Panasonic Nanoe EH-HS99 Bedienungsanleitung

Order Number PEWT1711M40CE

Model No.

EH-HS99

TABLE OF CONTENTS

PAGE

1 Warning --------------------------------------------------------------------

2 Specifications -------------------------------------------------------

3 Troubleshooting Guide ----------------------------------------------

4 Disassembly and Assembly instructions --------------------------

5 Wiring Connection Diagram -----------------------------------------

6 Schematic Diagram -----------------------------------------------

7 Explode View and Replacement Part List -------------------------------

(Household) Hair Straightener

Middle East

and distribution is a violation of law.

1. Warning

Caution:

- Pb free solder has a higher melting point that standard solder typically the melting point

is 50 - 70°F (30 - 40°C) a higher. Please use soldering iron with temperature control

and adjust it to 700±20°F (370 ± 10°C).

In case of using high temperature soldering iron, please be careful not to heat too long.

- Pb free solder will tend to splash when heated too high (about 1100°F / 600℃).

Model

Sales Area

Power source / AC 100-120V ~ 50-60Hz

Power consumption AC 220-240V ~ 50-60Hz

Iron Plate temperature 150-170-180-200-230℃(5 level settings)

Body size (mm.)

Weight

Cord length

2. Specifications

1.7m

EH-HS99

Middle East

38.0W (Max.41.8W)

S3 Plug (SF629)

450g

286×33×44

S3 Plug (SF629)

3.TROUBLESHOOTING GUIDE

Refer to WIRING CONNECTION DIAGRAM.

Before insert the POWER CORD to CONNECTOR COVER ASSEMBLY,

must check if the terminal inside the CONNECTOR COVER ASSEMBLY is deformed.

< CHECKING PROCEDURE >

< CHECKING METHOD >

< REMEDY >

Check the

POWER CORD

Check the conductivity of

POWER CORD

Check the

HEATER A ASSEMBLY

Check if the Resistance value

between lead wire Purple and Black

is 29-34Ω

Check the Switch button

(Power switch and Temp.

adjust switch)

Check the operation of Switch button

(Power switch and Temp. adjust

switch) on HOUSING B.

(Check if it works smoothly)

Temp. adjust switch

(Micro) PCB

Power switch

LED (Temp. level lamp)

150

170

180

200

230

Current Fuse

No operation.

- LED does not light

- Iron plate does not become hot

- Nano-e does not generate

Replace the

POWER CORD

Re-assembly or replace

the Switch button

Replace the

HEATER A SSEMBLY

Check the

HEATER B ASSEMBLY

Check if the Resistance value

between lead wire Yellow and Gray

is 29-34Ω

Check (Micro) PCB Press the Tag switch on (Micro) PCB

and check if the LED lights. Replace the

HEATER A ASSEMBLY

Replace the

HEATER B ASSEMBLY

Terminal

Power cord

< CHECKING PROCEDURE >

< CHECKING METHOD >

< REMEDY >

Check if the Resistance value

between lead wire Purple and Black

is 29-34Ω

(Micro) PCB

Temp. adjust switch

Power switch

LED (Temp. level lamp)

Current Fuse

150

170

180

200

230

LED does not light

Replace the

HEATER A ASSEMBLY

Cheak the

HEATER B ASSEMBLY

Check if the Resistance value

between lead wire Yellow and Gray

is 29-34Ω

Check (Micro) PCB Press the Tag switch on (Micro) PCB

and check if the LED lights. Replace the

HEATER A ASSEMBLY

Replace the

HEATER B ASSEMBLY

Replace the

HEATER A ASSEMBLY

Iron plate (Heater) does not

become hot but LED lights.

Cheak the

HEATER A ASSEMBLY

Temp. does not change when

press the Temp. adjust switch

Check the Switch button

(Power switch and

Temp. adjust switch)

Check the operation of Switch button

(Power switch and Temp. adjust

switch) on HOUSING B.

(Check if it works smoothly)

Re-assembly or replace

the Switch button

Nano-e does not generate

Clean the Nano-e hole

Replace the

HEATER B ASSEMBLY

Check the working condition of Nano-e

(check If it has abnormal noise at Nano-e hole)

4. Disassembly and Assembly instructions

4.1 Disassembly instruction

(1) Remove SHAFT COVER from Main body (4) Remove PIVOT SPRING by gripping

by slotted screw driver (Minus driver). and pull it out from the Main body.

NOTE: Use NEW SHAFT COVER once disassembling

due to easily breakage or looseness of hook.

(2) Remove TORX SCREW at SHAFT position

by screw driver (Star driver).

(5) Remove TAPPING SCREWS at PRESS PLATE COVER

by screw driver (Plus driver) and pull out

PRESS PLATE COVER from Main body.

(3) Remove SHAFT out by tiny-shaped screw driver

and pull it out from Main body

(6) Take off (HV) PCB from hook of PRESS PLATE 3 positions.

Minus driver

Shaft cover

Hook

Torx screw

Shaft

Tiny-shaped screw driver

Pivot spring

Tapping screws

Tapping screws Tapping screws

Tapping screws

Press plate cover

Hook

(HV) PCB

Heater B

(7) Remove SLIDE LOCK PLATE from Main Body (9) Take off (Micro) PCB from hook of HOUSING A

by slotted screw driver (Minus driver) 2 positions.

*Insert screw driver to hook inside SLIDE LOCK PLATE.

(10) Remove soldering point for taking off

lead wire 6 positions (Red, Blue, White, Gray,

Yelow, Brown) from (Micro) PCB.

(8) Remove TAPPING SCREWS at HOUSING B

by screw driver (Plus driver) and pull out

HOUSING B from Main body.

(10) Remove soldering point at Lead wire Red

and Blue for taking off CONNECTOR COVER ASSEMBLY

* Be careful not to lose the Floating SPRING 4 pcs on HOUSING A

Hook Slide Lock Plate

Minus driver

Floating springs

Housing A

Tapping screws (Big size)

Tapping screws (Small size)

Hook (Micro) PCB

Blue Red White

Gray Yellow Brown

Red

Blue

Soldering point

Connector cover assembly

4.2 Assembly Instructions

(1) Assembly point of HOUSING A (2) SHAFT fixing point. Have control direction.

Check the POWER CORD must be correctly assembled

with CONNECTOR COVER ASSEMBLY

*Apply a little of Grease Floil to Terminal of

POWER CORD.

(3) SHAFT COVER fixing point. Have control direction.

4.3 Lead wire of HEATER B ASSEMBLY and Circuit arrangement points.

(1) Assembled HEATER B ASSEMBLY with PRESS PLATE by arrangement Lead wire as figure 1.

and must insert all Lead wires pass through the Tube before soldering.

Figure 1.

(2) Assembled HEATER A ASSEMBLY with HOUSING A by arrangement Lead wire as figure 2.

and must insert all Lead wires pass through the Tube before soldering.

Figure 2.

Power cord

Connector cover assembly

Control position of Press plate side

Control position

of Shaft cover

Control position of Press Plate side

Control position

of Shaft

White

Brown

Blue

White

Red

Orange

Gray

Yellow

Heater B assembly

Gray

Black

Purple

Red

Blue White Red

Blue

Yellow Brown

Rib

Tube

Heater A assembly

4.3 Check list after assembly

Apply voltage to Main body and press the Power Switch, The Main body must be follow below items.

(1) LED Lights

(2) Both Iron Plate become hot.

(3) Ion is generated effectively

(4) Able to lock.

5.Wiring Connection Diagram

Iron plate (Heater A side)

Iron plate (Heater B side)

Moisture assembly block

Yellow

(TH+)

Yellow

(TH-) Red

(NANO)

Blue

(IPD) White

(AC2-2)

Black

(HA-) Red

(AC2)

Blue

(AC1)

Brown

(AC1-2)

Yellow

(HA+)

Purple

(HB-)

Gray

(HT)

Orange

(N_GND) White

(AC2-2)

Red

(NANO) Blue

(IPD)

Brown

(AC1-2)

Black

6. Schematic Diagram

7. EXPLODED VIEW & REPLACEMENT PARTS LIST

7.1. Exploded View

All parts are supplied from PMFTH-AP through PLAP

Andere Handbücher für nanoe EH-HS99

Inhaltsverzeichnis

Andere Panasonic Styling-Eisen Handbücher

Panasonic

Panasonic EH1771 Bedienungsanleitung

Panasonic

Panasonic nanoe EH-HS99 Bedienungsanleitung

Panasonic

Panasonic EH-HW58 Bedienungsanleitung

Panasonic

Panasonic EH-HV10 Bedienungsanleitung

Panasonic

Panasonic EH-HS95 Bedienungsanleitung

Panasonic

Panasonic EH-2351 Bedienungsanleitung

Panasonic

Panasonic EH-HV70 Bedienungsanleitung

Panasonic

Panasonic EH-HS41 Bedienungsanleitung

Panasonic

Panasonic EH-HT40 Bedienungsanleitung

Panasonic

Panasonic EH-HV40 Bedienungsanleitung

Panasonic

Panasonic EH-HS60 Bedienungsanleitung

Panasonic

Panasonic EH-HS0E Bedienungsanleitung

Panasonic

Panasonic Nanoe EH-PHS9K Bedienungsanleitung

Panasonic

Panasonic EH-HV52 Bedienungsanleitung

Panasonic

Panasonic EH-HS41 Bedienungsanleitung

Panasonic

Panasonic EH-HV11 Bedienungsanleitung

Panasonic

Panasonic EH-HV20 Bedienungsanleitung

Panasonic

Panasonic EH-HS95 Bedienungsanleitung

Panasonic

Panasonic EH-HW11 Bedienungsanleitung

Panasonic

Panasonic EH-HW19 Bedienungsanleitung

Panasonic

Panasonic EH-HV11 Bedienungsanleitung

Panasonic

Panasonic EH-HS95 Bedienungsanleitung

Panasonic

Panasonic EH-HW32 Bedienungsanleitung

Panasonic

Panasonic EH-HV10 Bedienungsanleitung

Beliebte Styling-Eisen Handbücher anderer Marken

Vitek

Vitek VT-2505 Bedienungsanleitung

Morphy Richards

Morphy Richards IB22063 Produktinformationsblatt

TZS First AUSTRIA

TZS First AUSTRIA Ida FA-5670-3 Bedienungsanleitung

izzy

izzy LN-112 Bedienungsanleitung

Vitek

Vitek VT-2310 Bedienungsanleitung

Okoia

Okoia HS23 Bedienungsanleitung

Arzum

Arzum TRENDCARE AR 5042 Bedienungsanleitung

SOLAC

SOLAC PP7251 Bedienungsanleitung

VS Sassoon

VS Sassoon VSLE330A Bedienungsanleitung

Philips

Philips HP8339 Bedienungsanleitung

Philips

Philips HP4666 Bedienungsanleitung

Vitek

Vitek VT-8291 Bedienungsanleitung

VS Sassoon

VS Sassoon miniPRO Wave Envy Bedienungsanleitung

Arzum

Arzum SUPERSTAR TOUCH Bedienungsanleitung

Remington

Remington S2880ZBA Bedienungsanleitung

cecotec

cecotec Bamba RitualCare 900 Wet&Dry Max Bedienungsanleitung

Philips

Philips HPS950 Bedienungsanleitung

Andis

Andis Gold CSI-1E Bedienungsanleitung