Panasonic PTP1SDU - LCD PROJECTOR Bedienungsanleitung

rights reserved. Unauthorized copying and

distribution is a violation of law.

PT-P1SDU

PT-P1SDE

PT-P1SDEA

LCD Projector

ORDER NO. VED0601368C0

D10

PT-P1SDU / PT-P1SDE / PT-P1SDEA

1 Safety Precautions 5

1.1. General Guidelines 5

1.2. Leakage Current Check 5

1.3. UV Precaution and UHM Lamp Precautions 5

2 Ext Option 6

2.1. Procedure to enter EXT OPTION 6

2.2. EXT OPTION Menu and Functions 6

2.3. Canceling EXT OPTION 7

3 Self-Check Mode 7

3.1. Procedure to enter the self-check mode 7

3.2. Self Check Display and Contents 8

3.3. Canceling the self-check mode 8

4 Service Mode 9

4.1. Procedure to enter the service mode 9

4.2. Canceling the service mode 9

5 Flicker Adjustment Mode 9

5.1. Procedure to enter the adjustment mode 9

5.2. Adjustment Display and Contents 9

5.3. Canceling the flicker adjustment mode 9

6 Disassembly Instructions 10

6.1. Printed Circuit Board and Main Parts Location 10

6.2. Removal of Upper Case 11

6.3. Removal of A-P.C.Board 11

6.4. Removal of J-P.C.Board 11

6.5. Removal of R-P.C.Board 12

6.6. Removal of K-P.C.Board 12

6.7. Removal of B/Q-Module 12

6.8. Removal of P-P.C.Board 13

6.9. Removal of Z-P.C.Board 13

6.10. Removal of Lamp Unit 13

6.11. Removal of Analysis Block and Lens 14

6.12. Removal of LCD Block 14

6.13. Replacement of LCD Panel (B) 15

6.14. LCD Panel Discrimination 16

6.15. LCD Panel Combination 16

6.16. Replacement of Incidence Polarizer (B) 16

6.17. Replacement of Projection Polarizer (B, G) 17

6.18. Replacement of PBS Array (Analysis Block) 17

7 Measurement and Adjustments 19

7.1. Adjustment Procedure Flowchart 19

7.2. Cautions for Adjustment 19

7.3. Setting Before Adjustment 19

7.4. Convergence Adjustment 19

7.5. Lighting Area Adjustment 21

7.6. Software for Adjustment 23

7.7. Flicker Adjustment 25

7.8. Input Level Adjustment 25

7.9. Model Information Setup 26

8 Troubleshooting 27

9 Interconnection Block Diagram 37

9.1. Interconnection Block Diagram (1/2) 37

9.2. Interconnection Block Diagram (2/2) 38

10 Block Diagram 39

10.1. Power Supply 39

10.2. Signal Processing (1/2) 40

10.3. Signal Processing (2/2) 41

11 Schematic Diagram 43

11.1. A-P.C.Board (1/6) 44

11.2. A-P.C.Board (2/6) 45

11.3. A-P.C.Board (3/6) 46

11.4. A-P.C.Board (4/6) 47

11.5. A-P.C.Board (5/6) 48

11.6. A-P.C.Board (6/6) 49

11.7. J-P.C.Board 50

11.8. P-P.C.Board (1/2) 51

11.9. P-P.C.Board (2/2) 52

11.10. K-P.C.Board / R-P.C.Board / Z-P.C.Board 53

11.11. B-Module (1/2) 54

11.12. B-Module (2/2) 55

12 Circuit Boards 57

12.1. A-P.C.Board 57

12.2. J-P.C.Board / P-P.C.Board / R-P.C.Board 58

13 Terminal guide of ICs and transistors 59

14 Exploded Views 60

15 Replacement Parts List 63

CONTENTS

Page Page

PT-P1SDU / PT-P1SDE / PT-P1SDEA

1 Safety Precautions

1.1. General Guidelines

For continued safety, no modification of any circuit must be

attempted.

Unplug the power cord from the power outlet before

disassembling this projector.

Use correctly the supplied power cord and must ground it.

It is advisable to use an isolation transformer in the AC

power line before the service.

Observe the original lead dress during the service. If a short

circuit is found, replace all the parts overheated or

damaged by the short circuit.

After the service, all the protective devices such as

insulation barriers, insulation papers, shields, and isolation

R-C combinations must be properly installed.

After the service, check the leakage current to prevent the

customer from getting an electric shock.

1.2. Leakage Current Check

1.Prepare the measuring circuit as shown in Fig.1.

Be sure to use a voltmeter having the performance

described in Table 1.

Fig. 1

Table 1

Fig. 2

2.Assemble the circuit as shown in Fig. 2. Plug the power

cord in a power outlet.

3.Connect M1 to T1 according to Fig. 2 and measure the

voltage.

4.Change the connection of M1 from T1 to T2 and measure

the voltage again.

5.The voltmeter must read 0.375 V or lower in both of steps

3 and 4. This means that the current must be 0.75 mA or

less.

6.If the reading is out of the above standard, the projector

must be repaired and rechecked before returning to the

customer because of a possibility of an electric shock.

1.3. UV Precaution and UHM Lamp

Precautions

Be sure to unplug the power cord from the power outlet

when replacing the lamp.

Because the lamp reaches a very high temperature during

its operation, wait until it cools completely when replacing

the Lamp Unit.

The lamp emits small amounts of UV-radiation, avoid direct-

eye contact with the light.

The lamp unit has high internal pressure. If improperly

handled, explosion might result.

Because the high pressure lamp involves a risk of failure,

never touch the lamp wire lead during the service. (See Fig.

Fig.3

PT-P1SDU / PT-P1SDE / PT-P1SDEA

2 Ext Option

This projector has EXT OPTION in addition to standard on-screen menus.

There are SELF CHECK and SERVICE MODE for service, etc.

2.1. Procedure to enter EXT OPTION

1.Press "MENU" button on the remote control unit to display "MENU" screen, then select "OTHER SETUP" and press "ENTER"

button.

2.Select "HIGHTLAND" on "OTHER SETUP" menu and press "ENTER" button 3 seconds or longer.

MENU →OTHER SETUP →HIGHTLAND

2.2. EXT OPTION Menu and Functions

FREEZE MSG

Switching ON/OFF "FREEZE" on-screen display

ANGLE RESET

Resetting "AUTO SETUP (Correcting keystone distortion)" reference level

Note:

−

− −

− Normally, do not select. (Angle reset data will be rewritten.)

FAN FULLMODE

Setting the cooling fan motor rotation speed

−

− −

− Switching ON "FAN FULLMODE", the rotation level of the fan becomes high-speed rotation (fixed). Moreover, when "FAN

FULLMODE" is ON, changing "HIGHTLAND" in OTHER SETUP becomes impossible (setting FAN FULLMODE is given

priority more than HIGHTLAND).

AUTOSETUP

Setting AUTO SETUP mode

−

− −

− STANDARD: To set the normal mode (the dot clock is adjusted strictly))

−

− −

− SPECIAL: To set the special mode (the dot clock is adjusted roughly)

Note:

−

− −

− Do not change the initial setting (STANDARD).

SYNC

Setting SYNC processing mode

−

− −

− STANDARD: To set the normal mode

−

− −

− SPECIAL: To set the special mode (noise reduction mode)

Note:

−

− −

− Do not change the setting when it is possible to receive normally.

Change the setting only when the image is not displayed normally because of the sync signal noise of connected

equipment.

SELF CHECK

To enter the self-check mode

SERVICE MODE

PT-P1SDU / PT-P1SDE / PT-P1SDEA

To enter the service mode

FLICKER ADJ

To enter the flicker adjustment mode

HPLL

When non-standard signal of VIDEO/S-VIDEO is inputted (VCR, VHD, etc.), horizontal synchronization might be disordered

according to connected equipment. In this case, set H PLL to OFF.

2.3. Canceling EXT OPTION

Press "MENU" button on the remote control unit.

3 Self-Check Mode

This mode is used to narrow down the location of the failure.

3.1. Procedure to enter the self-check mode

Select "SELF CHECK" on "EXT OPTION" menu and press "ENTER" button on the remote control unit.

PT-P1SDU / PT-P1SDE / PT-P1SDEA

3.2. Self Check Display and Contents

3.3. Canceling the self-check mode

Press "MENU" button on the remote control unit.

PT-P1SDU / PT-P1SDE / PT-P1SDEA

4 Service Mode

This mode is used to display seven kinds of test patterns [Horizontal lines, Vertical lines, Dots, Crosshatch, White cross, Black

cross and White (No pattern)] in the four colors (White, Red, Green and Blue).

Note:

On the service mode, displays above patterns by each color without test equipment such as PC or SG. Use the service

mode for simplified adjustments by your eyes and so on.

4.1. Procedure to enter the service mode

Select "SERVICE MODE" on "EXT OPTION" menu and press "ENTER" button on the remote control unit.

Note:

In the service mode, pressing the up-arrow " " or down-arrow " " button allows the test pattern selection and the

left-arrow " " or right-arrow " " button the color selection (White / Red / Green / Blue).

4.2. Canceling the service mode

Press "MENU" button on the remote control unit.

5 Flicker Adjustment Mode

If replacing the optical parts (Analysis / LCD / Lens block) of this projector and/or A-P.C.Board (assembly), enter the flicker

adjustment mode and minimize the flicker.

5.1. Procedure to enter the adjustment mode

Select "FLICKER ADJ" on "EXT OPTION" menu and press "ENTER" button on the remote control unit.

Note:

"DESK setting (blue)" is displayed when entering the adjustment mode.

5.2. Adjustment Display and Contents

Setting value is increased and decreased with the right-arrow " " and left-arrow " " buttons.

"": Decrease, " ": Increase

−

− −

− Adjust the setting value to minimize the flicker on the screen.

−

− −

− Execute the adjustment by 6 patterns below.

The pattern (adjustment display) is switched with the up-arrow " " and down-arrow " " buttons.

"": Forward direction, " ": Reverse direction

−

− −

− There are 6 patterns of "DESK setting (blue)", "DESK setting (red)", "DESK setting (green)", "CEILING setting (blue)",

"CEILING setting (red)" and "CEILING setting (green)".

−

− −

− The setting value is saved into this projector when the pattern is switched.

5.3. Canceling the flicker adjustment mode

Press "MENU" button on the remote control unit.

Note:

When "MENU" button is pressed, the setting value at that time is saved into this projector and the adjustment mode is canceled.

PT-P1SDU / PT-P1SDE / PT-P1SDEA

6 Disassembly Instructions

Warning:

Be sure to unplug the power cord from the power outlet before disassembling this projector.

Caution:

While turning over a printed circuit board, be sure to put a insulating material under it to prevent a short circuit.

Printed circuit boards and wires must not be pulled forcibly, but be handled carefully.

Connectors also must be handled carefully.

After repairing this projector, be sure to put back the wires and connectors to the original condition.

6.1. Printed Circuit Board and Main Parts Location

Electrical Parts

Optical Parts

PT-P1SDU / PT-P1SDE / PT-P1SDEA

Andere Handbücher für PTP1SDU - LCD PROJECTOR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Panasonic Projektor Handbücher

Panasonic

Panasonic PT-JX200FBU Bedienungsanleitung

Panasonic

Panasonic PT-DZ13KE Bedienungsanleitung

Panasonic

Panasonic PT-AE500E Bedienungsanleitung

Panasonic

Panasonic PT PT-D5000ULS Bedienungsanleitung

Panasonic

Panasonic PT-LZ370E Bedienungsanleitung

Panasonic

Panasonic PT-CW331R Bedienungsanleitung

Panasonic

Panasonic PT-LB20NT Bedienungsanleitung

Panasonic

Panasonic PTLC50U - LCD PROJECTOR Bedienungsanleitung

Panasonic

Panasonic PT-DW10000 Bedienungsanleitung

Panasonic

Panasonic PT-LC50E Bedienungsanleitung

Panasonic

Panasonic PT-FW100 Bedienungsanleitung

Panasonic

Panasonic PTL292U - LCD PROJECTOR Bedienungsanleitung

Panasonic

Panasonic PT-LB50 Bedienungsanleitung

Panasonic

Panasonic PTL597UL - LCD VIDEO PROJRCTOR Bedienungsanleitung

Panasonic

Panasonic PT-F100NTE Montage- und Wartungsanleitung

Panasonic

Panasonic PT-LB10NTU - Mobile Proj XGA 2000 Lumens 4.9LBS Cross Platform... Bedienungsanleitung

Panasonic

Panasonic PT-AT5000E Bedienungsanleitung

Panasonic

Panasonic PT-L780U Bedienungsanleitung

Panasonic

Panasonic PTAE3000U - HOME THEATER LCD PROJECTOR Bedienungsanleitung

Panasonic

Panasonic PTL6600U - LCD PROJECTOR Bedienungsanleitung

Panasonic

Panasonic PT-TW231RU Bedienungsanleitung

Panasonic

Panasonic PT-VW355N Bedienungsanleitung

Panasonic

Panasonic PT-EZ570UL Bedienungsanleitung

Panasonic

Panasonic PT-FRZ55B Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung