(CB), PR(CR): 0.7 Vp-p, 75 ohms

D-sub HD 15-pin (female) × 1

G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;

B, R: 0.7 Vp-p, 75 ohms;

HD/VD, SYNC: high impedance, TTL (positive/negative)

NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.

Y: 1.0 Vp-p (including sync signal);

PB(CB), PR(CR): 0.7 Vp-p, 75 ohms

RCA pin × 1, 1.0 Vp-p, 75 ohms

Mini DIN 4-pin × 1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms

M3 × 1 (L, R × 1), input impedance: 22 kilohms or more

M3 × 1 (L, R × 1), 0.5 Vrms, input impedance: 22 kilohms or more

RCA × 2 (L, R × 1), 0.5 Vrms, input impedance: 22 kilohms or more

M3 × 1 (L, R × 1) (monitor out: 0–2.0 Vrms, variable)

D-sub 9-pin × 1, for external control (parallel)

RJ-45 × 1, for network connection, 100Base-TX/10Base-T, compliant

with PJLink™

Connector for optional wireless module ET-WM200U/WM200E × 1

2.0 m (6 ft 7 in)

Molded plastic (PC + ABS)

430 mm × 125.5 mm*4× 323 mm

(16-15/16 × 4-15/16*4× 12-23/32 inches) (including the lens)

Approximately 6.0 kg (13.2 lbs)

33 dB (lamp mode: NORMAL), 29 dB (lamp mode: ECO)

0°–40°C (32°–104°F)*5

20%–80% (no condensation)

3 V DC (R6/LR6/AA type battery × 2)

Approximately 15 m (49 ft 3 in) when operated from directly in front of

the signal receptor

48 × 163 × 24.5 mm (1-13/32˝ × 6-5/8˝ × 31/32˝)

Approx. 117 g (4.1 oz) (including batteries)

Power cord with security lock (× 1)

Wireless remote control unit (× 1)

Batteries for remote control (AA/R6/LR6 type × 2)

Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring

and Control Software Ver. 2.5, Wireless Manager ME 5.5) (× 1)

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

4/13

Weights and dimensions shown are approximate. Specifications subject to change without notice.

*1 When the standby mode is set to ECO, network functions such as power on over the LAN network will not operate. Also, only certain com-

mands can be received for external control using the serial terminal.

*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.

*3 The DVI-I IN terminal also accepts analog signals.

*4 With legs at shortest position.

*5 Operation range differs depending on environments.

*6 The operating temperature range is 0°C–35°C (32°F–95°F) when used in High-Altitude mode (1,400 m (4,593 ft) to 2,700 m (8,858 ft)).

*7 The operation system must be pre-installed at the factory or clean installed.

Wireless Manager ME 5.5 system requirements

Web browser

CPU

Memory

Free hard disk space

CD-ROM drive

Wireless LAN

Wired LAN connector

Optional accessories

Replacement lamp unit

Replacement filter unit

Ceiling mount bracket

Wireless module

To use network functions, a PC is required that meets the conditions

given below.

Microsoft®

Windows®XP: Professional 32-bit, Home Edition 32-bit, Tablet PC

Edition 2005 32-bit

Windows Vista®: Ultimate 32-bit/64-bit, Business 32-bit/64-bit, Home

Premium 32-bit/64-bit, Home Basic 32-bit/64-bit

Windows®7: Ultimate 32-bit/64-bit, Professional 32-bit/64-bit,

Home Premium 32-bit/64-bit

Apple Mac OS X*7: v10.4, v10.5, v10.6

Windows®: Internet Explorer 6.0/7.0/8.0

Mac OS: Safari 2.0/3.0/4.0

Windows®: 1 GHz or higher Intel®Pentium®III or higher, or

other compatible processor

Mac OS X: 1 GHz or higher PowerPC G4, or 1.8 GHz or higher

Intel®Core™processor

256 MB or more (512 MB or higher is recommended for Mac OS X)

60 MB or more

CD-ROM drive or DVD drive (required for installation)

The optional ET-WM200 is required.

IEEE 802.11b/g/n compatible (built-in wireless LAN system or external

IEEE 802.11b/g/n LAN card must be installed and running normally.)

NOTE: Wireless connection may not be possible with some IEEE 802.11b/g/n wireless

LAN systems. Macintosh computers must have a built-in wireless LAN adapter.

For IEEE 802.11n connection, use a wireless LAN adapter, projector and access

point that are IEEE 802.11n compatible, and connect with Infrastructure mode.

RJ-45

ET-LAF100A

ET-EMF100

ET-PKF110H (for high ceilings)

ET-PKF110S (for low ceilings)

ET-WM200U (for North America)

ET-WM200E (for Europe and Asia)

323

53 228.5

430

(2-3/32) (9)

(16-15/16)

11510.5

125.5

(12-23/32)

(4-17/32)(13/32)

(4-15/16)

(2-25/32)

Dimensions

unit : mm (inch)

NOTE: This illustration is not drawn to scale.

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

5/13

Terminals

AC IN

AUDIO IN AUDIO IN 3

VARIABLE

AUDIO OUT

MAIN

POWER

COMPUTER IN S-VIDEO IN

DVI-I IN

LAN

SERIAL IN

VIDEO

OFF ON

7891011

23456

1 LAN connector

2 HDMI input

3 DVI-I input

4 Computer input

5 S-Video input

6 Video input

7 Serial input

8 Audio input 1

9 Audio input 2

10 Audio input 3

11 Audio output

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

6/13

Standard setting-up position

Projected image

Lower edge of projected image

Upper edge of projected image

Projected image

369–449

(14-17/32–

17-11/16)

Adjustable in

20-mm

(15/32-inch) step.

194

∅49

∅42

(2-9/16)

13 (1/2)

(7-5/8)

(1-15/16)

(1-11/16)

(2-3/4)

unit : mm (inch)

** Adjustable in 20 mm (25/32˝) steps.

NOTE:

Illustrations show the projector

installed using optional ceiling mount

bracket ET-PKF110H.

This illustration is not drawn to scale.

0.84 m

1.02 m

1.27 m

1.52 m

1.78 m

2.03 m

2.29 m

2.54 m

3.05 m

3.81 m

5.08 m

6.35 m

7.62 m

–

1.2

1.5

1.8

2.1

2.4

2.7

3.0

3.6

4.5

6.1

7.6

9.1

1.9

2.4

3.0

3.6

4.2

4.8

5.4

6.0

7.2

9.0

12.0

15.1

18.1

0.50

0.61

0.76

0.91

1.07

1.22

1.37

1.52

1.83

2.29

3.05

3.81

4.57

–

33˝

40˝

50˝

60˝

70˝

80˝

90˝

100˝

120˝

150˝

200˝

250˝

300˝

(–)

(3.8)

(4.8)

(5.8)

(6.8)

(7.8)

(8.9)

(9.9)

(11.9)

(14.9)

(19.9)

(24.9)

(29.9)

(6.4)

(7.8)

(9.7)

(11.7)

(13.7)

(15.7)

(17.7)

(19.7)

(23.6)

(29.6)

(39.5)

(49.4)

(59.3)

1.7)

2.0)

2.5)

3.0)

3.5)

4.0)

4.5)

5.0)

6.0)

7.5)

10.0)

12.5)

15.0)

–

Projection size

[diagonal]

Projection distance [L]

Min [wide] Max [telephoto]

Height from the edge of screen

to center of lens [H]

Projection distance for 4:3 aspect ratio screen

unit: meters (feet)

NOTE:

• The value for H (the height from the edge of the screen to the centre of the lens) is the value when the horizontal optical axis shift function is

not used. The value decreases when the horizontal optical axis shift function is used. For details, see Shift range on page 7.

• The value for L (distance to screen) varies slightly depending on the zoom lens characteristics.

• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.

• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.

• The brightness varies depending on the zoom setting.

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

7/13

Calculation of the projection distance

For a screen size different from the above, use the equation below to calculate the projection distance.

Aspect ratio 4:3

minimum L (m) = (diagonal screen size in inches) × 0.0305 – 0.049

maximum L (m) = (diagonal screen size in inches) × 0.0604 – 0.050

NOTE:

Distances calculated with the above equations will include a slight error.

(Width of

projected image)

(Height of

projected image)

0.5V 0.5V

0.27H0.27H

Standard postition

of projected image

–30°

+30°

0°

Shift range

Optical axis shift function allows to shift the position of a projected image as shown below.

Installable angle

Install the projector at an angle within the range shown below.

• Vertical direction

The projector may be installed at a vertical

angle of 30°.

• Horizontal direction

The projector may not be angled horizontally.

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

8/13

List of compatible signals

The signals that can be input to this projector are shown in the table below. Horizontal scanning fre-

quencies of 15.6 kHz to 91.1 kHz, vertical scanning frequencies of 24.0 Hz to 85.1 Hz, and a dot clock

of 162 MHz maximum can be input.

NOTE: The native resolution of this projector is 1,024 × 768 pixels. If the display resolution of the input signal is different from the

native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.

Display mode Display

resolution

(dots)*1

Scanning frequency

(kHz)

Dot clock

frequency

(MHz)

Format Plug and Play compatibility

HDMI

input

DVI-D input

EDID1 EDID2

Computer/

DVI-I (analog)

720 × 480i

720 × 576i

720 × 480i

720 × 576i

720 × 483

720 × 576

1,280 × 720

1,920 × 1,080i

1,920 × 1,080

640 × 400

640 × 480

800 × 600

832 × 624

1,024 × 768

1,280 × 720

1,280 × 768

1,280 × 800

1,152 × 864

1,152 × 870

1,280 × 960

1,280 × 1,024

1,400 × 1,050

1,440 × 900

1,600 × 1,200

1,680 × 1,050

1,920 × 1,200

15.7

15.6

15.7

15.6

31.5

31.3

45.0

37.5

33.8

28.1

27.0

67.5

56.3

66.6

55.6

31.5

37.9

31.5

35.0

37.9

37.5

43.3

35.2

37.9

48.1

46.9

53.7

49.7

39.6

48.4

56.5

60.0

68.7

44.8

37.1

39.6

47.8

41.3

49.1

49.7

64.0

67.5

76.7

68.7

60.0

64.0

80.0

91.1

64.0

65.1

55.9

75.0

65.3

74.6

59.9

50.0

59.9

50.0

59.9

50.0

60.0

50.0

60.0

50.0

24.0

60.0

50.0

59.9

49.9

70.1

85.1

59.9

66.7

72.8

75.0

85.0

56.3

60.3

72.2

75.0

85.1

74.6

50.1

60.0

70.1

75.0

85.0

59.9

49.8

49.9

59.9

50.0

60.2

59.8

71.2

74.9

85.0

75.1

60.0

75.0

85.0

60.0

59.9

60.0

59.9

–

13.5

27.0

74.3

148.5

138.5

141.5

25.2

31.5

25.2

30.2

31.5

36.0

40.0

50.0

49.5

56.3

57.3

51.9

65.0

75.0

78.8

94.5

74.5

60.5

65.3

79.5

68.0

69.1

83.5

94.2

108.0

121.5

100.0

108.0

135.0

157.5

108.0

122.4

106.5

162.0

146.3

154.0

NTSC/NTSC4.43/

PAL-M/PAL60

PAL/PAL-N/SECAM

480i (525i)

576i (625i)

480p (525p)

576p (625p)

720 (750)/60p

720 (750)/50p

1080 (1125)/60i

1080 (1125)/50i

1080 (1125)/24p

1080 (1125)/60p

1080 (1125)/50p

1920 × 1080

VESA

VGA

SVGA

MAC

XGA

WIDE750 (720)

WXGA768

WXGA800

MXGA

MAC

MSXGA

SXGA

SXGA60+

WXGA+

UXGA

WSXGA+

WUXGA

VIDEO/S-VIDEO

COMPUTER/YPBPR

HDMI/DVI/COMPUTER/YPBPR

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

HDMI/DVI/COMPUTER

COMPUTER

Yes

*1 The “i” appearing after the resolution indicates an interlaced signal.

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

9/13

Serial connector

The serial connector complies with RS-232C. To control the projector from a personal computer, com-

mands must be input through communication software, based on the format and satisfying the commu-

nication conditions shown below.

Basic format

Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent

in this order. Add parameters according to the details of control.

Communication conditions (factory setting)

Pin assignments and signal names

D-sub 9-pin (female)

Serial input

Description

Send data

Receive data

Ground

Signal name

–

TXD

RXD

–

GND

No.

Description

Connected internally

Signal name

–

RTS

CTS

–

No.

CAUTION

• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 sec-

onds, then try sending or receiving again.

• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next

command.

• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10

seconds or more.

• When using two or more units, set different IDs for each unit.

Start

(1 byte)

End

(1 byte)

Colon

(1 byte)

Semicolon

(1 byte)

ID designator:

01 to 06: Projector ID number

ZZ: All units (ID ALL)

ID 2 characters

(2 bytes)

Parameters

(undefined length)

Command

(3 bytes)

(Control and/or query commands)

STX ETXC1 P1 P2 ... PnC2A D I1 I2 C3 :;

Signal level

Synchronization method

Baud rate

Parity

Character length

Stop bit

X parameter

S parameter

RS-232C-compliant

Start-stop synchronization

9,600 bps

None

8 bits

1 bit

None

SPEC FILE PT-FX400

LCD Projector

As of March 2011

SFL11M006-1

10/13

Cable specifications

PC (DTE)Projector

Control commands

PON*1

POF*1

AVL:<pl>

IIS:<input signal>

OST

OFZ:<off on>

OEN

OXG: 0

OXG: 1

OXG: 2

VPM:<NAT>

VPM:<STD>

VPM:<CIN>

VPM:<DYN>

VPM:<BBD>

VPM:<WBD>

VXX:DLVI0=<+00000>

VXX:DLVI0=<+00001>

VXX:DLVI0=<+00002>

AUU

AUD

OMN

OCU

OCD

OCL

OCR

OAS

OSH*1/*2

OIX

DZU

DZD

TSD:<date>

TST:<time>

Power on (standby mode on)

Power off (standby mode off)

Volume control

Input signal selection

The same function as “default” button

Freeze

Enter

Wide mode: Off

Wide mode: On

Wide mode: Auto

Picture mode: Natural

Picture mode: Standard

Picture mode: Cinema

Picture mode: Dynamic

Picture mode: Blackboard

Picture mode: Whiteboard

Daylight View: Off

Daylight View: Auto

Daylight View: On

Volume up

Volume down

Cursor up

Cursor down

Cursor left

Cursor right

Auto setup

AV mute

Index window

Digital zoom: Enlargement

Digital zoom: Reduction

Date setting

Time setting

PON*1

POF*1

AVL:<pl>

IIS:<input signal>

OST

OFZ:<off on>

OEN

OXG: 0

OXG: 1

OXG: 2

VPM:<NAT>

VPM:<STD>

VPM:<CIN>

VPM:<DYN>

VPM:<BBD>

VPM:<WBD>

VXX:DLVI0=<+00000>

VXX:DLVI0=<+00001>

VXX:DLVI0=<+00002>

AUU

AUD

OMN

OCU

OCD

OCL

OCR

OAS

OSH*1/*2

OIX

DZU

DZD

TSD:<date>

TST:<time>

–

Command: <Parameter> Function Callback: <Parameter> Parameter value

Min Max

*1 Do not send PON, POF or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replace-

ment cycle.

*2 When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.

Inhaltsverzeichnis

Andere Panasonic Projektor Handbücher

Panasonic

Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform... Bedienungsanleitung

Panasonic

Panasonic PTL6600U - LCD PROJECTOR Bedienungsanleitung

Panasonic

Panasonic PT-RZ16KU Betriebsanleitung

Panasonic

Panasonic PT-RQ32K Bedienungsanleitung

Panasonic

Panasonic PLC-XU75A Bedienungsanleitung

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

Panasonic

Panasonic PT-F200 Series Benutzerhandbuch

Panasonic

Panasonic PT-TX340 Bedienungsanleitung

Panasonic

Panasonic PT-AX200 Benutzerhandbuch

Panasonic

Panasonic PT-RZ870 Bedienungsanleitung

Panasonic

Panasonic PT-AE2000E Systemhandbuch

Panasonic

Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform... Bedienungsanleitung

Panasonic

Panasonic PT-EW530U Bedienungsanleitung

Panasonic

Panasonic PT-FW300NT Systemhandbuch

Panasonic

Panasonic PTFW100NTU - LCD PROJEC. WIRELESS Bedienungsanleitung

Panasonic

Panasonic PT-AE8000U Bedienungsanleitung

Panasonic

Panasonic PT-RW330 Leitfaden

Panasonic

Panasonic PT-LW321 Bedienungsanleitung

Panasonic

Panasonic PT-JX200HBU Bedienungsanleitung

Panasonic

Panasonic PT51G63 - 51" PROJECTION TV Bedienungsanleitung

Panasonic

Panasonic PT-FRQ60 Bedienungsanleitung

Panasonic

Panasonic PTL390U - LCD PROJECTOR Bedienungsanleitung

Panasonic

Panasonic PT-DW5000 Systemhandbuch

Panasonic

Panasonic PT-AT5000E Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung