Panasonic SAAK22 - MINI HES W/CD-PLAYER Bedienungsanleitung
Q
QQ
QAMPLIFIER SECTION
RMS power output
THD 10%, both channels driven
both channel driven
(E,EB) 80 W per channel (6 Ω)
(EG) 60 W per channel (6 Ω)
Input sensitivity
AUX 250 mV
Input Impedance
AUX 13 kΩ
Q
QQ
QFM TUNER SECTION
Frequency range 87.50 - 108.00 MHz (50 kHz
steps)
Sensitivity 1.8 µV (IHF)
S/N 26 dB 1.5 µV
Antenna terminal(s) 75 Ω(unbalanced)
Q
QQ
QAM TUNER SECTION
Frequency range 522 - 1629 kHz (9 kHz steps)
Sensitivity
S/N 20 dB (at 999 kHz) 560 µV/m
Q
QQ
QCASSETTE DECK SECTION
Track system 4 track, 2 channel
© 2001 Matsushita Electronics (S) Pte. Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
SA-AK22
Colour
(S)... Silver Type
Area
(E)... Europe
(EB)... Great Britain
(EG)... Germany and Italy
TAPE SECTION :
SG-2W MECHANISM SERIES
CD SECTION :
RAE0152Z-3 TRAVERSE DECK SERIES
Heads
Record/playback Solid permalloy head
Erasure Double gap ferrite head
Motor DC servo motor
Recording system AC bias 100 kHz
Erasing system AC erase 100 kHz
Tape speed 4.8 cm/s
Frequency response (+3 dB, -6 dB at DECK OUT)
NORMAL (TYPE I) 35 Hz - 14 kHz
S/N 50 dB (A weighted)
Wow and flutter 0.18% (WRMS)
Fast forward and rewind time Approx. 120 seconds with
C-60 cassette tape
Q
QQ
QCD SECTION
Sampling frequency 44.1 kHz
Decoding 16 bit linear
Beam source/wave length Semiconductor laser/780 nm
Number of channels Stereo
Frequency response 20 Hz - 20 kHz (+1, -2 dB)
Wow and flutter Below measurable limit
Digital filter 8fs
D/A converter MASH (1 bit DAC)
CD Stereo System
Specifications
ORDER NO. MD0105096C2
Q
QQ
QGENERAL
Power supply
(E,EG) AC 230-240V, 50 Hz
(EB) AC 230, 50 Hz
Power consumption 170 W
Power consumption in standby mode
0.4 W
Dimensions (W x H x D) 250 x 332 x 316 mm
Mass 8.2 kg
Q
QQ
QSYSTEM
SC-AK22 (E) Music Center: SA-AK22 (E)
1 Before Repair and Adjustment 2
2 Protection Circuitry 2
3 Accessories 3
4 Handling Precautions For Traverse Deck 4
5 Precaution of Laser Diode 5
6 Caution for AC Mains Lead 6
7 Operation Procedures 7
8 Disassembly and Main Component Replacement Procedures
9
9 Self-Diagnostic Function 19
10 Description of Error Code 20
Speaker: SB-AK22 (E)
SC-AK22 (EB) Music Center: SA-AK22 (EB)
Speaker: SB-AK22 (E)
SC-AK22 (EG) Music Center: SA-AK22 (EG)
Speaker: SB-AK22 (E)
Notes:
1.Specifications are subject to change without notice. Weight and
dimensions are approximate.
2.Total harmonic distortion is measured by the digital spectrum
analyzer.
11 CD Test Mode Function 21
12 Measurements and Adjustments 21
13 Illustration of IC’s, Transistors and Diodes 24
14 Terminal Function of IC’s 25
15 Block Diagram 29
16 Schematic Diagram 35
17 Printed Circuit Board 48
18 Wiring Connection Diagram 59
19 Troubleshooting Guide 60
20 Parts Location and Replacement Parts List 61
CONTENTS
Page Page
1 Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C536, C545, C546 through a 10 Ω, 5W resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 230 V, 50 Hz in NO SIGNAL mode should be ~400mA.
2 Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
•
••
•
No sound is heard when the power is turned on.
•
••
•
Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1.Turn off the power.
2.Determine the cause of the problem and correct it.
3.Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
2
S
A-AK22
3 Accessories
Remote Control
Transmitter
FM indoor antenna (E,EB)
FM indoor antenna (EG)
AC mains lead (E,EG)
AC mains lead (EB)
AM Loop antenna
Antenna Plug Adaptor (EB)
3
SA-AK2
2
4 Handling Precautions For Traverse Deck
The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of
clothes or human body.
So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
•
••
•
Handling of traverse deck (optical pickup)
1.Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock.
2.The short land between the No.4(LD) and No.5(GND) pins on the flexible board (FFC) is shorted with a solder build-up to
prevent damage to the laser diode.To connect to the PC board, be sure to open by removing the solder build-up, and finish the
work quickly.
3.Take care not to apply excessive stress to the flexible board (FFC).
4.Do not turn the variable resistor (laser power adjustment). It has already been adjusted.
•
••
•
Grounding for electrostatic breakdown prevention
1.Human body grounding
Use the anti-static wrist strap to discharge the static electricity from your body.
2.Work table grounding
Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is placed, and ground
the sheet.
Caution :
The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the
traverse deck (optical pickup).
Caution when Replacing the Traverse Deck :
The traverse deck has a short point shorted with solder to protect the laser diode against electrostatics breakdown. Be sure to
remove the solder from the short point before making connections.
4
S
A-AK22
5 Precaution of Laser Diode
Caution :
This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens.
Wavelength : 780 nm
Maximum output radiation power from pick up : 100 µW/VDE
Laser radiation from pick up unit is safety level, but be sure the followings:
1.Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous.
2.Do not adjust the variable resistor on the pick up unit. It was already adjusted.
3.Do not look at the focus lens using optical instruments.
4.Recommend not to look at pick up lens for a long time.
ACHTUNG :
Dieses Produkt enthält eine Laserdiode. Im eingeschalteten Zustand wird unsichtbare Laserstrahlung von der Lasereinheit
abgestrahlt.
Wellenlänge : 780nm
Maximale Strahlungsleistung der Lasereinheit :100 µW/VDE
Die Strahlung an der Lasereinheit ist ungefährlich, wenn folgende Punkte beachtet werden:
1.Die Lasereinheit nicht zerlegen, da die Strahlung an der freigelegten Laserdiode gefährlich ist.
2.Den werkseitig justierten Einstellregler der Lasereinhit nicht verstellen.
3.Nicht mit optischen Instrumenten in die Fokussierlinse blicken.
4.Nicht über längere Zeit in die Fokussierlinse blicken.
ADVARSEL: I dette a apparat anvendes laser.
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
Q
QQ
QUse of Caution Labels
5
SA-AK2
2
6 Caution for AC Mains Lead
6
S
A-AK22
7 Operation Procedures
7
SA-AK2
2
8
S
A-AK22
Some chassis components may have sharp edges.
Be careful when disassembling and servicing.
•
••
•
Main Component Replacement Procedures
8 Disassembly and Main Component Replacement
Procedures
“ATTENTION SERVICER”
1.
This section describes procedures for checking the operation of the major printed circuit boards and replacing the
main components.
2.
For reassembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
3.
Select items from the following index when checks or replacement are required.
Contents
•
••
•
Disassembly and assembly main unit
1.Checking of the Main, Panel and Deck P.C.B.
2.Checking of the Power P.C.B.
1.Replacement of the Traverse Deck.
2.Replacement of the Power Amplifier IC.
•
••
•
Disassembly and assembly of the Traverse Unit
•
••
•
Disassembly and assembly of the Disc Tray
Warning:
This product uses a laser diode. Refer to caution statement Precaution of Laser Diode.
ACHTUNG:
Die Lasereinheit nicht zerlegen.
Die Lasereinheit darf nur gegen eine vom Hertsteller spezifizierte Einheit ausgetauscht werden.
9
SA-AK2
2
Step 2 Remove the top cabinet.
Step 3 Remove the T-bracket.
Step 5 Turn locating pin on both sides 90°. (Locating pin need
not to be bent back.)
Step 6 Release the wires CN302, CN303, CN304, CN309 and
CN502. Remove rear panel by pulling it backward and lift the
rear panel assembly.
8.1. Disassembly Procedure For Each Major P.C.B. checking
8.1.1. Checking of the Main, Transformer, Panel and Deck P.C.B.
10
S
A-AK22
Andere Handbücher für SAAK22 - MINI HES W/CD-PLAYER
4
Inhaltsverzeichnis
Andere Panasonic Stereoanlage Handbücher
Panasonic
Panasonic SCDV150 - MINISYS 5-D DVD CHGR Bedienungsanleitung
Panasonic
Panasonic RX-D50EE Bedienungsanleitung
Panasonic
Panasonic SC-HTB570 Bedienungsanleitung
Panasonic
Panasonic SC-TM72DV Bedienungsanleitung
Panasonic
Panasonic SC-AK200 Bedienungsanleitung
Panasonic
Panasonic SCEN5 - DESKTOP CD AUDIO SYS Bedienungsanleitung
Panasonic
Panasonic SC-CH64M Bedienungsanleitung
Panasonic
Panasonic RX-ES29GS Bedienungsanleitung
Panasonic
Panasonic SC-AK95 Bedienungsanleitung
Panasonic
Panasonic SCAK14 - MINI HES W/CD-PLAYER Bedienungsanleitung
Panasonic
Panasonic SA-HT740GCP Bedienungsanleitung
Panasonic
Panasonic SC-HC05 Bedienungsanleitung
Panasonic
Panasonic SA-PMX3GN Bedienungsanleitung
Panasonic
Panasonic RX-DT650 Bedienungsanleitung
Panasonic
Panasonic SA-HD52 Bedienungsanleitung
Panasonic
Panasonic SCPM22 - CD STEREO SYSTEM Bedienungsanleitung
Panasonic
Panasonic SC-HC30EF Bedienungsanleitung
Panasonic
Panasonic SC-EN15 Bedienungsanleitung
Panasonic
Panasonic RXES30 - RADIO CASSETTE W/CD Bedienungsanleitung
Panasonic
Panasonic SCPM15 - CD STEREO SYSTEM Bedienungsanleitung
